HomeMy WebLinkAbout51031-Z TOWN OF SOUTHOLD
BUILDING DEPARTMENT
46 F TOWN CLERK'S OFFICE
s �Af SOUTHOLD, NY
BUILDING PERMIT
(THIS PERMIT MUST BE KEPT ON THE PREMISES
WITH ONE SET OF APPROVED PLANS AND SPECIFICATIONS
UNTIL FULL COMPLETION OF THE WORK AUTHORIZED)
Permit#: 61031 Date: 8/2/2024
Permission is hereby granted to:
Stratigos, Theodore
30 W St Apt 12B
New York, NY 10004
To: legalize "as built" hot tub as applied for per Trustees. Additional certification may be
required.
At premises located at:
550 Blue Marlin Dr., Green port
SCTM # 473889
Sec/Block/Lot# 57.-1-27
Pursuant to application dated 6/29/2020 and approved by the Building Inspector..
To expire on 2/1/2026.
Fees:
AS BUILT- SWIMMING POOL $600.00
CO- SWIMMING POOL $100.00
Total: $700.00
Building nspector
TOWN OF SOUTHOLD—BUILDING DEPARTMENT
Town Hall Annex 54375 Main Road P. O. Box 1179 Southold,NY 11971-0959
r: Telephone (631) 765-1802 Fax (631) 765-9502 ht! :Hwww.soutli,oldtownn .gov
Date Received
APPLICATIONNT
For Office Use Only D LES ff[E
PERMIT NO. '16 Building Inspectnc, /i/ .:'
A U G _ qp 2024 �
Applications and forms must be filled out in their entirety.Incomplete
applications will not be accepted. Where the Applicant is not the owner,an IBUELDING
Owner's Authorization form(Page 2)shall be completed. TOWN S DEPT.
Date: I"' ;�j fuir 2:?.4,
OWNER(S)OF PROPERTY:
Name: ?'uwboap- � ctlt —9-9A'tiCAS SCTM# 1000-057.00 — 01.00 027.00
Project Address: SS-0 l we t-ucu'&J b6VE ovTweLm, M� 11171
Phone#: 91`1. 608 . 816E Email: [,st,.t; S @ �roa� �.com
Mailing Address: SSO &A t-*L'i j
CONTACT PERSON: �Ji p ( '' 11
Name: �,SEL r Dfic 9-L-i aaH9>�
Mailing Address: P.a , 8,sc 1"1 S$ �-Uf Lb'
Phone#: Email, n; 2(_ c�,It k;tecL .t*ncz Uom
. 5��4. q 74�- @
DESIGN PROFESSIONAL INFORMATION:
Name:
Mailing Address:
Phone#: Email:
CONTRACTOR INFORMATION:
Name:
Mailing Address:
Phone#: Email.
DESCRIPTION OF PROPOSED CONSTRUCTION
[]New Structure ❑Addition ❑Alteration ❑Repair ❑Demolition Estimated Cost of Project:
Mother A.s- Lt-r U� J 0,,-i6QbtAE0TS 9,M OC 14A 'emir
Will the lot be re-graded? ❑Yes ❑N_q Will excess fill be removed from premises? WYes ONO
1
PROPERTY INFORMATION
a Existing use of property: S14CLe FA#4I I..4 DwEwiA)q Intended use of property:5i,Jgt.E FpMILU 9bWCL.L.iN4-
Zone or use district in which premises is situated: Are there any covenants and restrictions with respect to
P,4.0 this property? ❑Yes 9No IF YES, PROVIDE A COPY.
DO Check Box After Reading: The'owner/contractor/design professional is responsible for all drainage and storm water issues as provided by
Chapter 236 of the Town Code. APPLICATION IS HEREBY MADE to the Building Department for the issuance of a Building Permit pursuant to the Building Zone
Ordinance of the Town of Southold,Suffolk,County,New York and other applicable Laws,ordinances or Regulations,for the construction of buildings,
additions,alterations or for removal or demolition as herein described.The applicant agrees to comply with all applicable laws,ordinances,building code,
housing code and regulations and to admit authorized inspectors on premises and in building(s)for necessary inspections.False statements made herein are
punishable as a Class A misdemeanor pursuant to Section 22GA5 of the New York State Penal Law.
Application Submitted By(print name): 11 I&F-L Q08E2T W j Lt.i a MSOJ MAuthorized Agent ❑Owner
Signature of Applica " "== � � Date: 149�;Vf r' � •
STATE OF NEW YORK)
SS:
CO U NTY O F )
4411 1rf Q;Li.IAmsQj being duly sworn, deposes and says that(/)he is the applicant
(Name of individual signing contract) above named,
Y'Ahe is the ACrEkI f
(Contractor,Agent, Corporate Officer,etc.)
of said owner or owners, and is duly authorized to perform or have performed the said work and to make and file this
application;that all statements contained in this application are true to the best of his/her knowledge and belief; and
that the work will be performed in the manner set forth in the application file therewith.
