HomeMy WebLinkAbout34153-ZFORM NO. 4
TOWN OF SOUTHOLD
BUILDING DEPARTMENT
Office of the Building Inspector
Town Hall
Southold, N.Y.
CERTIFICATE OF OCCUPANCY
No: Z-33385
Rte: 11/14/08
CERTIFIES that the building WOODSTOVE
Location of Property: 295 OLD ORCHARD LA
(HOUSE NO.)
County Tax Map NO. 473889 Section 31
Su]m~ivision
EAST MARION
(STREET) (H~4LET)
Block 7 Lot 21
Filed Map NO. Lot NO. __
conforms substantially to the Application for Building Permit heretofore
filed in this office dated SEPTEMBER 10, 2008 purs%~nt to which
Building Permit No. 34153-Z dated SEPTEMBER 12, 2008
was issued, and conforms to all of the requirements of the applicable
provisions of the law. The occupancy for which this certificate is issued
is WOOD STOVE INSTALLED IN AN EXISTING ONE FAMILY DWELLING AS APPLIED FOR.
The certificate is issued to DOUGLAS & SHARON ROGERS JR
( OWNER )
of the aforesaid building.
Rev. 1/81
TO. OF O ;T.O.
BUILDING DEPARTMENT /L/U/ In_ ~'~//~ '
,/
APPLICATION FOR CERTIFICATE OF OCCUP~C~L~O/~
This application must be filled in by typewriter or i~ and suNmtted to the Building Depamneut with the follbwing:
A. For new building or new use: 1. Final survey of prope~y with accurate location of all buildings, property lines, streets, and mmsual natural or
topographic features.
2. Final Approval from Health Dept. of water supply and sewerage-disposal (S-9 form).
3. Approval of electrical installation fi-om Board of Fire Underwriters.
4. Sworn statement from plumbcr certifying that the solder used in system contains less than 2/10 of 1% lead
5. Cowanercial building, industrial building, multiple residences and similar buildings and installations, a certificate
of Code Compliance from architect or engineer responsible for the buildiug.
6. Submit Planmng Bored Approval ofcompleled site plan requirements.
B. For existiug buildings (prior to April 9, 1957) nou-couforming uses, or huildings and "pre-existing" land uses:
1. Accurate survey of property showing all propelly lines, streets, building and nmlsual uatural or topographic
features.
2. A properly complcted applicalion and consellt to inspect sigmed by the applicant, if a Certificate of Occupancy is
denied, thc Buiidiug h~spccto~ shall state the ieasons therefor iix writing to thc applicant.
C. Fees
I Certificate ofOccupallt5 - Nex; dwelli~g $?5.00, ..\dditions to dwelling $25.00, Alterations to dwelling $25.00
Swinnning pool $25.00, AccessoJy building $2500, Additions lo accessory building $25.00, Businesses $50 00
2. Ce~Xificate o£Occupancy on Pit-existing Building $100 00
3. Copy of Ce~lificate of Occupancy- $25
4 Updated Certificate ol ()ccopallcy $5000
5. Temporary Certificate ofC)ccupancv - Residential $15 00, Conmae~cial $1500
Ne; Co astmction: Old or Pre-existing Building: L../ (check one)
Locationoferope,q.y: 2q~ ~(3 ~~ ~ ~¢~*~
House No. Street Hamlet
Owner or Owners of Prope,%,: ~~ ~ *~ ~ ~~
SHf'~lkC6untyTaxNlapNo 100(,,,ectio,l._~ ~ Blo;k ~/X~Lot___~ ~
Subdivis o ~ ....... Filed Map. Iot:
eem~it Nn. ~15~ ,)ate ofPemut, q-l~Og Applicant:_ ~*m
Health Dept. Approvak Unde]}vriters Approval:
Planning Board Approval:
Request fur: Temporary Ce~qficate
Fee Submitted: $___.
Final Certificate:
J (check one)
/A~plican{ Signature 6
FORM NO. 3
TOWN OF SOUTHOLD
BUILDING DEPARTMENT
Town Hall
Southold, N.Y.
(THIS
BUILDING PERMIT
PERMIT MUST BE KEPT ON THE PREMISES UNTIL FULL
COMPLETION OF THE WORK AUTHORIZED)
PERMIT NO. 34153 Z
Date SEPTEMBER 12, 2008
Permission is hereby granted to:
DOUGLAS JR & ORS ROGERS
PO BOX 265
EAST MARION,NY 11939
for :
INSTALLATION OF A WOODSTOVE PER INSTALLATION SPECS AS APPLIED FOR.
at premises located at
295 OLD ORCHARD LA
EAST MARION
County Tax Map No. 473889 Section 031 Block 0007
pursui~mt to application d~ted SEPTEMBER 10, 2008 and a~proved by
/
Building Inspector to expire on MARCH
Fee $ 200.00 /
021
~horize
ORIGINAL
Rev. 5/8/02
TOWN OF SOUTHOLD BUILDING DEPT.
765-1802
INSPECTION
[ ]FOUNDATION 1ST
[ ]FOUNDATION 2ND
[ ]FRAMING / STRAPPING
[ ]FIREPLACE & CHIMNEY
[ ]FIRE RESISTANT CONSTRUCTION
[ ] ROUGH PLBG.
[ ] INS~ULATION
[ i,,~NA L
[ ] FIRE SAFETY INSPECTION
[ ] FIRE RESISTANT PENETRATION
REMARKS:
DATE
INSPECTOR
OWNER
TOWN OF SOUTHOLD PROPERTY RECORD CARD
STREET
¥1 LLAGE
DIST. SUB. LOT
FARM Acre
~wampland ~ FRONTAGE ON WATER
douse Plot L DEPTH
Fotal DOCK
:O~E O ER ' N- ACRi
~ES.~:/~ S~SV VL FARM 'COMM.I ~/2-Z/~ ,,/"CB. MISC. Mkt. V. lue
~ND IMP. TOTAL [ DATE REMARKS ~l/~: - K
I I
V~. Bldg.
/ ,~/~'~Foundation
~ ~ II '1~.~/1/~ I I /
-- ~ III[11 IL'Ill ///11
I lff~l~l I~ql I/ ~
II ~~11 I~
I
I I I I,/111 II-I ~
Dinette
Floors ~ K.
Interior Finish .;:/ ? . '-' LR.
Heat DR.
'~tensJon
Extension
~orch
)orch
Breezeway
~arage
Patio
Total
7/?
/jc.3
Basement
Ext. Walls
Fire Place
Type Roof
Recreation Room
/L~ 7~ Dormer
Driveway
Rooms I st Floor
Rooms 2nd Floor
BR.
FIN. B.
APPRO,VE[~ AS NOTED
NOTIFY BUILDi .~ ...~Mc,-~ AT
765-1802 8AM ~,~'; FCRTHE
FOLLOWING ....
1. FOUNDATION - ~,vO REQUIRED
FOR, POURE~ C'~HORETE
2. ROUGH - FRAbli~4G & PLUMBING
3. INSULATION
4. FINAL - CONSTRUCTION MUST
COMPLETE F~F~ C.O,
BE
ALL CONSTRUCTIO~4 SHALL MEET THE
REQUIREMENTS O~TRE CODES OF NEW
YORK STATE. NO~ RESPONSIBLE FOR
DESIGN OR CONSTRUCTION ERRORS.
,/
COMPLY WITH ALL CODES OF
NEW YORK,~TAF
_ E & TOWN CODES
AS REQU~.~ -:.,*JD CONDITIONS OF
,--.--.____~ SOU~OLD TO~ ZBA
SOUTHOLD TOWN PLANNING BOARD
SOUTHOLD TOWN '"RUSTEES
,,r.s. ~c )CCUPANCY q:~
U~E IS UNLA~
~'iTHOUT CER¢ ~IF
':S..qbPANC f'~
/\
L
ICATE
½he own~.r ~nd ~o ~¢
Jetul F 400 USA
USA/CAN - Installation and Operating Instructions
2
J~l~r K',s~l~y s~'e these imtr~ctio~s ~r~re ~e~nces.
