Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
50147-Z
Town of Southold 4/20/2024 a y� P.O.Box 1179 o 53095 Main Rd Southold,New York 11971 i CERTIFICATE OF OCCUPANCY No: 45136 Date: 4/20/2024 THIS CERTIFIES that the building COMMERCIAL ALTERATION Location of Property: 27835 Route 25, Cutchogue SCTM#: 473889 Sec/Block/Lot: 102.-1-18.1 Subdivision: Filed Map No. Lot No. conforms substantially to the Application for Building Permit heretofore filed in this office dated 12/19/2023 pursuant to which Building Permit No. 50147 dated 12/19/2023 was issued, and conforms to all of the requirements of the applicable provisions of the law. The occupancy for which this certificate is issued is: interior alterations to existing school building for Peconic Community School as applied for. _ The certificate is issued to RC Church of Sacred Heart l of the aforesaid building. SUFFOLK COUNTY DEPARTMENT OF HEALTH APPROVAL ELECTRICAL CERTIFICATE NO. 50147 1/4/2024 PLUMBERS CERTIFICATION DATED 4/15/2024 Lu Bugdin A riz ignature o�SufFa���o TOWN OF SOUTHOLD BUILDING DEPARTMENT TOWN CLERK'S OFFICE "o • SOUTHOLD, NY BUILDING PERMIT (THIS PERMIT MUST BE KEPT ON THE PREMISES WITH ONE SET OF APPROVED PLANS AND SPECIFICATIONS UNTIL FULL COMPLETION OF THE WORK AUTHORIZED) Permit#: 50147 Date: 12/19/2023 Permission is hereby granted to: RC Church of Sacred Heart Attn: Michael V Flanagan Esq PO BOX 9023 Rockville Centre, NY 115719023 To: Construct interior alterations to an existing school building to include bathroom alteration, installation of water fountain and electric in basement for GFCI outlets on counter and water fountain power. Fas added to permit need revised plans 12/22/23 FM Visser FAS system plans ok 1/8/24 FM Visser At premises located at: 27835 Route 25, Cutchogue SCTM # 473889 Sec/Block/Lot# 102.-1-18.1 i Pursuant to application dated 12/19/2023 and approved by the Building Inspector. To expire on 6/19/2025. Fees: ELECTRIC $150.00 FIRE ALARM SYSTEM $300.00 CO--COMMERCIAL $100.00 Total: $918.00 Building Inspector o��OF SO!/ryQl � o Town Hall Annex Telephone(631)765-1802 54375 Main Road P.O.Box 1179 Q sean.devlin(&-town.southold.nv.us Southold,NY 11971-0959 Q �yCOU0,� BUILDING DEPARTMENT TOWN OF SOUTHOLD CERTIFICATE OF ELECTRICAL COMPLIANCE SITE LOCATION Issued To: RC Church of Sacred Heart Address: 27835 Route 25 city:Cutchogue St: NY zip: 11935 Building Permit#: 50147 Section: 102 Block: 1 Lot: 18.1 WAS EXAMINED AND FOUND TO BE IN COMPLIANCE WITH THE NATIONAL ELECTRIC CODE Contractor: Electrician: Custom Lighting of Suffolk License No: 38893ME SITE DETAILS Office Use Only Residential Indoor X Basement X Service Commerical X Outdoor 1st Floor X Pool New Renovation 2nd Floor X Hot Tub Addition Survey X Attic Garage INVENTORY Service 1 ph Heat Duplec Recpt 31 Ceiling Fixtures 1 Bath Exhaust Fan 2 Service 3 ph Hot Water GFCI Recpt 8 Wall Fixtures Smoke Detectors Main Panel A/C Condenser Single Recpt Recessed Fixtures CO2 Detectors Sub Panel A/C Blower Range Recpt Ceiling Fan Combo Smoke/CO Transfer Switch UC Lights 2'x2'LED Tile 3 Emergency Strobe Heat Detectors Disconnect Switches 4'LED 2 Exit Fixtures Sump Pump Other Equipment: Notes: Added Outlets & Lighting Inspector Signature: Date: January 4, 2024 S. Devlin-Cert Electrical Compliance Form �oSui:Fot,��o - Town Hell Annex ��O Gyp Telephone(631)765-1802 54375 Main Road a P'.0.Box 1179 to at Southold,NY 11971-0959 �. • " BUILDING DEPARTMENT 4^ APR 1 5 ?_024 TOWN OF SOUTHOLD CERTIFICATION , Date: Building Permit No. Owner: S U�Vw k (Please print) Plumber: L u_K e 'bt tQdo (Please print) I certify that the solder used in the water supply system contains less than 2I10 of 1% lead. I {, (Plumbers Signature) i I Sworn to before me this i day of a+.� I No Public Coun �' � ty DIANNE C VORA NOTARY PUBLIC,STATE OF NEW YORK Registration No.01VI6442157 Qualified in Suffolk County Commission Expires October 112026 SOUlyO6 / ' TOWN OF SOUTHOLD BUILDING DEPT. cou►m1 631-765-1802 'INSPECTION [ ] FOUNDATION 1ST [ ] ROUGH PL13G. [ ] FOUNDATION 2ND [ ] INSULATIOWCAULKING [ ] FRAMING /STRAPPING [ ] FINAL s", [ ] FIREPLACE & CHIMNEY [ J FIRE SAFETY INSPECTION [ ] FIRE RESISTANT CONSTRUCTION [ ] FIRE RESISTANT PENETRATION [ ] ELECTRICAL (ROUGH) [ ] ELECTRICAL (FINAL) [ ] CODE VIOLATION [ ] PRE C/O [ ] RENTAL REMARKS: 14r � �� �o� ►C-/ �' 1Olulj.