Sworn before me this
1 day of AvNj-T- . 20 2-4.
N otpoty ..
JANNUZZ1
NOTARY PI»SUC,STATE OF NEWYORK
Registration No.02JA6052 85
Qualified in Suffolk County
PROPERTY OWNER AUTHORIZATION Commission Expires February 13,� ~
(Where the applicant is not the owner) "
I Q residing at aqjf, tj&gLIAi ZIdVG
�uTltoul7 ld- 11471 do hereby authorize tj 6 ALL•Af�i.) to apply on
my behalf to the Town of Southold Building Department for approval as described herein.
ic
Z: 202-4. —
Owner's Signature Date
T'N EO'Dagf-, fifipg
Print Owner's Name
2
BUILDING DEPARTMENT- Electrical Inspector
TOWN OF SOUTHOLD
w,
Town Hall Annex - 54375 Main Road - PO Box 1179
Southold, New York 11971-0959
Telephone (631) 765-1802 - FAX (631) 765-9502
arnesh outholdtownn . ov seand southoldtownn ov
,
APPLICATION FOR ELECTRICAL INSPECTION
ELECTRICIAN INFORMATION (All Information Required) Date:
Company Name:.
Electrician's Name:
License No.: Elec. email:
Elec. Phone No: ❑I request an email copy of Certificate of Compliance
Elec. Address.:
JOB SITE INFORMATION (All Information Required)
Name: ejoBoQE eJX<.4 Slyf; S
Address: a ikj _(� vT-pwLb N.4. ll 71
Cross Street: Cb H,v h6 v€
Phone No.: 631. 83 . -7 0
Bldg.Permit #: email: n e1 _zil, �o -LID
Tax Map District: 1000 Section: 051.ao Block: bi. ono Lot: 0z,7_oo
DESC TION OF WQRK, INCLUDE SQUARE FOOTAGE (Please Print Clearly):
P4 r 7v a
Square Footage:
Circle All That Apply:
Is job ready for inspection?: YES ONO [—]Rough In Final
Do you need a Temp Certificate?: El YES 0 NO Issued On
Temp Information: (All information required)
Service Size Ell Ph[:]3 Ph Size: A # Meters Old Meter#
❑New Service❑Fire Reconnect[:] round Flood Reconnect❑Service Reconnect❑Underg ❑Overhead
# Under
ground Laterals 1 2 H Frame Pole Work done on Service? Y N
Tr�c
n.
A U U - 1 2024
PAYMENT DUE WITH APPLICATIC?I�I'
RLM,DING DF-PT.
TI-YVV . ,-F S0 TI-IOI
Glenn Goldsmith,President soy Town Hall Annex
54375 Route 25
Michael J.Domino P.O.Box 1179
AL
John M.Bredemeyer III ' Southold,New York 11971
A.Nicholas Krupski Telephone(631) 765-1892
Greg Williams Fax(631)765-6641
BOARD OF TOWN TRUSTEES
TOWN OF SOUTHOLD
Permit No.: 9735A
Date of Receipt of Application: October 7, 2020
Applicant: Jacqueline Pottgen
SCTM#: 1000-57-1-27
Project Location: 650 Blue Marlin Drive, Southold
Date of Resolution/Issuance: October 28, 2020
-Date of Expiration: October 28, 2022
Reviewed by: John M. Bredemeyer, III, Trustee
Project Description: For the as-built 1,100sq.ft. deck with 37 x7' stairs with a 60sq.ft.
hot tub; and as-built metal 218sq.ft.awning.
Findings: The protect meets all the requirements fir issuance of an Administrative
Permit set forth in Chapter 275 of the Southold Town Code. The issuance of an
Administrative Permit allows for the operations as indicated on the'survey prepared by
Gary Benz, L.S., dated January 24, 2020 and stamped approved on October 28, 2020.
Special Conditions: None
Inspections: Final Inspection.
If tie proposed activities do not meet the requirements for issuance of an Administrative
Permit set forth in Chapter 275 of the Southold Town Code, a Wetland Permit will be
required.
This is not a determination from any other agency.
Glenn Goldsmith, President
Board of Trustees
Glenn Goldsmith,President q o Town Hall Annex
A.Nicholas Krupski,Vice President 54375 Route 25
P.O.Box 1179
Eric Sepenoski Southold,New York 11971
Liz Gillooly Alc Telephone(631) 765-1892
Elizabeth Peeples Fax(631) 765-6641
BOARD OF TOWN TRUSTEES
TOWN OF SOUTHOLD
CERTIFICATE OF COMPLIANCE
2059C Date: ,Au ;�tst�2
THIS CERTIFIES that the existin&I 100saft deck vrfth -°7"x7' stairs with a 60sq,, hot kub�an,�l�m:
built metal 218so.ft.aw"nin ;
At 550 Blue Marlin Drive.Sonthld
Suffolk County Tax Map 1000-57-.1-27
Conforms to the application for a Trustees Permit heretofore filed in this
office Dated October 7,2020 pursuant to which Trustees Administrative Permit#9735A
Dated October 2,8,2020.was issued and conforms to all
the requirements and conditions of the applicable provisions of law. The project for which
this certificate is being issued is for existing 1�LQ0s%, t,deck.with 37xT...sta.irs with,a 60s -& loot tmbl
and as-built metal 218saftawnine.