TOWN OF SOUTHOLD
BUILDING DEPARTMENT
TOWN HALL
SOUTHOLp; NY 11971
TEL: (631) 765-1802
FAX: (631) 765-9502
SoutholdTown. NorthFork.net
q/lZ-
Examined ,20__
Approved ,20
Disapproved a/c
Expiration
_%/mt, o/0
PERMIT NO.
BUILDiNG PERMIT APPLICATION CHECKLIST
Do you have or need the following, before applying'?
Board of Health
4 sets of Building Plans
Planmng Board approval
Survey
Check
Septic Form
N.Y.S.D.E.C.
Trustees
Flood Permit
Storm-Water Assessment Form
Contact:
Mail to:
Building Inspector
[~] ~(P [ 0~[~ [L~i Date % ~0~r-}0:~_0<~ ,20.
i [ / [ INSTRUCTIONS
/ ~L. DG. DEPT. I
t.' /O,WN~OF ,~,Q ~ 9 ] ........
a. 3,,ia avp ...... on l,~T~O[,~ COihpletely filled in by typewriter or in ink and submitted to the Building Inspector w~th 4
sets of plans, accurate plot plan to scale. Fee according to schedule.
b. Plot plan showing location of lot and of buildings on premises, relationship to adjoining premises or public streets or
areas, and waterways.
c. The work covered by this application may not be commenced before issuance of Building Permit.
d. Upon approval of this application, the Building Inspector will issue a Building Permit to the applicant. Such a permit
shall be kept on the premises available for inspection throughout the work.
e. No building shall be occupied or used in whole or in part for any purpose what so ever until the Building Inspector
issues a Certificate of Occupancy.
f. ~very building permit shall expire if the work authorized has not commenced within 12 months after the date of
issuance or has not been completed within 18 months from such date. If no zoning amendments or other regulations affecting the
property have been enacted in the interim, the Building Inspector may authorize, in writing, the extension of the permit for an
addition six months. Thereafter, a new permit shall be required.
APPLICATION IS HEREBY MADE to the Building Department for the issuance of a Building Permit pursuant to the
Building Zone Ordinance of the Town of Southold, Suffolk County, New York, and other applicable Laws, Ordinances or
Regulations, for the construction of buildings, additions, or alterations or for removal or demolition as herein described. The
applicant agrees to comply with all applicable laws, ordinances, building code, housing code, and regulations, and to admit
authorized inspectors on premises and in building for necessary inspections. ~t_.. 00
(Signature ~f app~ant or name, ifa corporation)
(Mailing address of applicant)
State whether applicant is owner, lessee, agent, architect, engineer, general contractor, electrician, plumber or builder
Name of owner of premises
(-_) ~ks on the tax roll or latest deed)
If applicant is a corporation, signature of duly authorized officer
(Name and title of corporate officer)
Builders License No.
Plumbers License No.
Electricians License No.
Other Trade's License No.
Location of land on which proposed work will be done:
oR.c- a0
House Number Street
County Tax Map No. 1000 Section
Subdivision
Hamlet
Block '~\ , -q - Z
Lot
Filed Map No. Lot
2. State existing use and occupancy of premises and intended use and occupancy of proposed construction:
a. Existing use and occupancy
b. Intended use and occupancx
3. Nature of work (check which applicable): New Building_
Repair Removal Den~olition
4. Estimated Cost O[~),~.~C:~XD,Cx52)
5. If dwelling, number of dwelling units
If garage, number of cars
Fee
Addition Alteration
Other Work c~C/oo0
(Description)
(To be paid on filing this application)
Number of dwelling units on each floor
6. If business, commercial or mixed occupancy, specify nature and extent of each type of use.
7. Dimensions of existing structures, if any: Front
Height Number of Stories
Rear
Depth
Dimensions of same structure with alterations or additions: Front
Depth_ Height. Number of Stories
8. Dimensions of entire new construction: Front Rear
Height Number of Stories
9. Sizeoflot: Front Rear Depth
Rear
10. Date of Purchase
Name of Former Owner
11. Zone or use district in which premises are situated
12. Does proposed construction violate any zoning law, ordinance or regulation? YES NO
13. Will lot be re-graded? YES __ NO__Will excess fill be removed from premises? YES__ NO__
14. Names of Owner of premises
Name of Architect
Name of Contractor
Address Phone No.
Address Phone No
Address Phone No.
15 a. Is this property within 100 feet of a tidal wetland or a freshwater wetland? *YES NO
* IF YES, SOUTHOLD TOWN TRUSTEES & D.E.C. PERMITS MAY BE REQUIRED.
b. Is this property within 300 feet of a tidal wetland? * YES __ NO__
* IF YES, D.E.C. PERMITS MAY BE REQUIRED.
16. Provide survey, to scale, with accurate foundation plan and distances to property lines.
17. If elevation at any point on property is at 10 feet or below, must provide topographical data on survey.
18. Are there any covenants and restrictions with respect to this property? * YES__
· IF YES, PROVIDE A COPY.
NO
STATE OF NEW YORK)
SS:
COUNTY OF )
being duly sworn, deposes and says that (s)he is the applicant
(Name of individual signing contract) above named,
CONNIE D. BUNCH
(S)He is the ~,.~..,., ~,.hli~. ~t. ~ Nm~u YArk
(Contractor, Agent, Corporate Of ricer, etc.) ,.v~., ~8.-6i[1115-~1~0~' L-
uua~ifled in 5ut~K uoumy_ ~.
Commission Expires April 14, 21)t-l-d~plSisa
of said owner or owners, and ~s' duly authorized' to perform or have performed the said work and to make and file plication;
that all statements contained in this application are tree to the best of his knowledge and belief; and that the work will be
performed in the maimer set forth in the application filed therewith.
Sworn to before me this_
Notary Public
- Si~natur~f Ap~'Iicant
/
USA/Canada
Installation and Operation Instructions for USA/CanadA
installation et fonctionnement pour Canada
Safety Notice: If this solid fuel room heater is not properly installed, a house fire may result. For your
safety, follow the installation directions. Contact local building or fire otficials about restrictions
and installation inspection requirements in your area. Kindly save these instructions fur future
reference.
Avis de s~curitO: Une installation non appmprfC, e de ce po&le de chauff-age risque de provoquer un
incendie. Assurez votre s~curit~ en respectant les directives d'installation suivantes. Consultez les
autorit~s locales du b~timent ou de la prC. vention des incendies au sujet des restrictions et exigences
relatives aux inspections d'installations dans votre r~gion.
Tested and listed by ITS, Intertek Testing Services, Middleton, Wisconsin.
Tested to U.S. Standards: ANSI/UL 737 and ANSI/UL r482, Canadian Standards: CAN/ULC-S627-Mg~ C--'~ ~'*~US
Standards
The J~tul F 400 woodstove has been tested and listed t~,
U.S. 5tandard~ ANSI/U L 737 and ANSI/UL 1482.
Canadian Standards: CAN/ULC-5627-M93
ITS, Iote~tek Testing Sendces, Middleton, WI
~anu~actured ~
Jetul AS, PJ~. Box ~411, F~drikstad, Norway
Distributed by:.
Jetul Nor~ America
55 Hutcherson Drive
Gorham, Maine o4o38, USA
This heater meets the U.S. Environment Protection Agency's
Emissions limits fur wood heaters manufactured and sold after
July 1,~990.
Under specific test conditions, this heater has shown heat output
at rates ranging from ~,3oo to 27,800 BIU's per hour.
Tlte Jetul F 400 woodstove is only listed to bum wood. Donor
bum any other fuels.