%� D�c3 7o ,¢r s 31�6' 5�9iiS, Sy���� ���� �6oG�L Qo ✓� �6aCGoQs�`e f car M,V on L,#/! ce,%a J r�1uv( F'n�5'�'�S �loafi lR» f.4 DATE 17i) Z INSPECTOR ( VM, ��5 q-7 �0--c- A- TOWN OF SOUTHOLD BUILDING DEPT. 631-765-1802 INSPECTION [ ] FOUNDATION 1ST [ ] ROUGH PLBG. [ ] FOUNDATION 2ND [ ] INSULATION/CAULKING [ ] FRAMING /STRAPPING [ ] FINAL [ ] FIREPLACE & CHIMNEY [ ] FIRE SAFETY INSPECTION [ ] FIRE RESISTANT CONSTRUCTION [ ] FIRE RESISTANT PENETRATION [ ] ELECTRICAL (ROUGH) ELECTRICAL (FINAL) [ ] CODE VIOLATION [ ] PRE C/O [ ] RENTAL REMARKS: Pbu /0�- feA n - DATE INSPECTOR gf SOUtyolo # # 'TOWN OF SOUTHOLD BUILDING DEPT. cou 631-765-1802 oiw� INSPECTION [ ] FOUNDATION 1ST [ ] ROUGH PLBG. [ ] FOUNDATION 2ND [ ] ULATION/CAULKING [ ] FRAMING /STRAPPING [ FINAL [ ] FIREPLACE & CHIMNEY [ ] FIRE SAFETY INSPECTION [ ] FIRE RESISTANT CONSTRUCTION [ ] FIRE RESISTANT PENETRATION [ ] ELECTRICAL (ROUGH) [ ] ELECTRICAL (FINAL) [ ] CODE VIOLATION �,� [ /] PRE C/O [ ] RENTAL REM KS: .V GA�V DATE q INSPECTORqu �Y r 1 f APR 1 2024 •�L+¢Je: ..a ..... r_. :1 -- / V. • 0 WM 1149 Old Country Road " lighthouse Suite D5 Riverhead, New York 11901 (631 ) 727-2728 info@lighthousesecurityinc.com RE:Peconic Community School December 29,2023 Dear Fire Marshal Visser, Please be advised that the following work has been completed on December 29, 2023 at the Peconic Community School located at 27685 Main Road in Cutchogue,New York,as requested: • Installation of fire documentation box next to fire alarm control panel. • Installation of additional fire strobe light appliance in teachers'meeting room. • Installation of fire smoke detector in place of existing fire heat detector in teachers' meeting room. • Removal of all non-system devices. • Revised plans to include teachers'meeting room dimensions to scale. • Stamped and signed battery calculations document. • Revised addressable fire alarm system zone identification list. • All local and New York State Fire Code requirements and regulations to be included in Fire Marshal's stamp box on plans. For additional information if necessary,please call our office at(631)727-2728. Respectfully, Thomas Santacroce President Lighthouse Security Inc., is licensed with the NY.Department of State#12000022174 12/29/23 14:49 Subscriber Information Report Page: 1 Account Number: 00538398 Premises________________________________ Mailing Address=====___________________ PECONIC COMMUNITY SCHOOL 27685 MAIN ROAD CUTCHOGUE NY 11935 USA County. . . . . . . . . . . . . . . . . . . . . . . . . . Suffolk Sort By Name. . . . . . . . . . . . . . . . . . . . PECONIC COMMUNI Panel Type. . . . . . . . . . . . . . . . . . . . . Start Date. . . . . . . . . . . . . . . . . . . . . . 11/10/23 Last Modified Date 12/29/23 14:49 Active (Y/N) . . . . . . . . . . . . . . . . . . . . Y Time Zone. . . . . . . . . . . . . . . . . . . . . . . EST Any Signal a Test. . . . . . . . . . . . . . . N Test Span. . . . . . . . . . . . . . . . . . . . . . . NONE Zone Test. . . . . . . . . . . . . . . . . . . . . . . N Signal Descriptions Signal Code Event Type Event Description Call List Req ------------ -------------------- ------------------------------ ----------- --- 1 - MAIN OFFICE SMOKE DEFLT OPR 2 - HALLWAY BY RESTROOM SMOKE DEFLT OPR 3 - BOYS RESTROOM SMOKE DEFLT OPR 4 - GIRLS RESTROOM SMOKE DEFLT OPR 5 - HALLWAY BY CLASSROOM SMOKE DEFLT OPR 6 - HALLWAY BY CLASSROOM SMOKE DEFLT OPR 7 - HALLWAY BY CLASSROOM SMOKE DEFLT OPR 8 - HALLWAY BY CLASSROOM SMOKE DEFLT OPR 9 - HALLWAY BY REAR EGRESS SMOKE DEFLT OPR 10 - BASEMENT MEETING ROOM SMOKE DEFLT OPR 11 - BASEMENT MEETING ROOM SMOKE DEFLT OPR 12 - BASEMENT MEETING ROOM SMOKE DEFLT OPR 13 - BASEMENT RESTROOM SMOKE DEFLT OPR 14 - 2ND FLOOR HALLWAY SMOKE DEFLT OPR 15 - 2ND FLOOR RESTROOM SMOKE DEFLT OPR 16 - BASEMENT MECHANICAL ROOM HEAT DEFLT OPR 17 - BASEMENT MEETING ROOM SMOKE DEFLT OPR 18 - 2ND FLOOR KITCHEN HEAT DEFLT OPR 201 - MAIN ENTRANCE PULL DEFLT OPR 202 - REAR EGRESS BY STAIR PULL DEFLT OPR 203 - BASEMENT STAIRWELL PULL DEFLT OPR 204 - 2ND FLOOR HALLWAY PULL DEFLT OPR 205 - HALLWAY BY CLASSROOM CO DEFLT OPR 206 - HALLWAY BY CLASSROOM CO DEFLT OPR 207 - BASEMENT CO DEFLT OPR -208 - 2ND FL HALLWAY CO DEFLT OPR LIGHTHOUSE SECURITY 1149 OLD COUNTRY ROAD SUITE D-5 RIVERHEAD, NY 11901 LIGHTHOUSE SECURITY PECONIC COMMUNITY SCHOOL 1149 OLD COUNTRY ROAD 27685 MAIN ROAD SUITE D-5 CUTCHOGUE, NY 11935 USA RIVERHEAD, NY 11901 PECONIC COMMUNITY SCHOOL Account: 00538398 27685 MAIN ROAD From: 12/18/23 at 11:29 CUTCHOGUE , NY 11935 USA To: 12/18/23 at 14:00 PANEL TYPE: Date Time Signal Information Account: 00538398 -------- -------- ----------------------------------------------------------- 11:29:22 TESTING OF ENTIRE SYSTEM - ADDED TESTING STARTS 12/18/23 11:29 TESTING ENDS 