The certificate is issued to jacquelioe Pottgen owner of the
aforesa property,
Authorized Signature
AP "ED A3 NOTED
IAA B.P.# ��j
FEE � " BY: r
NOTIFY BUILDING DEPARTMENT AT
631-765-1802 8AM TO 4PM FOR THE
FOLLOWING INSPECTIONS:
I. FOUNDATION-TWO RE01+"n,pn
FOR POURED CONCRII:-".
2. ROUGH-FRAMING& PL_ ,
3. INSULATION REQUIRED
4. FINAL-CONSTRUCTION MUST INSPECDON
BE COMPLETE FOR C.O.
ALL CONSTRUCTION SHALL MEET THE
REQUIREMENTS OF THE CODES OF NEW
YORK STATE. NOT RESPONSIBLE FOR
DESIGN OR CONSTRUCTON ERRORS
COMPLY WTH ALL CODES OF
NEW K STATE & TOWN CODES
AS SQUIRED AND CONDITIONS OF
!- i
Certification
O�D TOWN TRUSTEES May Be Required.
OCCUPANCY OR
USE IS UNLAWFUL
WITHOUT I I -'
OF OCCUPANCY
=m
r
Y � I
o i
I�
I�I���' �� '�'�'iloi� i� ullllllllll�lllllllllll I I�
„ �� VVVV VV VVVVV
uuuu�igiuuVPVuG�uUuuip����uuupU�pU��iiU�uuuui�iiiiuiiiiii�uiuuuuuuuuuuuuYuiiiiii�iuYuuYuiiiuYuiiiiuui
f
I
1
n
i
s"tis
i rq
f f Irdjl �I
I
jir � 1
✓ /, (� p � sl r i i � i I 1 1�
/
r �
rr/
I l I f
,
��l f4 Mtf-0dtr Nf NI dNi IYit!fa! �f 6rill� �� � �i t1�5iMV�tP � � � ��
IMPO R llfAlll`°,,Ill T' ,,"3�,///l���lll °llf,,,,,. 111'Y llllll'°°���a1S 'I'll 1111,'Ill,,,,llV!;7lllONS
READ AND FOLLOW ALL INSTRUCTIONS
AVOIDING THE RISK TO CHILDREN
ADAN :
• RISK OF CHILD DROWNING.Extreme caution must be exercised to prevent unauthorized access by children.To avoid accidents,ensure that children cannot
use a spa unless they are supervised at all times.
OWARNING:
• To reduce the risk of injury,do not permit children to use this spa unless they are closely supervised at all times.
• To reduce the risk of injury,lower water temperatures are recommended for young children.Children are especially sensitive to hot water.
DO
• Make sure you always lock the child resistant locks after using the spa for your children's safety.Every Caldera,9 spa is equipped with a locking cover that meets
the ASTM F1346-91 Standard for Safety Covers.
• Test the water temperature with your hand before allowing children to enter the spa to be sure that it's comfortable.Children are especially sensitive to hot water.
• Remind children that wet surfaces can be very slippery.Make sure that children are careful when entering,or exiting the spa.
DON'T
• Allow children to climb onto the spa cover.
• Allow children to have unsupervised access to the spa.
AVOIDING THE RISK OF ELECTROCUTION
Risk of electrocution
• Connect only to a grounded source.
• Do not bury the power cord.A buried power cord may result in death,or serious personal injury due to electrocution if direct burial-type cable is not used,or if
improper digging occurs.
• A ground terminal(pressure wire connector)is provided on the control box inside the unit to permit connection of a minimum No.10 AWG solid copper bonding
conductor between this point and any metal equipment,metal water pipe,metal enclosures of electrical equipment,or conduit within five feet(1.5 m)of the unit
as needed to comply with local requirements.
0 WARNING:
• To reduce the risk of electrical shock,replace a damaged cord immediately.Failure to do so may result in death or serious personal injury due to electrocution.
• Your spa is provided with a Ground Fault Circuit Interrupter for user and equipment protection.To ensure proper operation of this important safety device,test
according to the following instructions per electrical configuration.