Read Ulis entire manual before you install and use your
room heater.
Save these i,Dbuctions and make them available to anyone using
or sewtcing the stove.
J~tul North America
55 Hutcherson Drive
Gorham, Maine o4o38
USA
Check Building Codes
When installing, operating and maintaining your Jetul F 4oo
woodstove, followtfle guidelines presented in these instructions,
and make them available to anyone using or servicing the
stove.
Your ci~,town,county or province may require a building permit
to install a solid fuel burning appliance.
In the U.S.,the National Fire Protection Association's Code, N FPA
2~1, Standards fur Chimneys, Fireplaces, Vents and Solid Fuel
Burning Appliances, or similar regulations, may apply to the
installation of a solid fuel burning appliance in your area.
In Canada, the guideline is established by the CSA Standard,
CAN/CSA-B365-M93, Installation Code fur Solid-Fuel-Burning
Appliances and Equipment.
Always consult your local building inspector or antho~ity having
jurisdiction to determine what regulations apply in your area.
NATIONAL We suggest that our woodbuming hearth
#*:,,.u~t products be installed and semced by
professionals who are certified in the U.S.
by the National Rreplace Institute' (NR) as
NFl Woodbuming Specialists or who are
certified in Canada by~'~asm'~a'~r,~
CERTIFIED Wood EnergyTechnical
~ Training (WE'I-13. ~ .............. ,
Accepted For Use
City of New York
Department of Buildings
MEA 313-00-E
J~tul North America, Inc.
.letul pursues a policy oj~ continual product development. Products as supplied may therefore d~er in specification, colour, or ~ype
accessories~j~rom those illustrated or otherwise described in publications and brochures.
Table of Contents
1o0 Installation
1.1 Assembty Before Installation ....................................3
1.2 Flue Collar Reversal .............................................. 4
1.3 Chimney Connector .................................................... 4
a.o Chimney Requirements
2.1 Masonry Chimneys .................................................... 4
2.2 Prefabricated Chimneys .................................................. 5
2.3 Chimney Height ............................................................... 5
2,4 Wall Pass-Throughs ................................................. 5
3.o Connecting to the Chimney
3-~ Masonry Chimney ........................................................... 6
3.2 Hearthmount / Fiteplaces .............................................. 6
3.3 Prefabricated Chimneys ............................................. 6
4.0 Clearances to Combustibles
4.1 Floor Protection ............................................................... 6
4.2 Clearances to Wails and Ceilings ............................ 6
4*3 Using Shields to Reduce Clearances ........................... 6
4-4 Alcove Installation .................................................. 7
4-5 Mobile Home Installation ............................................ 7
S.o Operation
5.1 Use Solid wood Fuel Only .............................................. 7
5-2 Controls .................................................................. 7
5-3 Break-in Prncedure .................................................... 7
5-4 Starting / Maintaining the Fire ......................................... 8
5-5 Adding Fuel ...................................................................... 8
6.0 Maintenance
6.r Ash Removal ..................................................................... 9
6.2 Glass Care ......................................................................... 9
6.3 Glass Removal .................................................................... 9
7.0 General Maintenance
7.1 Gaskets .............................................................
7.2 Gasket replacement .....................................................
7.3 Chimney System .............................................................
8.0 Accessories
8.1 Firescreen ..................................................................... lo
8.2 Stove-top Thermometer .................................................. lo
8.3 Outside Air Kit .................................................................. ro
8.4 Floor Bracket Kit ............................................................. 11
8.S Pear Heat Shield ................................................................. rr
8.6 Bottom Heat Shield ......................................................... rr
9-0 IIl~r~;.,o~ons
Clearance Diagrams .................................................................... 12
Clearance Chart ................................................... 13
Figures ............................................................................................ 14 - 16
Parts Diagram and Ust ............................................................... 17-r8
Appendix A - Alternate Floor Protection ......................... 18
USA/Canada
Safety Notices
Bum solid wood fuel oflly.
Do not ose chemicals or fluids to start the tim. Do not bum
ga~oage or flammable fluids.
If this room heater is not property installed, a house fire
may result. To reduce the risk of fire, follow the installation
instructions. ~ilure to follow these instructions may result
in property damage, bodily injmy, or loss of life.
Contact the local buiMing or fire officials about restrictions
and installation inspection requirements in your area.
Do not connect this stove to any air distribution duct or
system.
Extremely hot while in opemtimtl Keep children, dothin8
and furniture away. Contact will cause skin bums.
Avoid creating a Iow pressure condition in the room where
the stove is operating. Be aware that operation of an
exhaust fan or clothes d~yer can create a Iow pressure area
and consequently pmmote flow reversal through the stove
and chimney system. In some cases, the optional Outside
Air Kit ~54335 can he used to alleviate this condition. The
chimney and building, however, always work together as a
system - provision ofoutside air, directly or indirectly to an
atmospherically vented appliance will not guarantee pmper
chimney performance. Consult your local Jetul authorized
dealer regarding specific installation/performance issues.
Jetul recommends that this stove be iestalled by a professional
solid fuel technician or thatyou cra~sult one if you dothe work
yourself. Also, consult your insurance company regarding any
other specific requirements.
Installation
ff this solid fuel room heater is not properly installed, a house
fire may result. Foryour sefoty, fuliow the installation directions.
Contact the local building or fire officials about restrictions and
installaUon inspection requirements in your area.
Your local officials have final authority in determining if a
proposed installation is acceptable. Any requirement bythe local
authority having jurisdiction that is not specifically addressed in
this manual, defaults to NFPA 2~, and Incal codes in the U.S. or in
Canada, CAN/CSA-B365-M and local cedes.
1.1 Assembly Before Installation
Unpack the Stove
Inspect the stove for damage. Contact your dealer immediately
if any damage is found. Do not install the stove If any damage
is evident.
· Inspection Cover (Not for use in US/Canada)
· Door Handle
· Hardware Bag
Brick or modular block must be a minimum of 4" (lO cm)
nominal thickness. Stone construction must be at least r2"
(3o cm) thick.
A newly-built chimney must conform to local codes, or, in
their absence, must comply with national regulations.
An existing chimney must be inspected by a professional
licensed cblm ney sweep, fire official, or code officer to ensure
that the chimney is in proper working order.
No other appliance may be vented into the same flue.
An airtight clean-oat door should be located at the base of
the chimney.
2.2 Prefabricated Chimneys
A prefabricated metal chimney must be tested and listed for
use with so//d~fue/lmmi~g eppl/gnces. High Temperature (FIT)
Chimney Standard UL ro3 for the U.S. and High Temperature
Standard ULC S-629 for Canada.
The manufacturer's installation instructions must be followed
precisely. Always maintain the proper clearance to combustibles
as established by the pipe manufacturer. This clearance is usually
a minimum of 2~, although it may vary by manufacturer or for
certain chimney components.
2.3 Chimney Height
The chimney must be at least 3 feet (92 cm) higher than the
highest point where it passesthrough the roof and at least 2 feet
(61 em) higher than the highest part of the roof or structurethat
is within lo feet (3.05 m) of the chimney, measu~l horizontally.
See figure 3.
Chimneys shorter than ~4 feet (4.z7 m) may not provide adequate
draft. Inadequate draft can result in smoke spillage when loading
the stoke, or when the door is open. Poor draft can also cause back
puffing (ignition af gas build-up insidethe firebox) and sluggish
performance. The mini mum height does not, in itself, guarantee
proper chimney performance.
Excessive chimney height can promote over-strong draft resulting
in high stovetemperatures and short burn times. Excessive draft
can be corrected by instaliin8 a butterfly damper. Your J~atul dealer
is an expert resource to consult regarding draft issues or other
performance-related questions.
USA/Canada
· The Pass-through must be at least r8" (45-7 cm) from
combustible ceiling materials.