12/18/23 19:29 VALID ALL DAYS OF THE WEEK REASON: TOM 11:31:30 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 12 97 FIRE ALARM AREA 97 BASEMENT MEETING ROOM SMOKE 11:32:08 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 11 97 FIRE ALARM AREA 97 BASEMENT MEETING ROOM SMOKE 11:32:39 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 a. SIGNAL RECEIVED: (E110 ) E110 13 97 z. FIRE ALARM AREA 97 BASEMENT RESTROOM SMOKE 11:39:42 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 16 97 FIRE ALARM AREA 97 BASEMENT MECHANICAL ROOM HEAT 11:42:27 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E115 ) E115 203 97 FIRE-PULL STATION - AREA 97 BASEMENT STAIRWELL PUL BASEMENT STAIRWELL PULL SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 17 97 FIRE ALARM AREA 97 BASEMENT UTILITY ROOM HEAT 11:45:02 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 12/18/23 A 1 1 A c t i v i t y R e p o r t Page: 2 Date Time Signal Information Account: 00538398 -------- -------- ----------------------------------------------------------- SIGNAL RECEIVED: (E110 ) E110 10 97 FIRE ALARM AREA 97 BASEMENT MEETING ROOM SMOKE 11:46:36 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 9 97 FIRE ALARM AREA 97 HALLWAY BY REAR EGRESS SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 8 97 FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SMOKE 11:47:30 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 7 97 FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SMOKE 11:49:05 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 11:49:05 SIGNAL RECEIVED: (E110 ) E110 6 97 FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SMOKE 11:50:21 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 4 97 FIRE ALARM AREA 97 GIRLS RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 5 97 FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SMOKE 11:55:40 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 2 97 FIRE ALARM AREA 97 HALLWAY BY RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 1 97 FIRE ALARM AREA 97 MAIN OFFICE SMOKE 11:57:20 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 14 97 FIRE ALARM AREA 97 2ND FLOOR HALLWAY SMOKE 11:57:51 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 15 97 FIRE ALARM AREA 97 2ND FLOOR RESTROOM SMOKE 11:58:45 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 3 97 FIRE ALARM AREA 97 BOYS RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E115 ) E115 204 97 FIRE-PULL STATION - AREA 97 2ND FLOOR HALLWAY PULL 11:59:20 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E110 ) E110 18 97 FIRE ALARM AREA 97 2ND FLOOR KITCHEN HEAT SIGNAL RECEIVED: (CALLS) CALLS y 12/18/23 A 1 1 A c t i v i t y R e p o r t Page: 3 Date Time Signal Information Account: 00538398 -------- -------- ----------------------------------------------------------- SIM ID NUMBER 089148000008243983341 SIGNAL RECEIVED: (E115 ) .E115 201 97 FIRE-PULL STATION - AREA 97 MAIN ENTRANCE PULL 12:00:33 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E115 ) E115 202 97 FIRE-PULL STATION - AREA 97 REAR EGRESS BY STAIR P REAR EGRESS BY STAIR PULL 12:02:57 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E401 ) E401 0 00 OPENING BY USER USER 0 AREA 00 12:02:57 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 1 97 RESTORE FIRE ALARM AREA 97 MAIN OFFICE SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 2 97 RESTORE FIRE ALARM AREA 97 HALLWAY BY RESTROOM SMO HALLWAY BY RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 3 97 RESTORE FIRE ALARM AREA 97 BOYS RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 4 97 RESTORE FIRE ALARM AREA 97 GIRLS RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 5 97 RESTORE FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SM HALLWAY BY CLASSROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER- 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 6 97 RESTORE FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SM HALLWAY BY CLASSROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 7 97 RESTORE FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SM HALLWAY BY CLASSROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 8 97 RESTORE FIRE ALARM AREA 97 HALLWAY BY CLASSROOM SM HALLWAY BY CLASSROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 9 97 RESTORE FIRE ALARM AREA 97 HALLWAY BY REAR EGRESS HALLWAY BY REAR EGRESS SMOKE 12:03:29 SIGNAL RECEIVED: (CALLS) CALLS i 12/18/23 A 1 1 A c t i v i t y R e p o r t Page: 4 Date Time Signal Information Account:- 00538398 -------- -------- ----------------------------------------------------------- SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 10 97 RESTORE FIRE ALARM AREA 97 BASEMENT MEETING ROOM' S BASEMENT MEETING ROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 11 97 RESTORE FIRE ALARM AREA 97 BASEMENT MEETING ROOM S 12:03:29 ' BASEMENT MEETING ROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 12 97 RESTORE FIRE ALARM AREA 97 BASEMENT MEETING ROOM S BASEMENT MEETING ROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 13 97 RESTORE FIRE ALARM AREA 97 BASEMENT RESTROOM SMOKE SIGNAL RECEIVED: ' (CALLS) CALLS SIM ID NUMBER O'89148000008243983347 SIGNAL RECEIVED: (R110 ) R110 14 97 RESTORE FIRE ALARM AREA 97 2ND FLOOR HALLWAY SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 15 97 RESTORE FIRE ALARM AREA 97 2ND FLOOR RESTROOM SMOK 2ND FLOOR RESTROOM SMOKE SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 16 97 RESTORE FIRE ALARM AREA 97 BASEMENT MECHANICAL ROO BASEMENT MECHANICAL ROOM HEAT SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 17 97 RESTORE FIRE ALARM AREA 97 BASEMENT UTILITY ROOM H BASEMENT UTILITY ROOM HEAT SIGNAL RECEIVED: (CALLS) CALLS SIM ID, NUMBER 089148000008243983347 SIGNAL RECEIVED: (R110 ) R110 18 97 RESTORE FIRE ALARM AREA 97 2ND FLOOR KITCHEN HEAT SIGNAL RECEIVED:- (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R115 ) R115 201 97 RESTORE PULL STATION AREA 97 12:04:18 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R115 ) R115 202 97 RESTORE PULL STATION AREA 97 , SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R115 ) R115 203 97 RESTORE PULL STATION AREA 97 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 5 ' 12/18/23 A l l A c t i v i t y R e p o r t Page: 5 Date Time Signal Information Account: 00538398 -------- -------- ----------------------------------------------------------- SIGNAL RECEIVED: (R115 ) R115 204 97 RESTORE PULL STATION AREA 97 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 12:04:18 SIGNAL RECEIVED: (E162 ) E162 205 97 CARBON MONOXIDE DETECTED - AREA 97 HALLWAY BY CLAS HALLWAY BY CLASSROOM CO 12:04:50 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E162 ) E162 206 97 CARBON MONOXIDE DETECTED - AREA 97 HALLWAY BY CLAS HALLWAY BY CLASSROOM CO 12:06:18 SIGNAL- RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E162 ) E162 207 97 CARBON MONOXIDE DETECTED - AREA 97 BASEMENT CO 12:09:33 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E162 ) E162 208 97 CARBON MONOXIDE DETECTED - AREA 97 2ND FL HALLWAY 2ND FL HALLWAY CO l 12:13:32 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R162 ) R162 205 97 CARBON MONOXIDE RESTORE AREA 97 SIGNAL RECEIVED: (CALLS) CALLS SIM ID, NUMBER 089148000008243983347 SIGNAL RECEIVED: (R162 ) R162 206 97 CARBON MONOXIDE RESTORE AREA 97 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R162 ) R162 207 97 CARBON MONOXIDE RESTORE AREA 97 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (R162 ) R162 208 97 CARBON MONOXIDE RESTORE AREA 97 SIGNAL RECEIVED: (CALLS) CALLS SIM ID NUMBER 089148000008243983347 SIGNAL RECEIVED: (E401 ) E401 0 00 OPENING BY USER USER 0 AREA 00 12:53:18 AUDIT DETAILS FOR Account Authorities Submitted Via Matrix Non Queued ADDED FD CODE ssfh3- -SOUTHOLD NY FIRE & R@ (631) 765-0038 12:53:20 AUDIT DETAILS FOR Account Authorities Submitted Via Matrix Non Queued ADDED FD CODE ssfh3- -SOUTHOLD NY FIRE & R@ (631) 765-0038 FIELD INSPECTION REPORT DATE COMMENTS ro FOUNDATION (1ST) � y ------------------------------------ C FOUNDATION (2ND) � 1 z o � _ � y ROUGH FRAMING& V' PLUMBING y -_ [ram \ INSULATION PER N.Y. . STATE ENERGY CODE i Owe. G, b a✓ $ PLC�l oe� ��t�te✓ S mow lm�( FINAL ADDITIONAL COMMENTS 0,- a`� �d C! � 2e c- /v� 3 °ik I (&(V-)����S' y r �c S i4oLeA U-/� end * �. Z " x ---- d b b. » TOWN OF SOUTHOLD—BUILDING DEPARTMENT Town Hall Annex 54375 Main Road P. O. Box 1179 Southold,NY 11971-0959 oy�o• �ao�� Telephone(631) 765-1802 Fax (631) 765-9502 https://www.southoldtownny.gov Date Received APPLICATION FOR BUILDING PERMIT M'Fl v L=7 1 U Lc D For Office Use Only PERMIT NO. 50 Building Inspector: `-' DEC 2 6 2023 Applications and forms must be filled,out in thementirety:Incomplete' applications will not"be"accepted. Where the Applicant is-not the,owner,an y v,�.,F})'f °t�a Owner's Authorization form(Page 2)shall be completed: " ;� ,; :r"` � i5 Date: )jl�- OWNER(S))/OF PROPERTY:, j Name: �'I �� p4 Sc,�aCc� ��rd i— SCTM#1000- 1 0-)— Project Address: P AX 013 Phone#: Email: Mailing Address: p� (9) 1 023 oct(%;i IQ CPnljer �y � (S1 I .CONTACT-PERSON: t Name: u SS E L k1,0V,' C 60 Mailing Address: C6 Phone#: Clo"t,Cj "LOZ Email: o'K4e(? 