�0 volt,per a rrtl I sf lled rrws�dets
• A ground terminal is provided on the terminal block located inside the control box.To reduce the risk of electric shock,connect this terminal to the grounding
terminal of your electrical service or supply panel with a continuous green,insulated copper wire.The wire must be equivalent in size to the circuit conductors
supplying the equipment.In addition,a bonding terminal(pressure wire connector)is provided on the outside of the control box for bonding to local ground
points.To reduce the risk of electric shock,this connector should be bonded with a No.10 AWG solid copper wire to any metal ladders,water pipes,or other
metal within 5 feet(1.5 m)of the spa to comply with local requirements.The means of disconnection must be readily accessible,but must be installed at least 5
feet(1.5 m)from the spa.
• Your spa is provided with a suitably rated circuit breaker to open all ungrounded supply conductors.
• Your spa uses ground fault circuit interrupters in the electrical subpanel.Before each use of the spa and with the unit operating,push the TEST button on each
breaker.The switch should click over to the"Trip"position.Wait 30 seconds and reset each GFCI breaker by switching it completely off and then completely on.
The switch should then stay on.If either of the interrupters does not perform in this manner,it is an indication of an electrical malfunction and the possibility of
an electric shock.Disconnect the power until the fault has been identified and corrected.
ODANGER:RISK OF ELECTRICAL SHOCK
• Install spa at least 5 feet(1.5 m)from all metal surfaces.A spa may be installed within 5 feet of a metal surface if each metal surface is permanently connected
by a minimum No.10 AWG solid copper conductor attached to the wire ground connector on the terminal box that is provided for this purpose if in accordance
with National Electrical Code ANSVNMFPA70-1993.
• Do not permit any electrical appliances,such as a light,telephone,radio,or television within 5 feet(1.5 m)of a spa.Failure to maintain a safe distance may
result in death,or serious personal injury due to electrocution,if the appliance should fall into the spa,
• Install your spa in such a way that drainage is away from the electrical compartment and from all electrical components.
REQ �I�I,I��� � �,�� it ����NI" 111
Your Caldera Spa has been carefully designed to give you maximum safety against electrical shock.Connecting the spa to an improperly wired circuit will negate many
of the spa's safety features.Improper wiring may also cause electrocution,risk of fire,and other risks of injuries.Please read and follow the electrical installation
requirements and instructions for your spa completely!
SERVICE NOTE:All Caldera spas have diagnostic functions that are displayed on the control panel.Four flashing lines are visible on the control panel if the heater high
limit thermostat has tripped.If the four flashing lines are visible,follow the instructions in the troubleshooting section to identify and correct the cause.The four flashing
lines will stop flashing once the problem has been corrected.
I'll Ill �l'° 111 fNlll "Ill ° ' 1 1° Il' ° IINll°��lv,� 111 ,NTl1i� � � � , 11
CALDERA SPAS MUST BE WIRED IN ACCORDANCE WITH ALL APPLICABLE LOCAL ELECTRICAL CODES.ALL ELECTRICAL WORK SHOULD BE DONE BY AN
EXPERIENCED LICENSED ELECTRICIAN.WE RECOMMEND THE USE OF APPROPRIATE ELECTRICAL CONDUIT,FITTINGS,AND WIRE FOR ALL CIRCUITS.
An electrical subpanel containing two GFCI breakers is included with each spa.We recommend that this subpanel be used to supply power and protect the spa.
This subpanel requires a 50 amp,single phase,230 volt,four wire service(two line,one neutral,one ground).The ground wire must never be less than#10 AWG.Use
NEC 250-122(table)and local codes for more information.A minimum#10 AWG solid copper bond wire is also required.
Mount the subpanel in the vicinity of the spa,but not within five feet,in accordance with local codes.
INSTALLATION INSTRUCTIONS
1. To connect the electrical service,first remove the screws from the equipment compartment door,lower the door one inch and remove the door.
2. Locate the spa control box.Remove the screws on the front of the control box and remove the control box cover.
3. Route the electrical service from the subpanel into the spa equipment compartment.
NOTE:The subpanel must be placed in sight of the spa,no closer than five feet.
4. Connect wire to bottom of control box using a minimum of 1/4'liquid-tight,flex conduit fitting.
WIRING CONNECTIONS
1. Identify the TB-1 terminal block,located inside the control box at the lower left-hand corner.
2. Connect the#12 AWG,BLUE wire,from the subpanel 20 amp breaker,terminal L1 to TB-1,terminal 1
3. Connect the#12 AWG,RED wire,from the subpanel 20 amp breaker,terminal L2 to TB-1,terminal 3
NOTE:The WHITE neutral wire must be attached to the LOAD neutral on the 230 volt,30 amp breaker(not to the neutral bus bar in the subpaneo,The WHITE neutral
wire coming from the breaker itself is already connected to the neutral bus bar.