· it will be necessary to cut wall studs, install headers, and
construct a sill frame to maintain the proper dimensions and
to support the weight of the brick.
· The bricks must be solid brick with a minimum of 3 fh inches
thick (nominal4"/to2 mm).
· Refractmy mortar must be used at thejunction ofthe chimney
and the pass-through liner. The pass-through liner must not
penetrate the chimney liner beyond the inner surface of the
chimney liner. Use extreme care when constructing the hole
in the chimney liner as the tiles can shatter easily.
In Canada
The installation must conform to CAN/CSA-B365, Instollofion
Code .for Solid Fuel Burning Appliances and Equipment. Before
proceeding be sure to consult your local building inspector.
Common Method:
· This method requires the removal of all combustible materials
from at least 18" (45-7 cm) around the chimney connector's
proposed location. A 6~ round liner requires a minimum
opening 43' x 43' (~o9.2 x ro9-2) square.
Locate the pass-through at least rr from combustible ceiling
materials.
· The space that is cleared of combustible materials must
remain empty. Sheet metal panels can be used to cover the
area. However, when using a panel on both sides of the wall,
each cover must be installed on noncombustible spacers at
least r"from the wall. If one panel of sheet metal is to be used
it may be installed flush to the wall.
See sectfon 5.3.1 and 5.3.z of CANICSA- B365-Mg~. Consult your
local building inspector, authorized ~tul Dealer, NFPA 211 in the
U.S. or CAN/CSA-B635 in Canada for other approved wall pass-
through methods.
2.4 Wall Pass-Throughs
In the U.S.
The National Fire Protection Association's publication, NFPA
2ri, Standard for Chimneys, Fireplaces, Vents and Solid Fuel
Burning Appliances permits four methods for passing through
a combustible wall. Before proceeding with any method be sure
to consult with your local building officials to discuss any local
code requirements.
Common Method:
See figures 4 and 5. Remove all combustible materials from
the pass-through area ( around the chimney connector), a
minimum 12" (30.5 cm). A 6" (15.2 cm) diameter connector
will require a 3r'x 3r~ (78.7 x 78.7 em) square opening.
The opening must be filled with at least r2~ (3o.5 cm) of
brick around a fireclay liner. The liner must be ASTM C35 or
equivalent, having a minimum wall thickness of 5/r (16 mm).
USA/Canada
1.2 Flue Collar Reversal
The Flue Collar is oriented in the Top Exit position. If a Rear Ex*~
position is required, remove the two mounting hoits, and turn
the collar rgo degrees. Secure the collar using the same bolts,
nuts and washers.
~.3 Chimney Connector
Use 6'single wall or listed 6'double-wall stovepipa to coonect the
stove to the chim ney. Single wall stovepipe must be black iron or
stainless steel and have a minimum thickness of 24 gauge. Do not
use aluminum or galvanized steel pipe for chimney connection
- these materials are not suitable for use with solid fuel.
Follow these guidelines regarding chimney connector
construction:
Do not use chimney connector as a chimney. It is intended
only for use as a connection device.
Each connector section must be oriented with the male
(crimped) end pointing toward the stove. See fig. a.
Secure all connector joints with three sheet metal screws.
For the best performance, the chimney connector should be
as short and di~*-t as possible, including no more than two
90' el bows.
The maximum vertical nm of single wall stovepipe should not
exceed lo ft. (3o5 crn). The maximum horizontal run should
not exceed ~ ft. (92 cra) with a ~14' rise per foot.
No part of the chimney connector may pass through an attic
or roof space, closet or other concealed space, or through
a floor or ceiling. All sections of the chimney connectors
must be accessible for cleaning. Where passage through a
wall or partition of combustible construction is desired, the
installation must conform with NFPA ~1~ or CAN/CSA-B365,
and is also addressed in this manual.
Do not connect this stove to a chimney flue sewicing another
appliance,
2.o Chimney Requirements
There are two types of chimneys suitable for the J~tul F 400:
1. A code-approved masons, chimney with a ceramic tile or
listed steel flue liner.
2. A pr~Cabricated chimney complying with the requirements
for Type HT (2~oo°F) chimneys per UL ro3 or ULC $629.
The chimney size should not be less than the cross-sectional area
of the flue collar, and not rnme than three times greater than the
cross-sectional area of the flue cellar.
When selecting a chimney typo and the location for the chimney
in the house, keep th is in mind: It is the chimney that makes the
stove wodc, not the stove that makes the chimney wodc This is
because a chimney actually creates a suction, called 'draft' which
pulls air through the stove.
Several factors affect draft: chimney height, cross-sectional area
(size), and temperature of the chimney, as well as the proximity
of surrounding trees or buildings.
A short masonry chimney on the exterior of a house will give
the poorest performance. This is because it can be very difficult
to warm the chimney thereby creating inadequate draft. In
extremely cold climates, it may be necessary to reline the chimney
or extend its height to help establish draft.
A tall, interior masonry chimney is easier to keep warm and will
perform the best under a variety of weather and environmental
conditions.
The fo#owing guidelines give the necessary chimney requirements
based on the national code (ANSI-NFPA 21r for the US. And CSA
CAN-B365 for Canada). However, many local codes differ from
the national code to take into account climate, altItude, or other
factors. Your local building inspector is the final approving
authority. Consult them prior to installation.
Do not connect the stove to any air distribution duct or
system.
Masonry Chimneys
When installing the J~tul F 400 into a masonry chimney you
must conform to all of the following guidelines:
The chimney flue size should not be less than the cross-
sectional area of the stove flue collar.
The cross-sectional area of the flue of a chimney with no
walls exposed to the outside below the roofline shall not be
more than three times the crosssectional area of the stove
flue collar.
The cross-sectional area of the flue of a chimney with one or
more walls exposed to the outside below the mofline shall
not be more than two times the cross-sectional area of the
stove flue collar.
Larger chimney flues should be relined with a listed or
codeapproved line~.
The masonry chimney must have a fireclay liner or equivalent,
with a minimum thickness of 5/8~ (14 mm) and must be
installed with refractory mortar. There must be at least lla~
(12.7 m m) air space between the flue liner and chimney wail.
The fi~clay flue liner must have a nominal size of 8n X r (2o
cm x 2o cm), and should not be larger than 8~X r2' (2o cm x
3o cm). A round fireclay liner must have a minimum inside
diameter of 6~(r5 cm) and maximum inside diameter of r (2o
cm).A larger chimney should be relined with an appropriate
code approved liner.
USA/Canada
3.o Connecting to the
Chimney
3.1 Masonry Chimney
When installing a Jetul F 400 into a masonry chimney through
a ~thimble' (the opening through the chimney wall to the flue),
the thimble must consist of ceramic tile or steel and be securely
cemented in place.
The chimney connector/stove pipe must slide completely inside
the thimble to the inner surface of the flue liner. It may be
necessaryto make use of a thimble sleeve (a pipe with a slightly
smaller diameter than standard stove pipe). See figure 5-
The con nector pipe or thimble sleeve must not protrude into the
flue liner or otherwise restrict draft.
Use refractory cement to seal the seam between the chimney
connector, sleeve, and thimble.
Do not connect this stave to a chimney flue se~icin8 another
appliance of any kind.
3.2 Hearthmount into a Masonry
Fireplace
The Jetul F 400 may be installed into a masonry fireplace
provided the height of the opening is a minimum of 29 ~/2~- Use
of the Short Leg Package will reduce the stove height by 2 ri4"
(57 mm).
Building code requires that the fireplace damper plate be removed
or secumlyfixed in the open position. A connector pipe must then
extend from the stove's flue exit through the damper area of the
fireplace and into the chimney tile liner. See fi&mm 6.
The inside area of the flue liner must not be less than the area of
the stove flue collar and cannot be more than three times greater
than the cross sectional area of the stove flue collar.