1`C(►�►or,c� Jec C-0 j , CaIw. DESIGN PROFESSIONAL INFORMATION: Name: Mailing Address: Phone#: Email: CONTRACTOR INFORMATION:.- _ Name: Q2 L i C* 6 —7 I ll,\ Mailing Address: 11 ,Q, 0ox M46t'v' Ny Phone#: 53 -5q1 Email: .DESCRIPTION OF'PROPOSED CONSTRUCTION ❑`New Structure❑Addition 4ZAlteration ❑Repair ❑Demolition Estimated Cost of Project: ❑Other �i�S�2� I 3 ,n,ew 51,6,S V1f.c,• wa{ey C'-41•:h I Of kff JgnAeS $ 2,11006 .ot? Will the lot be re-graded? ❑Yes ONO Will excess fill be removed from premises? []Yes ❑No 1 , PROPERTY'INFORMATION - Existing use of property: cG��n Intended use of property: Zone or use district in which`/premises is situated: Are there any covenants nd restrictions with respect to this property? ❑Yes covenants IF YES, PROVIDE A COPY. 0;,heck Box'After'Reading: The'owrier/contractor/design professional.is responsible•fot all drainage and storiri water issues as,provided by ; Chapter 236 of the Town Code.APPLICATION IS HEREBY MADE to ihe'Building DepartmenYfor the Issuance,of a Building Permit pursuant to the Building Zone•_ Ordinance of the Town of Southold,Suffolk,County,New Y(irk'and other applicable Laws,Ordinances'or Regulations,for the construction of building's,: ''additions,alterations or.for removal or demolition as herein.described:The 'icant.agrees to comply with all applicable laws,ordinances,building code; . housing code and regulations'and to admit authorized inspectors on premises and in building(s)for necessary inspections.False statements made herein are . punishable as a,Class A misdemeanor pursuant to Section 210AYof the New York State Penal Law. Application Submitted By prin name): D 5 ��E N SOA L OAuthorized Agent ❑Owner Signature of Applicant: Date: )212-1 /13 STATE OF NEW YORK) SS: COUNTY OF ) ( 9 0, -Q,�- being duly sworn,deposes and says that(s)he•is the applicant (Name of individual signing contract)above named, (S)he is the (Contractor,Agent,Corporate Officer,etc.) of said owner or owners, and is duly authorized to perform or have performed the said work and to make and file this application;that all statements contained in this application are true to the best of his/her knowledge and belief;and that the work will be performed in the manner set forth in the application file therewith. Sworn efore me this �2 day of QW-V b Pig(day N tart'Public GEORGIA MALONE GEORGIA MALONe, Notary Public,Mate of New Vb* .PR®PE�Tl° ®INNER AIDTH®R9ZATION Res,No,02MA04 39 Notary Public,State of N�n+Y Quslifiod In New York County Reg.,No.02MA618W39 (Where the applicant is not the owner) Commission Expires April 14,203�Z� Qualified in New York County Commission Expires April''t4,2w - I� residing- at o� ! / //(�i,� /�-f//(� do hereby authorize P!'O C-a V to apply on my behalf to the Town of Southold Building Department for approval as described herein. Owner's Signature Date Print Owner's Name 2 and fSO .......... . . . a�a BUILDING DEPARTMENT-Electrical Inspector TOWN OF SOUTHOLD Town Hall Annex-54375 Main Road - PO Box 1179 Southold, New York 11971-0959 Telephone (631) 765-1802 - FAX(631) 765-9502 _ roQerria'�i southoldtownny.gov seandtc—southoldtownny.gov APPLICATION FOR ELECTRICAL INSPECTION ELECTRICIAN INFORMATION (Ail Information Required) Date: Company Name: Custom Lighting of Suffolk Inc Electrician's Name: Benjamin Doroski License No.: 38893-ME Elec. email:CLOS5170@gmail.com Elec. Phone No: 631-298-4588 01 request an email copy of Certificate of Compliance Elec. Address.: PO Box 1698 Mattituck NY 11952 JOB SITE INFORMATION (All Information Required) Name.-Pe ,C_ 0 f-n On Address: Cross Street: Phone No.: Bldg.Permit#: `j 01 y.- email: Tax Map District: 1000 Section: D a Block: l Lot: BRIEF DESCRIPTION OF WORK, INCLUDE SQUARE FOOTAGE (Please Print Clearly): Square Footage: Circle All That Apply: Is job ready for inspection?: YES.[]NO ®Rough In Final Do you need a Temp Certificate?: ® 'YESIRNO Issued On Temp Information: (All information required). Service SizeF-11 Ph❑3 Ph Size: A #Meters Old Meter# ❑New Service❑Fire ReconnectOFlood Reconnect❑ServiceReconnect[lUnderground❑Overhead # Underground Laterals R 1 2 0 H Frame Pole Work done on Service? 