4. Connect the#10 AWG,BLUE wire,from the subpanel 30 amp breaker,terminal L1 to TB-1,terminal 2
5. Connect the#10 AWG,RED wire,from the subpanel 30 amp breaker,terminal L2 to TB-1,terminal 4
6. Connect the#10 AWG,WHITE wire,from the subpanel 30 amp breaker,terminal N(load neutral)to TB-1,terminal 5
7. Connect the#10 AWG,GREEN wire,from the subpanel GROUND bar to TB-1,system ground terminal.
6. Using the pressure wire connector provided on the outside of the control box,bond the spa to all exposed metal equipment or fixtures,handrails,and the concrete
pad(if applicable)per N.E.C.and local codes.
9. Replace the control box cover and securely tighten the fastening screws.Close and secure the equipment compartment door as follows:
•Place top of door or panel directly below bartop against the frame of the spa.
e Push bottom of door or panel against the spa frame.
Slide door or panel upward(pushing in on center of door)until screw holes line up.
e Slightly pull on door or panel,if door remains against the spa then replace the screws.
•If the door does not lock into position,repeat the previous steps.
0 WARNING:FILL THE SPA WITH WATER BEFORE TURNING ON THE POWER!(See STARTUP AND REFILL PROCEDURES).
Once your spa has been filled with water,turn it on and test all of the circuit breakers.
NOTE:If both breakers immediately trip,verify that the#10 AWG WHITE neutral wire is connected from TB-1 terminal 5 to the N(load neutral)terminal of the 30 amp
subpanel breaker.Each breaker should be tested prior to each use.Here's how:
1. Push the"TEST"button on each GFCI breaker,and observe it click OFF.
2, Wait 30 seconds,then push the breaker switch to the OFF(down)position(to ensure that it has completely disengaged),then push the breaker switch to the ON
(up)position.If you don't wait 30 seconds,the spa's control panel may flash four lines on and off—try again.
If any of the GFCI breakers fails to operate in this manner,your spa may have an electrical malfunction,and you may be at risk of electrical shock.Turn off all circuits
and do not use the spa until the problem has been corrected by an authorized service agent.
SERVICE NOTE:All Caldera spas have diagnostic functions that are displayed on the control panel.Four flashing lines are visible on the control panel if the heater high
limit thermostat has tripped.If the four flashing lines are visible,follow the instructions in the troubleshooting section(See pg.37 to identify and correct the cause.The
four flashing lines will stop flashing once the problem has been corrected.
As WARNING:Removing or bypassing any GFCI breaker will result in an unsafe spa and will void the spa's warranty.
IMPORTANT:Should you ever find the need to move or relocate your Caldere spa,it is essential that you understand and apply these installation requirements.Your
Caldera spa has been carefully engineered to provide maximum safety against electric shock.Remember,connecting the spa to an improperly wired circuit will negate
many of its safety features.
NOTE:Long wiring runs may require larger-gauge wire than stated.
230 Volt Permanently Connected
WARNING!
THE EXACT PHYSICAL LOCATION OF THE TERMINALS ON THE GFCI BREAKER
WILL VARY BETWEEN MANUFACTURERS, CONNECTING THE HOT WIRE TO THE
NEUTRAL TERMINAL WILL CAUSE IRREVERSIBLE DAMAGE TO THE CONTROL BOX. HEATER
GROUND
230V, 50 Amp, TB1
2—POLE,
CIRCUIT BREAKER
(NON GFCI) ell I0
LS
IS AWG WHITE,NICUTRA4
110 AWO o .4F1(x1NV0"" L� �
LZ Try A � �
re A*0 BLUE L1 Ta 20A Ll #12 A40 BLUE
50A fS A*G RED.L2 tl, q1'0 A TIED
30A LI #10 A*G BLUE
tr $10 AWO 1TE C
0
MAIN SERVICE
ELECTRICAL
PANEL " GRD
*SUBPANEL Nil FEET System Ground Terminal
WITH GFCI �e ST�A mmbe
Hof dw spa
Domot exceed 50 FEET.
LESS THAN 100 FT, BREAKERSCONTROL BOX
Refer to NEC 250-122(table)
NOTE:The wire connections to GFCI breakers are for reference only.,Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker
*PROVIDED WITH SPA. NOTE: ALL WIRING SHOULD BE COPPER.
POWER R CONNECTION ACCESS
CONTROL BOX
DOOR
SOINRINC'ACCESS 0 DRAIN
OPENINGS ON RIGHT&LEFT
HAND SIDE
THE AREA OF THIS PROPERTY IS 23,620 S.F OR 0.542 ACRES
CLEARING CALCULATIONS
EXISTING CLEARING IS 23,620 S.F. (100%)
COVERAGE CALCULATIONS
ALLOWABLE COVERAGE IS 4,724 S.F. (20%)
EXISTING COVERAGE IS 3,798 S.F. (16.17Cb
� 1
MG �
OF
r �
N cn
O
O_ '
`1m N 89'15'00" E i�p N 1 5
269.55
�
i MON� R
o
^ry.