If the chimney liner is too large to accommodate the stove, an
approved relining system must be installed to msize the flue.
A now sheet metal damper block~ff plate must be_installed
arou nd the connector pipe at the damper frame a nd sealed with
the proper sealant (usually High-Temp Silicone).
3-3 Prefabricated Chimneys
When connecting the J~tul F 400 to a prefabricated metal
chimney always follow the pipe manufacture's instructions and
be sure to use the components that are required. This usually
includes some type of 'smoke pipe adapter~ that is secured
to the bottom section of the metal chimney and allows the
chimney pipe to be secured to it with three sheet metal screws.
See figure 7-
4.oClearancetoCombustibles
4.1 Floor Protection (For both U.S. and
Canada)
The J~tui F 400 requires one of the following three forms of
hearth protection:
Any UL, ULC orWH listed hearth board.(No bottom heat shield
required).
2. Any noncombustible material that has a minimum
R- value of 2.o. (No bottom heat shield required.)
3- Any noncombustible material with the use of the stove's
bottom heat shield.
All forms of protection must include a noncombustible surface
extending a minimum of r6" for U.S (460 mm for Canada) in
front of the stove, and 8" (2oo mm) from the sides and back of
the stove (measured from side and back panels).
This will ~sult in a minimum floor protection of 42'W X 44"D.
See figure 8.
in a rear vent installation, the floor protection must also extend
under the stove pipe a minimum of 2" (50 mm) beyond either
side of the pipe. See figure 8.
Consult appendix A at the back of this section for alternate floor
protection methods and materials.
4.2 Clearances to Walls and Ceilings
The clearances listed and diagramed in this manual have been
tested to U L a nd ULC standards and are the minimum clearances
to combustible materials specifically established for the J~tui F
400.
A combustible surface is anything that can burn (i.e. sheet rock,
wall paper, wood, fabrics etc.). These surfaces are not limited to
those that are visible and also include materials that are behind
noncombustible materials.
If you am not sure of the combustible nature of a material, consult
your local fire officials.
Remembe~."Fire Resistant"materials are considered combustible;
they are difficult to ignite, but will burn. Also "Fire-rated~ sheet
rock is also considered combustible.
Contact your local building officials about restrictions and
installation requirements in your area.
See pages 8-9 for complete clearance requirements and
diagzams.
4.3 Using Shields to Reduce Clearances
Chimney Connector Heat Shields: Use only connector heat
shielding listed for use with solid fuel heaters. The connector
heat shield must begin l~above the lowest exposed point of the
connector pipe and extend vertically a minimum of 25~ (64o cm)
above the top surface of the stove.
Double Wall Connectoe. Usted double wall pipe is an acceptable
alternative to connector pipe heat shields.
WalI-Moonted Protection: When reducing clearances through
the use of wall mounted protection:
In the U.S. rear to NFPA zn, Standard j~or Chimneys, Fireplaces,
Vents and Solid Fuel Burning Appliances, for acceptable
materials, proper sizing and construction guidelines.
In Canada, re, er to CAN/CSA-B36~, Installation Code ~or Solid-
Fuel Burning Appliances and Equipment, also for acceptable
materials, proper sizing and construction guidelines.
StoveMonrd0ed Heat shield: Rear Heat Shield ~4~54385 is approved
for use with the J~atul F 400 in the US. and Canada. No ether heat
shield nmy he used.
Notice: Many manufacturers have developed woodstove
accessories that permit clearance reduction. Use only those
accessories that have been tested byan independent laboratmy
and carry the laboratory's testing mark. Be sure to follow all of
the manufacturer's instructions.
4-4 Alcove Installation
The Jetul F 400 can be installed in an Alcove as diagrammed in
figures 9 and
r. The stove must be installed with listed double wall pipe.
2. In a protected alcove installation both side walls and rear
wall must be protected per N FPA art or CAN/CSA-B365. The
wall protection must be elevated r~ (z5 mm) from the floor
and spaced at least 1~(25 mm) offthe combustible wall, using
noncombustible spacers, to allow for air circulation behind
the shield.
3. The height of the wall protection including the bottom air
space must be 4r (121 cm).
4. The Bottom Heat Shield is required in all Alcove
installations.
5- Alcove floor protection must consist of a UL/ULC or WIll listed
hearth pad or a non combustible material with a minimum
R value of 2.o.
6. Minimum ceiliog height in an unj~lectodinstallation, olfthe
top of the stove is 5r(r48 cm).The minimum ceiling height
off the top of the stove in a protected ceiling installation is
36 (9r.5 cm).
4-5 Mobile Home Installation
The J~tul F 400 has been approved for use in mobile homes in
the U.S. and Canada with the following stipulations:
r. The stove must be secured to the floor of the mobile home.
Use Floor Bracket Kit ~75o3o4.
2. The stove is provided outside alt for cam bustion. Outside Air
Kit ~54335 (see page r6 for more details).
3. Use only listed double-wall pipe for the chimney
connection.
4. The stove must be grounded to the mobile home chassis.
5- The stove must othenNise be installed in accordance to ~4CRR,
Part 3;~8o (HUD).
Consult with your local building inspector or fire officials about
restrictions and requirements in your area, prior to installing
the stove.
Wamingl
Do not install this stove in a bedroom/sleeping room. Do not
installthe stove in any way tttat miBht compromise the structural
inte&Mty of the mobile home floor, walls, ceiliog, or roof.
USA/Canada
5.o Operation
Iqease read the following section completely, before building a
fire in your new Jetul F 400.
5.1 Use Solid Wood Fuel Only
First th is stove is designed to burn natural wood only. Wood that
has been air-dried for a period of 6 to r4 months will provide the
cleanest, most efficient heat.
'Coal
'Garbage
'Cardboard
*Solvents
'Treated or painted wood
*Chemical Chimney cleaners
*Colored paper
*Any synthetic fuel or logs
The burning of any of these materials can result in the release
of toxic fumes. Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liquids to start or
"freshen-up' the fire. Always keep such liquids away from the
heater at all times.
Important: Never build or allow the fire to rest directly on the
glass panel. The logs should always be spaced at least one inch
from the glass to allow for proper air flow within the firebox.
5.2 Controls on the Jetul F 400
Combustion air is controlled by the Primary Air Lever, located
above the ashlip on the front of the stove. The lever actuates a
shutter over the air inlet which regulates the volume of primary
air entering the firebox and affects heat output and burn time.
When ~fiat stortfn9 or ret/v/ag the~qre, the prfnm~y control/ever
shou/d be et their ~fght Positron, which allows the maximum
amount of air into the stove. The greater the amount of air
enteringthe stove, the hotter and faster thefirewill bum. Mrna*ag
the/ever to the/e~ reduces the aidlow into the stove which
prolongs the fire at a lower heat output. See figure 11.
Air Flow / Performance
Primary air enters the firebox directly above the glass panel on
the door. The incoming air creates a turbuleot barrier or"airwash'
between the glass and the fire. Reducing the flow of primary air
directly reduces the effectiveness of the airwash. Determining
the primary air setting for the best overall performance for your
particular needs and installation will only be established over
time through trial and error.
5.3 Break-In Procedure
The Jetul F 400 is constructed of cast iron and stove furnace
cement. This type of construction requires the stove to be
"broken-in~ gradually so that heat expansion does nut occur
too quickly and cause damage. The following steps describe the
proper break-in procedure for the Jetul F 400:
r. Light a small fire of newspaper and kindliog. Only allow the
stoveto reach a maximum surfacetemperature of 2oo°F {g3°
C). Burn for approximately r hour.
~. Allow the stove to cool to room temperature.
3. Ught a second fire, allowing the stove to reach a maximum
temperature of 3oo°F (r49°C) for ~ hour.
4. Cool the stove to room temperature.
USA/Canada
5- Ught a third fire and gradually allow the stove to reach a
sun'ace temperature of 4oo°F (2o4'C).