0 Y DN Additional Information: Ml PAYMENT DUE WITH APPLICATION `5 DEC 1 9 2023 p C+rJi b.iC ,ii Md nt.a 40 —cA,0) cl n d �FFp BUILDING DEPARTMENT-Electrical Inspector a� TOWN OF SOUTHOLD Town Hall Annex-54375 Main Road - PO Box 1179 Southold, New York 11971-0959 per. Telephone (631) 765-1802 - FAX(631) 765-9502 Ip �' rogerrc@c-southoldtownny.gov seandCa�southoldtownny.Qov APPLICATION FOR ELECTRICAL INSPECTION ELECTRICIAN INFORMATION (Ail Information Required) Date: Company Name: Custom Lighting of Suffolk Inc Electrician's Name: Benjamin Doroski License No.: 38893-ME Elec. email:CLOS5170@gmail.com Elec. Phone No: 631-298-4588 '101 request an email copy of Certificate of Compliance Elec. Address.: PO Box 1698 Mattituck NY 11952 JOB SITE INFORMATION (All Information Required) Name }PC c_ I C- C 0 m fy'A Address: Cross Street: , p i- Phone No.: i BIdg.Permit#: 5 IJ( 9 -1 email: Tax Map District: 1000 Section: p OL Block: 0` Lot: / .. BRIEF DESCRIPTION OF WORK, INCLUDE SQUARE'FOOTAGE (Please Print Clearly): S uare Footage: Circle All That Apply: Is job ready for inspection?: rV YES❑NO ®Rough In Final Do you need a Temp Certificate?: ® YESKNO Issued On Temp Information: (All information required) Service Size❑1 Ph F-�3 Ph Size: A # Meters Old Meter# ❑New service[]Fire Reconnect[ Reconnect®Service Reconnect®Underground❑Overhead # Underground Laterals 1 F12 F1 H Frame Pole Work done on Service? Y N Additional Information: J PAYMENT DUE WITH APPLICATION ' O E C 1 9 2023 PERMIT H Address: Switches Outlets / r, GFI's Surface Sconces H H's UC Lts Fans Fridge HW Exhaust ; Oven W/D Smokes DW Mini Carbon Micro Generator Combo Cooktop Transfer �\C AH Hood Service Amps Have Usec )pecial: :omments o� F��coo TOWN OF SOUTHOLD—FIRE.MARSHAL s2 Town Hall Annex 54375 Main Road P. O. Box 1179 Southold,NY 11971-0959 Telephone (631) 765-1802 Fax(631) 765-9502 htt6s://www.southoldtownny.gov FIRE PROTECTION SYSTEM PERMIT Date Received APPLICATION 5 I q For Office Use Only HCc;�ZE`OVIE-7�' ���PERMIT NO. I Building Inspector:�V D I Applications and forms must be filled out in their entirety.Incomplete -� pp �' p DEC 1 1 2023 applications will not be accepted.WORK IS NOT TO BE STARTED prior to the approval of plans and issuance of a permit. Has a building permit been obtained for this project? ❑Yes ®No B' `DVYO DEPT. If yes,building permit# T01:1' Date: PROJECT INORMATION: Project Address: 27835 Main Road SCTM# 1000-102-01-18.1 City: Cutchogue _.__. __. _._.._. _ Zip: 11935 CONTACT PERSON INFORMATION: Name: Kathryn Casey Quigley Mailing Address: 359 Main Road, Aguebogue, NY 11931 Phone#: 631-779-2934 Email:kathryn@peconiccommunityschoolorg Preferred contact method(select one): ElPhone ❑Email CONTRACTOR INFORMATION: Name: Lighthouse Security,lop. -T Contractor License#: 12000022174 Mailing Address: 1149 Old Country_ Road, Suite D5, Riverhead, New York„11901 Phone#: 631-831-5822 .. Email:info@lighthousesecurity_inc.com SCOPE OF WORK: Occupancy Description: ❑Assembly ❑Business ®Education ❑Factory/Industrial ❑Institutional ❑Mercantile ❑Residential ❑ Storage Description of work: Installation of an addressable fire/carbon monoxide detection system. 19 New System ❑ Existing System Modification Sprinkler/Standpipe/Water Supply Fire Alarm/CO Detection Systems Other Fire Protection Systems . (Check all that apply) (Check all that apply) (Check all that apply) ❑NFPA 13,13D or 13R System ❑Manual ®Automatic ❑ Smoke Control ❑Standpipe ❑ Fire Pump ❑Protected Premises(local) ❑Wet or Dry Chemical/Clean ❑Supervising station Agent Number of sprinkler heads: ®Central Station ❑Kitchen hood/exhaust ❑ Other Floor Area(sq. ft.): 1 B Check Box After Reading: I,the undersigned,,understand that the issuance of a'permit for the type which is herein applied for is based on the agreement to conform to all regulations and requirements.I further understand that non-compliance of said requirements,by myself or any officer or employee of,the firm or individual listed as the applicant on this form,shall be cause for revocation of said permit.Upon revocation of said permit the applicant or any employee of the applicant shall be prohibited to conduct such work for which this permit was issued.The reissuance of a permit shall be based upon review of the circumstances leading tathe revocation.'Any false statement(s)made herein are punishable as a Class A misdemeanor pursuant to Section 216.45 of the Penal Law Application Submitted By(print name): Thomas Santacroce ❑Authorized Agent ®Owner Company(if applicable): Lighthouse Security Inc. Applicant Signature: Date: 1 11 2/07/23 FIRE PROTECTION SYSTEM PERMIT APPLICATION SUBMITAL INSTRUCTIONS Submit application only after reviewing the requirements for the specific permit for which you are applying(click the applicable link below). r • FIRE ALARM/CARBON MONOXIDE DETECTION SYSTEM SUBMITTAL GUIDELINES • FIRE SPRINKLER SYSTEM SUBMITTAL GUIDELINES • FIXED FIRE SUPPRESSION HOOT!