N
N
Z
pRIVE
Z R%C A
G
6
1 � J
R 6 AAa
1
OM
CD
i a,W
t 0.13
A VORt
cn �oTCD
,
N
00 LOT 6
LOT 5
,-FRAME ButXNEAp�5„.w
n za 1 E
WATER jallo 13;U S 85SSFi6� W
CONIC
CERTIFIED T0: � (� 1�ND AND) t
Jacqueline Pottgen c��
GUARANTEES INDICATED SHALL RUN ONLY TO THE PERSON FOR WHOM THE SURVEY IS PREPARED AND/OR AGENCY, AND ARE NOT TRANSFERABLEE,
S.C.T.M. N 0. 1000 — 57 — 1 — 27
SURVEY OF: LOT 6
MAP OF SOUTHOLD SHORES GARY BENZ, L.S.
FILED AUG. 29, 1963 — AS No. 3853 Surveying and Land Planning
SITUATED IN: SOUTHOLD (ARSHAMOMAQUE) TOWN OF: SOUTHOLD 527-B Hawkins Avenue
SUFFOLK COUNTY, NEW YORK Ronkonkoma, N.Y. 11779
DATE: 1/24/2020 JOB NO. G20-5435 SCALE: 1" = 30 GaryBenzLS®Yahoo.com / (631) 648-9348
THE EXISTENCE OF RIGHT OF WAYS, WETLANDS, UNDER UNAUTHORIZED ALTERATION OR ADDITION TO COPIES OF THIS SURVEY MAP NOT BEARING THE LAND
GROUND UTILITIES AND/OR EASEMENTS OF RECORD THIS SURVEY IS A VIOLATION OF SECTION 7209 SURVEYOR'S INKED SEAL OR EMBOSSED SEAL SHALL
IF ANY, NOT SHOWN ARE NOT GUARANTEED. OF THE NEW YORK STATE EDUCATION LAW. NOT BE CONSIDERED TO BE A VALID TRUE COPY.
J/4 '
Owner's. anus
_ ' � Ate- l;�, .«.: t r., ---�---�• -
777
', :.. '•:�`, .-.sue' .;✓ .,��- Y+b�,r ,.`:;fi.•,' :a�'«� '+'y1; x�41 •__ l
:• .. �_ � •�} ��� n,o� z �:ice. . � ,�� ' � ���• �,_�� : ��'. �'`���� .� ��_ . � ���.. e• , • �. -
t�;5:1�''L '�t'y�7 �z,`+ .s..- a's•:s.
IMPORTANT SAFErVr INS TRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
AVOIDING THE RISK TO CHILDREN
ADANGER:
• RISK OF CHILD DROWNING.Extreme caution must be exercised to prevent unauthorized access by children.To avoid accidents,ensure that children cannot
use a spa unless they are supervised at all times.
A WARNING:
• To reduce the risk of injury,do not permit children to use this spa unless they are closely supervised at all times.
• To reduce the risk of injury,lower water temperatures are recommended for young children.Children are especially sensitive to hot water.
DO:
• Make sure you always lock the child resistant locks after using the spa for your children's safety.Every Caldera,9 spa is equipped with a locking cover that meets
the ASTM F1346-91 Standard for Safety Covers.
• Test the water temperature with your hand before allowing children to enter the spa to be sure that it's comfortable.Children are especially sensitive to hot water.
• Remind children that wet surfaces can be very slippery.Make sure that children are careful when entering,or exiting the spa.
DON'T:
• Allow children to climb onto the spa cover.
• Allow children to have unsupervised access to the spa.
AVOIDING THE RISK OF ELECTROCUTION
Risk of electrocution
• Connect only to a grounded source.
• Do not bury the power cord.A buried power cord may result in death,or serious personal injury due to electrocution if direct burial-type cable is not used,or if
improper digging occurs.
• A ground terminal(pressure wire connector)is provided on the control box inside the unit to permit connection of a minimum No.10 AWG solid copper bonding
conductor between this point and any metal equipment,metal water pipe,metal enclosures of electrical equipment,or conduit within five feet(1.5 m)of the unit
as needed to comply with local requirements.
A WARNING:
• To reduce the risk of electrical shock,replace a damaged cord immediately.Failure to do so may result in death or serious personal injury due to electrocution.
• Your spa is provided with a Ground Fault Circuit Interrupter for user and equipment protection.To ensure proper operation of this important safety device,test
according to the following instructions per electrical configuration.
230 volt,permanently installed models:
• A ground terminal is provided on the terminal block located inside the control box.To reduce the risk of electric shock,connect this terminal to the grounding
terminal of your electrical service or supply panel with a continuous green,insulated copper wire.The wire must be equivalent in size to the circuit conductors
supplying the equipment.In addition,a bonding terminal(pressure wire connector)is provided on the outside of the control box for bonding to local ground
points.To reduce the risk of electric shock,this connector should be bonded with a No.10 AWG solid copper wire to any metal ladders,water pipes,or other
metal within 5 feet(1.5 m)of the spa to comply with local requirements.The means of disconnection must be readily accessible,but must be installed at least 5
feet(1.5 m)from the spa.