6. Cool stove to room ternperatum. This completes the"break-in"
procedure.
To monitor the stove's tempecatum, use a magnetic stove-top
thermometer, placed directly on the corner of the stove's top
plate.
Note: Keep the stove under 4oo"F (2o4°C) surface temperature
during any "break-in tim", with the exception of the last"break-
in" fire. If the temperature exceeds 4OO°F, move the primary
air control lever all the way to the left to shot off the air supply
completely, it is normal that the stove top temperature will
continue to climb until the fuel burns down somewhat. Once
the tim is oot and the stove has cooled to room temperature,
continue the break-in procedure. Never attempt to reduce the
temperature by removing buming logs from the fire.
Note:/t is normal for a new painted stove to emit an odor and
smoke during its first several fires. This is caused by the seasoning
of the high temperature paint and will diminish with each fire.
Opening a window or door to provide additional ventilation will
alleviate this condition.
5-4 Starting and Maintaining a Fire
Burn only solid wood directly on the bottom grate of the stove.
Do not elevate the fire in any way.
The ash pan door oo the stove must aheays he securely dosed
when the stove is in operation.
Buming the stove with the Ash Door open will over-fire the
strum and cause interior damage.
r. Writh the primary air controi lever in the full open position (to
the right), start with several sheets of crumbled newspaper
placed directly on the grate. On top of the newspaper, place
several pieces of small dry kindling (approx. r" in diameter)
with two to th me larger logs (approx. 3"to 5" in diameter) on
top.
a. Ught the fire and close the door, slowly building the fire by
adding larger and larger logs. Be sure to follow the break-in
procedure before creating a hot fire that might damage the
3* Once the stove has reached a surface temperature range of
between 4oo' and 6oo', (2o4'C -3r6'C), adjust the primary
air control leveras necessary to generate the heat outpot and
burn time desired.
Jetul recommends use of a magnetic stove top thermometer
to monitor the surface temperature of the stove. The
optimum surface temperature range for the most effldent
bum is between 400' and 6oo' (2o4°C ~316°C).
See figure ra for the best locations to place a stove-top
thermometer.
Never o~.r~fre the stove. ~ any part o~ ~ne stov~ or chimney glo~
you are over~r~ng. A house ~lre or serlous domege to the stove or
chimney could result. If t~ls condition occurs, immediately dose
down the air eontrol.
5.5 Adding Fuel
When reloading the stove while it is still hot and a bed of hot
embers still exist, followthis reloading procedure:
Always wear 8loves when tending to the stove.
Push the air control lever to the full open position (far
~ght).
Wait a few seconds before opening the door.
Use a stove tool or poker to distribotethe hot embers equally
around the firebox.
Load the fuel, usually with smaller logs first.
Close the door, he sure to latch the door tightly.
Wait 5- ~o minotes before adjusting the primary air to the
desired heat ootput setting. (If you have at least a 2"thick
ember bed when reloading, it may he possible to dose the
door and immediately adjust the air control setting).
Creosote and Soot Formation and the Need
for Removal
When wood is burned slowly, it produces tar and other organic
vapors which combine with expelled moisture to form creosote.
These creosote vapors condense in the relatively cool chimney
flue of a slow burning fire. The creosote that accumulates in
the flue is highly flammable and is the fuel of chimney fires.
To prevent a chimney fire, the creosote needs to be removed
by sweeping the chimney and flue connector. The frequency of
sweeping will depend on how you operate your stove, bot it is
important to inspect the flue after every two weeks of use. An
accumulation ofr/4"o~ more on the sides of the flue or connector
is considered hazardous and should be removed.
In the event that creosote in your chimney or flue connector
ignites,the resulting fire is often accompanied by a roaring noise
and a crackling sound as flakes of burned creosote break loose. If
you suspect you are having a chimney fire, immediately close the
draft regulator and make sure the stave door is closed. Call the
fire department and get everyone safely out of the house.
Trying to extinguish the fire in the stove will not help. In f~ct it
can make the matter worse by allowing oxygen through the door,
which then supports the fire in the chimney. When the roaring
and cracklin8 has stopped, you should resist the temptation to
open the door and look at the fire. The fire may have suffocated,
but could rekindle when you open the door. After a chimney fire,
do not use your stove until the chimney aed the flue connector
has been cleaned and inspected to ensure that no damage has
been sustained.
6.o Maintenance
6.1 Ash Removal
For your pmtectioo always wear safety gloves when handling
the ash pan.
Ash removal will be required periodically depending on how
frequeotly the stove is used. The JOtul F 400 is equipped with an
exterior ash pan assembly that allows easy ash removal w~thout
opening the froot door.
The ash pan door is k~cated under the front ashlip of the stove.
To open the ash door, rotate the door knob couoterclockwise to
unlatch the door and clockwise to latch the door.
With a 81oved hand, grasp the ash pan handle and remove the
ash pan. Always close the ash pan door before leaving to dispose
of the ashes.
The ashes should be placed in a metal container equipped
with a tight sealing lid. The container should be placed on a
noncombustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally dispersed, they
should be retained in the closed cootainer uotil all cinders have
thoroughly cooled.
6.2 Glass Care
Cleaning
On occasion it will be necessary to clean the carbon deposits
and fly ash off of the glass, if the carbon and fly ash are allowed
to remain on the glass for an extended period of time it could
eveotually cause the glass to become etched and cloudy. Any
creosote that might develop on the glass will burn off during
the next hot fire.
Follow this cleaning procedure:
1. Glass needs to be comp/efe/y coo/.
2. Only use a cleaner that is specifically desigeed for this purpose.
The use of abrasives will damage the glass and ultimately
leave the glass frosted.
3* Rinse and d~ glass completely before burnlng the stove.
Cautionl Always operate the door slowly and carefully to avoid
cracking or breaking the glass. Never use the door to push wood
ioto the firebox, fi:the glass becomes cracked or broken follow
the reptacemeot procedum below. Never operate the stove w/th
o cmcked or brokeo glms penel.
Importaot: Replace glass only with ceramic glass panel specifically
designed for the J~tul F400. Do not use substitutes. Replacemeot
glass is available from your local JlatuI dealer.
USA/Canada
6.3 Glass Removal
r. Remove the door from the stove and place on a fiat surface.
2. Carefully remove all of the glass clips from the inside of the
door.
3* Gently remove the glass panel and gasketing.
4* Using a wire brush, remove all remaining debris from the
glass area.
5- Apply a small bead of gasket/stove cemeot and the new
gasket. Do not overlap the ends of the gasket rope.
6. Ceoter the new glass panel over the gasket and reinstall the
glass clips. See figure
7- itmaybenecessaqltoretightentheglassclipsafterthestove
has be bumed and the gasketing has been seated.
Imlx~tant: it is extremely importaot to tighten the glass clips
slowly and in an alternating pattern as you would tighten the
lugs on an automobile wheel.
6.4 Chimney System
The J~atul F 400 is designed to burn cleanly and efficieotly when
used according to the guidelines in this manual. In order to
maiotain proper performance, you should inspect the chimney
and chimney connector at the beginning of each heating season
and then, twice a mooth during the heating season. Clean the
chimney whenever creosote and fly ash accumulation exceeds
1/4 inch in any part of the system.
Chimney brushes are available from your local J~atul dealer
or hardware supply store. Your dealer can also refer you to a
reputable, pre~ssional chimney sweep who will have all the
equipment to ensure a complete and proper job. Failure to keep
the chimney system flee of creosote and build up could result in
a serious chimneyfire.
USA/Canada
7.o General Maintenance
As with your car, regular maintenance will prolong the life ofyour
stove and ensure satisfac~my performance.
Enamel Care:.