& EXHAUST SYSTEMS SUBMITTAL GUIDELINES FEES A$300 permit fee is required for a non-residential permit.A$100 Certificate of Occupancy fee is required if the project is not part of an existing open building permit. All checks should be made payable to the Town of Southold. Permits,once issued,shall at all times be kept on the premises designated thereon with a copy of approved drawings and all related documentation required to obtain said permit.Installations subject to final testing,inspection and approval.Arrangements for testing/inspection shall be made by contacting the Town of Southold Building Department(631)765-1802. FOR OFFICE USE ONLY Amount Paid: Check No.: TM: Permit No.: Date: Exp..Date: 2 Vc-r-I-i cal yab bar re u i rfd as 'Ro aol Pcr -TCC. A I 1 " 2coq. APPROVED AS NOTED SATE: .P. . 5 36" MIN. GRAB BAR 33____. Co Y: 5' - 0" 42" MIN. GRAB BAR NOTIFY BUILDING I EPARTMENTAT 631-765-1802 8AM O 4PM FOR THE FOLLOWING INSPECTIONS' 6' - $„ FOUNDATION-TWO REQUIRED FOR POURED NCRETE ROUGH-FRA lNG&PLUMBING o INSULATION ' FINAL-CONSIRUMON MUST N j "' BE COMPLETE FOR C.O. ALL CONSTRUCTION SHALL MEET THE REQUIREMENTS Of THE CODES OF NEW 2' - 811 YORK STATE. NC RESPONSIBLE FOR DESIGN OR CON UCTION ERRORS EL CTRICAL 80 INSPEC ION REQUIRED a, I PLUMBER CERTIFICATION ON LEAC CONTENT BEFORE CERTIFIC TE OF OCCUPANCI I I CV ' CLOSET SOLDE I USED IN WATER I I SUPPLY SYSTEM CANNOT _ EXCEE10 2/90 OF 1% LEAD. I I N I I �i i BASEBOARD HEATER— "' COMPLY WITH ALL CODES OF 36" DOOR NEW YORK SJATTOWN CODES AS REQ IREDCONDITIONS 0 1 WN , TOWNP�AN�INGMM GIRLS RESTROOM - ENLARGED PLAN PLUMBING Damon 31811 = 11-011 L PL�JM6gG-WASTE f tER'LIVES 4EED TESTING BEFORE COVERING SQL}{ LDHP SCHD Peconic Community School DATE 219124 BATHROOM RENOVATION SCALE 318" = 1'-0" 27835 Main Rd, Cutchogue, NY DRAWN BY SHEET NO. A-101 CL U BOYS RESTROOM �o GIRLS RESTROOM L� ELECT. 1 CL CL OFFICE OFFICE l PARTIAL PLAN 3132" = V-0„ OCCUPANT NOTES OCCUPANCY GROUP SQUARE FOOTAGE OCCUPANT LOAD FACTOR OCCUPANT LOAD IBC 1004.5 EDUCATIONAL - CLASSROOM BASEMENT: 0 11ST FLR: 5,279 NET 12ND FLR: 0 20 NET 264 PEOPLE* IBC 305.1 TOTAL:5,279 BUSINESS - OFFICE BASEMENT: 01 1ST FLR: 384 GROSS 12ND FLR: 773 GROSS 150 GROSS 8 PEOPLE IBC 304.1 TOTAL:1,157 *PER LOCAL ZONING ORDINANCE §280-13-B, MAXIMUM OCCUPANCY IS DETERMINED BY OVERALL LOT SIZE AND IS CAPPED AT 125 PUPILS. FIXTURE NOTES OCCUPANCY GROUP MINIMUM#OF REQUIRED FIXTURES FIXTURES REWD TOTAL REWD TOTAL FIXTURES PROVIDED IPC 403.1 EDUCATIONAL WC: 1 PER 50, LAV: 1 PER 50 WC: 5.3, LAV: 5.3 WC: 6, LAV: 6 WC: 5 (F) + 3 (M) + 3 URINALS + 3 SINGLE-USER, LAV: 2.(F) + 2 (M) + 3 (SINGLE-USER) BUSINESS WC: 1 PER 25, LAV: 1 PER 40 WC: 0.3, LAV: 0.2 Peconic Community School DATE 219124 BATHROOM RENOVATION - FIXTURE COUNT SCALE As indicated 27835 Main Rd, Cutchogue, NY DRAWN BY SHEET NO. A-100 remove toilet and partition CL WC 10 16"F t[R3N TALLNEW CL 22'-0" NITY TOP IIIIIII e'-6" M1 INSTALL NEW CL I I I I I I I co IVL VANITY TOPMW r 1 a m �• f N � � 9 6 ` Office Offite 12 13 22U-SF IMF 13'-4112" -2 13'-4" r 38'- 112" C7� 9'-11rr 2(r-Ur 17'-4lir j UP _ E C E WE ') 5-3• F13*-5" stoma DEC 2 2 2023 m N nil 1 .0vv o,Southold ' N 0 P-2- 38'-011t LL GL L 53'-4_ Install new lower IL cabinet bases and sink €� M Kadtip�rtpou � up AT 4 55, 4. Install Ne Water Fountain and t<vo laundrysi 0 BASEMENT FLOOR -SCHO Ila,=i'I FIRE ALARM NOTES THE FIRE ALARM AND SMOKE DETECTION SYSTEM SHALL BE 1. ALL SMOKE DETECTORS SHALL BE MOUNT NO CLOSER INSTALLED MAINTAINED THAN 36" FROM ANY HVAC SUPPLY OR RETURN DUCT AND TESTED IN COMPLIANCE DIFFUSER. PULL STATIONS TO BE MOUNTED 4'0" A.F.F. TO CENTER OF DEVICE AND WITHIN 5' OF ASSOCIATED WITH THE FLOOWING CODES DOORWAY. HORN/STROBE AND STROBE DEVICES TO BE AND REGULATIONS• MOUNTED 6'8" A.F.F. TO CENTER OF DEVICE. HORNS 2016 NFPA-72 5C0 RATED AT 85 DB AND STROBES ARE 15/75 CANDELA CL CLASS ROOM CLASS ROOM CLASS ROOM CLASS ROOM 2. ALL DEVICES SHALL BE MOUNTED ON APPROPRIATE • 2017 RNPA-NEC-70 S (11-0'STC) (11-0 STC) (11'-0"STC) (11-0 STC) BOXES SO THEY ARE ELECTRICALLY AND • 2020 NYS BUILDING CODE TOILET STOR. STOR. MECHANICALLY SECURE . 