• Your spa is provided with a suitably rated circuit breaker to open all ungrounded supply conductors.
• Your spa uses ground fault circuit interrupters in the electrical subpanel.Before each use of the spa and with the unit operating,push the TEST button on each
breaker.The switch should click over to the"Trip"position.Wait 30 seconds and reset each GFCI breaker by switching it completely off and then completely on.
The switch should then stay on.If either of the interrupters does not perform in this manner,it is an indication of an electrical malfunction and the possibility of
an electric shock.Disconnect the power until the fault has been identified and corrected.
ADANGER:RISK OF ELECTRICAL SMOCK
• Install spa at least 5 feet(1.5 m)from all metal surfaces.A spa may be installed within 5 feet of a metal surface if each metal surface is permanently connected
by a minimum No.10 AWG solid copper conductor attached to the wire ground connector on the terminal box that is provided for this purpose if in accordance
with National Electrical Code ANSVNMFPA70-1993.
• Do not permit any electrical appliances,such as a light,telephone,radio,or television within 5 feet(1.5 m)of a spa.Failure to maintain a safe distance may
result in death,or serious personal injury due to electrocution,if the appliance should fall into the spa.
• Install your spa in such a way that drainage is away from the electrical compartment and from all electrical components.
Your Caldera'Spa has been carefully designed to give you maximum safety against electrical shock,Connecting the spa to an improperly wired circuit will negate many
of the spa's safety features.Improper wiring may also cause electrocution,risk of fire,and other risks of injuries.Please read and follow the electrical installation
requirements and instructions for your spa completely!
SERVICE NOTE:All Caldera spas have diagnostic functions that are displayed on the control panel.Four flashing lines are visible on the control panel if the heater high
limit thermostat has tripped.If the four flashing lines are visible,follow the instructions in the troubleshooting section to identify and correct the cause.The four flashing
lines will stop flashing once the problem has been corrected.
CALDERA SPAS MUST BE WIRED IN ACCORDANCE WITH ALL APPLICABLE LOCAL ELECTRICAL CODES.ALL ELECTRICAL WORK SHOULD BE DONE BY AN
EXPERIENCED LICENSED ELECTRICIAN.WE RECOMMEND THE USE OF APPROPRIATE ELECTRICAL CONDUIT,FITTINGS,AND WIRE FOR ALL CIRCUITS.
An electrical subpanel containing two GFCI breakers is included with each spa.We recommend that this subpanel be used to supply power and protect the spa.
This subpanel requires a 50 amp,single phase,230 volt,four wire service(two line,one neutral,one ground).The ground wire must never be less than#10 AWG.Use
NEC 250-122(table)and local codes for more information.A minimum#10 AWG solid copper bond wire is also required.
Mount the subpanel in the vicinity of the spa,but not within five feet,in accordance with local codes.
INSTALLATION INSTRUCTIONS
1. To connect the electrical service,first remove the screws from the equipment compartment door,lower the door one inch and remove the door.
2. Locate the spa control box.Remove the screws on the front of the control box and remove the control box cover.
3. Route the electrical service from the subpanel into the spa equipment compartment.
NOTE:The subpanel must be placed in sight of the spa,no closer than five feet.
4. Connect wire to bottom of control box using a minimum of liquid-tight,flex conduit fitting.
WIRING CONNECTIONS
1. Identify the TB-1 terminal block,located inside the control box at the lower left-hand comer.
2. Connect the#12 AWG,BLUE wire,from the subpanel 20 amp breaker,terminal Li to TB-1,terminal 1
3. Connect the#12 AWG,RED wire,from the subpanel 20 amp breaker,terminal L2 to TB-1,terminal 3
NOTE:The WHITE neutral wire must be attached to the LOAD neutral on the 230 volt,30 amp breaker(not to the neutral bus bar in the subpanel).The WHITE neutral
wire coming from the breaker itself is already connected to the neutral bus bar.
4. Connect the#10 AWG,BLUE wire,from the subpanel 30 amp breaker,terminal L1 to TB-1,terminal 2
5. Connect the#10 AWG,RED wire,from the subpanel 30 amp breaker,terminal L2 to TB-1,terminal 4
6. Connect the#10 AWG,WHITE wire,from the subpanel 30 amp breaker,terminal N(load neutral)to TB-1,terminal 5
7. Connect the#10 AWG,GREEN wire,from the subpanel GROUND bar to TB-1,system ground terminal.
8. Using the pressure wire connector provided on the outside of the control box,bond the spa to all exposed metal equipment or fixtures,handrails,and the concrete
pad(if applicable)per N.E.C.and local codes.