DO NOT ATTEMPT TO CLEAN HOT ENAMEL SURFACES. Clean
only cold enamel surfaces with a soft damp cloth and polish
with a clean dry cloth.
DO NOT USE SOAPY OR ABRASIVE SOLUTIONS. These can cause
stains. Coffee, tea, and fruit jucies will also cause stains.
Avoid contact with metal objects. Trivets, kettles, or pots, can
damage the enamel.
Empty stove of all soot and ashes. Only use a vacuum for this
job if the vacuum is specifically designed for ashes.
Inspect the stove seams. Use a utility light to inspect the stove
inside and out for cracks or leaks. Replace all cracked parts
and repair any cement leaks with furnace cement.
7.1 Gaskets
Chock door and glass panel gaskets for tightness. To check the
seal of the front door, close and latch the door on a dollar bill and
slowly try to pull the dollar bill free. If it can be easily removed,
the seal is too loose. Chock several spots around the door, and
repeat the procedure on the ash pan door as well.
7.2 Gasket Replacement
r. Use pliers and a putty knife to remove the old gasket from
the door.
2. Thoroughly clean the channel with a wire brush.
3- Apply a small bead of cement to the channel.
4- Gently press the new gasket into the cement to seat it in the
channel. Close and latch the door and then reopen. Wipe a ny
excess cement squeezed out from around the gasket.
Gasket List for the J~tul F 400
Description Size Leogth
Top Plate Gasket 3/8' LD 7
Smoke Outlet Gasket 3/16~ LD/SA 3'
Ash Housing Gasket 3/16" LD/SA 4'
Ash Door Gasket 5h6" LD 4'
Glass Gasket 3/8" LD 5'
Door Gasket 5h6" LD 5,8'
7-3 Chimney System
The J~tul F 400 is designed to burn cleanly and efficiently when
used according to the guidelines in this manual. In order to
maintain proper pen~ormance, you should inspect the chimney
and chimney connector at least twice a year and clean when
creosote and fly ash deposits exceed 1/4"in any part of the system.
Failure to keep the chimney system flee of creosote and build up
could result in a serious chimney fire.
8.o Accessories
Use only accessories that are specifically designed for use with
the Jetul F400.
8.1 Firescreen (# 2965o)
The J~tul F 400 has been approved for use as an open fireplace,
with front door open. Care should be taken when operating the
stove as a fireplace.
Always have the Firescreen in place, attached to the stove
Never ovedoad the stove. For the best appearance, burn logs
in the traditional three log configuration.
When you operate the stove with the screen in place,
efficiency is sacrificed for the sake of aesthetics, much as with
a conventional fireplace. Wood will burn at a much faster rate
as combustion air is uncontrolled. Most of the heat value of
the wood will he lost up the chimney.
Nut all installations will support the use of the firescreen.
Moderate o~ Iow draft conditions may result in smoke spillage
from the stove when using the fi~escreen.
Wamin~ Operateyour .l~tul F400 with the front deor fully open
and the flrescreefl in place or fully closed. A partially opened door
may result in eve~dng. Also, if the door are left: parUy open,gas
and flame may be drawn out of the stove opening, cleating risks
from both fire and smoke.
8.2 Stove-Top Thermometer (# 5oo2)
Jetul recommends the use of a magnetic stove-top thermometer
to monitor the surface temperature of the stove. The optimum
surface temperature range for the most efficient, clean burn is
between 400' and 6oo'.
8.3 Outside Air Kit (# 54335)
You r local buildin8 code may require that an outside air supply be
connected to the stove. J~tul Outside Air Kit 154335 must be used
in these installations unless otherwise specified by the local code
official. While the use of outside air may be beneficial in some
installations, in itself, such a system does not guarantee proper
chimney performance.
The Outside Air Kit includes an adapter collar to attach the air duct
to the stove. Installation will require these additional materials
not included in the kit:
1. 3" (8o mm) diameter flexible metallic Air Duct - ofappropdate
length to reach from the stove to the outside of the house.
2. Weatherproof Duet Cap for the duct termination on the
outside of the house.
3- Rodent Screen ' no larger than 1/4~ {5 mm)mesh-
Outside air should be considered iff.
r. The stove dees not 'draw' steadily. Smoke rollout occurs when
the door a re opened. Fuel burns poorly. Backd rafts occur with
or without a fire burning.
2. Other fuel-fired equipment in the house, such as fireplaces
or other heating appliances, smell, do not operate properly,
suffer smoke mil-out when opened, or back-d raft whether or
nut there is combustion present.
3. Opening a window slightly on a calm (windless) day alleviates
anyofthe above symptoms.
4. The house is equipped with a well-sealed valxw barrier and
tight fitting windows and/or has any powered devices that
exhaust house air.
5- There is excessive condensation on the windows in the
winter.
6. A ventilation system is installed in the house.
If these or other indications suggest that infiltration air is
inadequate to supply sufficient air for the stove, additional
combustion air should be provided from the outdoor. Outside
combustion air can be provided tothe appliance bythe following
means:
1. Direct connection: The J~tul F 400 has been tested and
approved for use with the outside air kit listed above.
2. Indirect method: Outside air is ducted to a point no closer
than (~2~) 3oo mm from the stove, to avoid affecting the
performance of the appliance.
3. A mechanical ventilation system:If the house has a ventilation
system (air change or heat recoven~):
a. The ventilation system may be able to provide sufficient
combustion makeup air for the solid-fuel appliance.
b. The homeowner shoold be informed that the ventilation
system might need to be rebalanced by a ventilation
technician after installation of the appliance.
Note:. Provision o~ outside air to tile stove, directly or iedlredt~
may j~il to remedy the problems outlined above. Chimney
per~ornmnce is determined by e verlety oJ~ interelutlng ~ectors
which may not be e~OLKted by the air suDpl~ Your local Mtul
authorized dealer is your best resource ~or in~ormetion re(jord lng
chimney end stove pertinence issues.
USA/Canada
8.4 Floor Bracket Kit (# 750304)
Use of the Floor Bracket Kit is required in all mobile home
installations to secure the stove to the floor. Complete installation
instructions and diagrams are supplied with each Floor Bracket
Kit.
8.5 Rear Heat Shield (# 154385)
A stove rear heat shield has been specifically designed for the
J~tul F 400 to reduce clearances off the rear of the stove to
combustible materials. Use of the heat shield alms eat affect the
clearance off the sides of the appliance. See pages 8-9 for specific
clearance requirements. Complete installation instructions are
supplied with the heat shield.
No other type of heat shield may be used on the rear of the
J~tul F 400.
8.6 Bottom Heat Shield (# 54384}
The bottom heat shield supplied with your stove has been
specifically designed for the Jotul F 400. It is required in all
alcove installations. Use of the bottom heat shield does nat
affect tbefloor protection requirements described on page 6 of
this manual.
No other type of heat shield may be used on the bottom of the
J~tul F 400.
USA/Canada
J~tul F 400 Woodstove Clearances
Unprotected Surface
Parallel to the Wall
Protected Surface
Parallel to the Wall
Important:
Connector heatshields and double wall pipe must be a listed product.
Always follow the manufacturer's instructions.
Unprotected Surface
Corner Installation
Protected Surface
Corner Installation
USA/Canada
Jetul F 400 Woodstove Clearances
Stove Unprotected Surface Protected Surface Installation
Clearances Installation PER NFPA211 OR CAN/CSA -B365-M93
Side Rear Come~ Side Rear Come~
Stove -no heatshield 19' A 25" B 18' C 11n D 7" E 8' F
single wall pipe 485mm 635mm 46omm 28omm 18omm 2osram
Stove -with rear heatshield 18~ G 18' H 13~ I irn J 7" K 8' L
single wall pipe 46omm 46omm 33ornm 28omm 18omm 2osram
Stove -no heatshields
double wall pipe 4osmm 485mm 33omm 2osram 18omm 15omm
Stove -with rear heatshield 15~ M 7" N 11~ O 8' P 7" Q 6~ R
with connector shield 38omm 18omm 28omm 2osmm 18omm 15omm
Stove -rear heatshield ~s"S 7"T 11"U 8"V 7"W 6"X
with double wall pipe 38omm 18omm 28omm 2osmm 18omm 15omm
Connector Unprotected Surface Protected Surface
Clearances (Pipe) Vertical Installation Vertical Installation
Single wall pipe 25"
635mm ~oomm
Single wall pipe 18~ 7"
with rear heatshield 46omm 18omm
Single wall pipe
with connector shields 18omm 18omm
Double wall pipe 7" 7"
18omm 18omm
Connector Unprotected Surface Protected Surface
Clearances (Pipe) Horizontal Installation Horizontal Installation
PER NFPA2~I OR CAN/CSA-B365-M93
Singlewall connector 18' 46omm 7" 18omm
Double wall Pipe 6~ 15omm 6" 15omm
Mantel and Trim
Clearances
Stove to 1~ thick or less, side trim 13~ 3oomm
Stove to 1~ thick or less, top trim 23~ 585mm
Stove to mantel- maximum mantel depth 12" 25" 635mm
USA/Canada
Fig. 1
25 3/4'
2C~ 1/2"
top exit 25 1
Imar ex~i~~
1
281/2'
Fig. 2
Fig. 3
Fig. 4
Flue liner
wood stud 2' clearance
from chimney wall
Header
Thimble assembl~. 12" of
brick separation from clay
liner to combustibles~ 12'
Firecla)
minimum or equivalent
Sill / suppo~
Chimney wall
USA/Canada
Fig. 5
Fig. 6
Fig. 7
Connector pipe shall
be flush with the inside
of the flue tile
Connector extends
to first flue tile
Damper opening is
sealed with sheet metal
sealant
Usted chimney )~ ~
Attic insulation. ~ ~ ~ ~ ~ChJmn~
U II
Fig. 8
Fig. 9
Fig. *~o
Hearth Protection
Unprotected alcove installation
(with double-wall pipe)
~6' (4o5mm)
~6' (4osmm)
(~68 mm)
Protected alcove installation
(with double-wall pipe)
8' (2osmm)
r (~o5mm)
Max. depth 48'
(1=~o mm)
Min. Depth 44"
(n68 mm)
(~47smm)
(~o65mm)
Protection and
air space must
comply with
NFPA 211OR
CAN/CSA-B]65.
USA/Canada
Fig. il
Far le~ Far right
Full close~ Full open
Fig. 12
Stove top
thermometer
Fig. 13
Glass
Del liste / Part list F 400 SD
J~tul
A5
Tegning nr: 4-3770-PO6 DMaatre05
Fredrikstad,Norway
USA/Canada
Part list for the J~tul F 400 woodstove
Consult your dealer for part numbers and replacement parts.
No. Description
Ashlip Packed
2 Handle Ash Door Compl.
Latch
4 ~pring for Latch
5 Nut Hex.
6 Screw
7 Gasket L~1o2o
29 ~
Appendix A
Alternate floor protection
All floor protection materials must be non-combustible ie. metal,
brick, stone, mineral fiber boards). Any combustible material
may not be used.
The easiest means of determining if a proposed alternate floor
material meets requirements listed in this manual is to follow
this procedure.
R-value = thermal resistance
k-value -- thermal conductivity
C-value = thermal conductance
1. Convert the specification to R-value;
a. If R-value is given, no conversion is needed.
If k-value is given wRh a required thickness (T) in inches:
R--1/k X T.
c. If C-value is given: R=r/C.
2. Determinethe R-valueofthe pmpased alternate float pmtectoc
a. UsetheformulainStepltoconvert valuesnotexp~essed
as "R~.
b. For multiple layers, add R-values of each laye~ to determine
overall R-value.
3. Ifthe overall R-value ofthe sustem is greater than the R-value
of the specified floor protector, the alternate is acceptable.
The specified floor protector should be 3/4"thick material with a
k-factor ofo.84- The pmpased alternate is 4" brick with a C-factor
of 1.25 over 118' mineral board with a k-factor of 0.29.
Step A. Use formula above to convert specifications to R-value.
R=r/k X T= 11.84 X .75 = .893
Step B. Calculate R of proposed system.
4" brick of C-1.25, therefore
R brick ~ 1/C = 1/1.25 = o.8o.
1/8" mineral board of k -- o.29 therefore
R mineral board = r/.29 X o.r25 = o.431
Total R = R brick + R mineral board=
o.8 + o.431=1.23~
StepC Compare proposed system R = 1.231to specified R of o.893.
Since R is greater than required,the system is acceptable.
IX..t~inltions:
Thermal conductance =
C= Btu -- W
(hr)(ft~)(F) (m~)(K)
Thermal conductivity =
k= Btu = W = (Btu)
(hr)(fl?)(F) (rrP)(K)
Thermal resistance=
R~ Btu ~_rr~)(K) ~ {Btu){inch)
(hr)(ft])(F) W (hr)(ft~)(F)
Sluttkontroll av ildsteder Quality control of stoves and fireplaces
Checked
Utfert Kontrollpunkt Controlled item
v~ Alle deler er med i produktet (ifelge stmktur). All parts are included.
~, Alle festemidter er av korrekt type, og er korrekt Correct fastener Rems have been used and
anvencit, correctly applied.
Ovenqater er i samsvar reed Jetuls Surfaces comply with Jetul workmanship
kvalitetsstandarder, standards.
v~ Lukkemekanismer fungerer som de skal, o8 uten Door locking mechanisms function correctly;
behov for unedig stor kraft, excessive force is not needed.
The product/lot complies with the leakage test
v~ Produktet/serien meter kravet for lekkasjetest.
requirement-
/ Lakkerte/emaljerte overflater meter kravene i Paint/enamel surface finish complies with J~tul
Jetuls kvalitetsstandarder. ! workmanship standards.
Surfaces are not contaminated by external stove
~' Produktet er frRt for utvendig kit't- eller limklin.
cement or glue.
/ Produktet hat ingen sprekker i glass, stepejem There are no cracks in glass, cast iron or other parts.
eller andre deler.
Pakninger er riktig lagt, og skjemmer ikke Gaskets are correctly applied and do not degrade
~' produktet ved stygge ender eller ved at product appearance (i.e. loose ends or excessive
pakningen er un~adig synlig. ' visible exposure).
~/' Derpakninger er godt limt. Door gaskets are firmly glued/fixed to the door.
/ D~rpakninger hat tilfredsstillende pakningstrykk. Door gaskets provide satisfactory sealing.
v/ Sjekk at det ikke Nlyser gjennom" i derpakning Check for "light through" at door seals and other
eller andre sammenfeyninger, relevant locations.
· /' Trekkhendler osv fungerer normalt. The function of air valve handle etc is normal.
Jetul bekrefter herved at dette produktet er kontrollert og
funnet -~ v~ere i samsvar med v-~re kvalRetsnormer.
Lot#/Serie nr.
Jetul hereby confirm that this product has been QC
inspected and found to comply with our quality
standards.
Checked by/kontrollert av J DatelDato:
Dokument hr. KI5-580 02 03
J TU£
J~atul pursue a policy of constant product development. Products supplied may therefore
differ in specification, colour and type of accessories from those illustrated and described in
the manual.
Quality
J~tul AS has a quality system that conforms to NS-EN ISO 9ool for product development,
manufacturing, and distribution of stoves and fireplaces. This policy gives our customers
quality and safety piece of mind as a result of J~tul's vast experience dating back to when
the company first started in 1853.
Jetul North America Inc.
55 Hutcherson Drive
Gotham, Maine 04038
USA
Jetul AS
P.o. box 1411
N-1602 Fredrikstad,
Norway