9. Replace the control box cover and securely tighten the fastening screws.Close and secure the equipment compartment door as follows:
Place top of door or panel directly below bartop against the frame of the spa.
a Push bottom of door or panel against the spa frame.
•Slide door or panel upward(pushing in on center of door)until screw holes line up,
•Slightly pull on door or panel,if door remains against the spa then replace the screws.
•If the door does not lock into position,repeat the previous steps.
&WARNING:FILL THE SPA WITH WATER BEFORE TURNING ON THE POWER!(See STARTUP AND REFILL PROCEDURES).
Once your spa has been filled with water,turn it on and test all of the circuit breakers.
NOTE:If both breakers immediately trip,verify that the#10 AWG WHITE neutral wire is connected from TB-1 terminal 5 to the N(load neutral)terminal of the 30 amp
subpanel breaker.Each breaker should be tested prior to each use.Here's how:
1. Push the"TEST'button on each GFCI breaker,and observe it click OFF.
2. Wait 30 seconds,then push the breaker switch to the OFF(down)position(to ensure that it has completely disengaged),then push the breaker switch to the ON
(up)position.If you don't wait 30 seconds,the spa's control panel may flash four lines on and off—try again.
If any of the GFCI breakers fails to operate in this manner,your spa may have an electrical malfunction,and you may be at risk of electrical shock.Turn off all circuits
and do not use the spa until the problem has been corrected by an authorized service agent.
SERVICE NOTE:All Caldera spas have diagnostic functions that are displayed on the control panel.Four flashing lines are visible on the control panel if the heater high
limit thermostat has tripped.If the four flashing lines are visible,follow the instructions in the troubleshooting section(See pg.37)to identify and correct the cause.The
four flashing lines will stop flashing once the problem has been corrected.
10
AtL�
a ,. �k"r•z,:.,^.�.. ,`,• ice;,.,,
0 WARNING:Removing or bypassing any GFCI breaker will result in an unsafe spa and will void the spa's warranty,
IMPORTANT:Should you ever find the need to move or relocate your Calderw spa,it is essential that you understand and apply these installation requirements.Your
Caldera spa has been carefully engineered to provide maximum safety against electric shock.Remember,connecting the spa to an improperly wired circuit will negate
many of its safety features.
NOTE:Long wiring runs may require larger-gauge wire than stated.
230 Volt Permanently Connected
WARNING!
THE EXACT PHYSICAL LOCATION OF THE TERMINALS ON THE GFCI BREAKDER
WILL VARY BETWEEN MANUFACTURERS. CONNECTING THE HOT WIRE TO NEUTRAL TERMINAL WILL CAUSE IRREVERSIBLE DAMAGE TO THE CONTROL HEATER
GROUND
m
230V, 50 Amp, O TB1
2—POLE,
CIRCUIT BREAKER
(NON GFCI) t20
a
Lt gs AWG�,4ft1E,NEUTRAL
g10 AWG GflEEN.GROUND" L2 tt12 AWG REDGRD LI y12 AWG BLUE CP 0
/0 AytG BLUE Lt
50A 15 AWG RED,L2 L2 #10 A G RED a
30A Lf 010 AWG BLUE
N q10 AY/G YYFii7E Q
MAIN SERVICE �
ELECTRICAL
PANEL GROUND y10 Alh'G GREEN
0 GRD
*SUBP"EL Mmlmum 5 FEET System Ground Terminal
WITH GFCI The Subpaael must be
within sight of the spa
BREAKERS Do mot exceed 50 FEET.
Less THAN too Fr, CONTROL BOX
Refer to NEC 250-122(table)
NOTE:The wire connections to GFCI breakers are for reference only.Always ensure the white neutral wire is connected to the load neutral of the 30 amp breaker.
*PROVIDED WITH SPA. NOTE: ALL WIRING SHOULD BE COPPER.
POWER CONNECTION ACCESS
CONTROL BOX
DOOR
230V WIRING ACCESS 0--*—DRAIN
OPENINGS ON RIGHT&LEFT
HAND SIDE
7 �
ExIST'l wcc, DWF,L.L WCr-. Al�j��
Additional ;C ( jo
Certification
May Be Required. AUG - 1 2024
Building Department
N Town of Southold
�N
O
N
, _ � N
E.}XISTIQ CT DE r,IG,
lil 4 R' 7314
3 T 10'/i
_ :2
cV-
!? 3
A Hor Tus.
'd
3�0"H GuAP-MAIL W NORM
5,5, :BALUSTEP-S' P 3"
ul �
x SR� �V
4T 2:-q 1440
'
2
u LT
SGA.LE 4- — I-O
I,o ao- a2 60- Fr,
Stratigos Residence
550 Blue Marlin Drive. - • . , N.Y. 11971
S.C.IM, 1000-057.00-0001-027.00 ►