2020 NYS FIRE CODE ]SC�r �� � ' � 3. ALL EXPOSED WIRING UNDER EIGHT FEET SHALL BE IN F PROTECTIVE CONDUIT. OFFICE 4. ALL FIRE ALARM WIRING SHALL BE APPROVED FOR THE SPECIFIC TYPE OF JOB CONDITION WIRE SPEC. CHART 5. FIRE ALARM INITIATING CIRCUIT SHALL BE MINIMUM 18 GAUGE SOLID CL. 6. ALL NOTIFICATION APPLIANCE WIRING SHALL BE #18 AWG FPL WERE:ADDRESS LOOP MINIMUM 16 GAUGE SOLID #14 AWG FPL WIRE: SIGNAL CIRCUIT 7. ALL SMOKE AND HEAT DETECTORS MOUNTED IN HUNG F CEILINGS SHALL BE MOUNTED AT THE HIGHEST POINT #12 AWG FPL WIRE: 120VAC/ GRD. ATTACHED TO THE UNDERSIDE OF THE ROOF DECK HALLWAY � HALLWAY 8. ALL WIRING SHALL BE SUPPORTED SO AS NOT TO REST 9'-6"STC o\/��c7/P/\ S s `/V �� �®o (9'-6"STC) D ON THE HUNG CEILING 9. ALL MANUFACTURERS INSTALLATION REQUIREMENTS SHALL BE STRICTLY ADHERED TO TYP. DEVICE LOCATION 10. ALL N.F.P.A. 72, LOCAL, STATE, A.D.A, AND VII LAGE CL. N CODES SHALL BE STRICTLY ADHERED TO AIR REGISTER sMo 11. PROJECT ARCHITECTS MUST APPROVE ANY CHANGE IN 3WMINMiJM�nETECTOR DRAWING OFFICE K n n CL. 12. A fful LL WORK SHALL BE DONE BY A NEW YORK STATE LICENSED FIRE ALARM INSTALLATION COMPANY U �S 13. ALL WORK SHALL BE COMPLETED IN A xoRN STROBE CLASS ROOM CLASS ROOM CLASS ROOM CLASS ROOM STROBE CRAFTSMAN-LIKE MANNER AND SHALL BE PLEASANT &sTRosB nsvlcE (11'-0"STC) (11--0"STC) (11'-0"STC) �,Sco ]5C� 5C ]� (11'-0]5 STC) TO THE EYE � 14. CENTRAL STATION MONITORING BY ALARM-TECH CL. LL� R, � E R (631)-232-0900 S -- n I 15. 24 HOUR CENTRAL STATION AND ALARM REPAIR PULL STATION w CONTACT TELEPHONE NUMBERS ARE TO BE DISPLAYED TOILET I I ON THE ALARM PANEL a w m I �ARTITION WALLS 16. SYSTEM MODIFICATIONS AND COMPONENTS ARE w NOT TO CEILING SUBJECT TO ADDITION, DELETION, MODIFICATION, OR a 0 TOILET I I ALTERATION AT THE TIME OF FINAL INSPECTION, IF FOUND TO BE INADEQUATE BY THE FIRE MARSHAL FLOOR REVISIONS FIRST FLOOR FIRE ALARM PLAN # DATE ISSUE/REVISION/NOTES SEQUENCE OF OPERATIONS 1 12/712023 SUBMITTED FOR REVIEW SCALE: 1/8"=1' 1. WHEN ANY INITIATING DEVICE IS ACTIVATED, THE 2 12127/2023 SUBMITTED FOR REVIEW FOLLOWING WILL OCCUR: A.HORNS WILL SOUND A TEMPORAL 3 CODE B. STROBES WILL FLASH DEVICE LEGEND SITE PLAN C.FANS WILL SHUT DOWN D.THE DEVICE IN ALARM WILL BE LISTED AT THE CST ANNUNCIATOR E.AN ALARM SIGNAL WILL TRANSMIT TO THE 2� CENTRAL STATION DETAILS: UP SYMBOL QTY DESCRIPTION PART NUMBER 1p'A 2. WHEN THE ALARM IS SILENCED, THE FOLLOWING WILL C.T.CEILING TILE S.R.SHEET ROCK LIBRARY TOILET OCCUR: (8'-0"C.T.) A.HORNS WILL SILENCE FACP 1 FIRE ALARM CONTROL PANEL 6820EVS B.STROBES WILL REMAIN ACTIVE I S.T.C.STAPLED CEILING TILE �,SCD 3. WHEN THE F.A.C.P. IS RESET, THE FOLLOWING WILL N.T.S. NOT TO SCALE FAA 1 REMOTE ANNUNCIATOR 5860 OCCUR MECHANICAL A.INITIATING DEVICES WILL RESET NON PLENUM CEILING s FIRE ALARM CELLULAR E B.STROBES WILL STOP FLASHING AND RESET FAc 1 COMMUNICATOR SLE-LTE-FIRE C.FANS WILL RESET CL. F 4. TROUBLE AND SUPERVISORY SIGNALS WILL SOUND A �/� 8'-0"C.T. S TONE AT THE F.A.C.P. ONLY. NOT AN ALARM. THE RAWN QO. AM 1 SPEAKER AMPLIFIER ECS-125W F.A.C.P. WILL TRANSMIT A SIGNAL TO THE CENTRAL DN BASEMENT STATION ALSO BY: FIRE ALARM 8'-0"C.T. STORAGE ❑F 4 PULL STATION SK-PULL-SA 5. CARBON MONOXIDE DETECTORS SHALL SOUND A DRAFTING OIL TANK TEMPORAL 4 SEQUENCE AT DEVICE AND A TONE AT THE M.7ECr,SECUR/1Y3MEW BREAK RM ADWSIONOFnuR F.A.C.P. AND ANNUNCIATOR. F.A.C.P. WILL TRANSMIT 471 TOWNLINE ROAD (8'-0"C.T.) OFFICE ]5op (8'-0°C.T.) ® o OIL TANK �s 16 SMOKE DETECTOR SK-PHOTO-W A CO ALARM SIGNAL TO CENTRAL STATION. HVAC AND HAUPPAUGE, NEW YORK 11788 FANS SHALL SHUTDOWN. F PHONE: (631)-979-4500 UP 2 HEAT DETECTOR SK-HEAT-W DRAFTING(DaALARM-TECH.COM TOI LET 0. 4 CARBON MONOXIDE DETECTOR C01224TR/ o FIRE MARSHAL STAMPB OX APPLICANT: SO SK-M I N I MON �o� LIGHTHOUSE CL. >5° � god SECURITY INC. 14 CEILING SPEAKER STROBE SPSCRL �� 1149 OLD COUNTRY ROAD SUITE MEETING ROOM D-5,RIVERHEAD,NY 11901 APPROVED AS NOTED PHONE:(631)-727-2728 5C� 2 WALL MOUNT SPEAKER STROBE SPSRL V PHONE: SO CL. DATE 7 B.P.# N.Y.S.LICENSE#12000022174 SCD O� X� 1 OUTDOOR STROBE LIGHT SRK FEE BY; NOTIFY FIRE MARSHAL AT 631-765-1E02 SEAL: 5 CE'LING STROBE LIGHT SCRL FOR THE FOLLOWING INSPECTIONS: ��RE qRc `_'15CD � R 1. ROUGH INSPECTION SECOND FLOOR FIFE ALARM PLAN BASEMENT FIRE ALARM PLAN 1580 1 WALL STROBE LIGHT SRL �� 3. FIONALINS ECTIONING °r ,2. CLIANCE �a �,z� 5 ALL :- : CODES AND APPLICABLE NFPA SCALE: 1/8"=1' SCALE: 1/8"-1' WORK SHALL COMPLY WITH NYS N STANDARDS '9 2.,,9a�, Q- RISER DIAGRAM N ALL'COS 37UOT174 SWIG MEET THE REQUIREMENTS OF THE ° 75CD 75CD 15CD CODES OF NEW YORK STATE. H S S F S S PROJECT NAME: F P P USPENDED CEILING TILE SECOND FLOOR FIDE INSPECTIC'S PECONTC COMMUNITY REQU�IAR^ED E:FORE SCHOOL SECOND FLOOR OFFICES(TYPICAL} WP OPENING 75CD 27835 MAIN ROAD, 0 0 15CD 15CD 15cD S CUTCHOGUE, NY 11935 TAPLED CEILING TILE TAPLED CEILING TILE APLED CEILING TILE TAPLED CEILING TILE S S S c TAPLED CEILING TILE \STAPLED CEILING TIL TAPLED CEILING TILE P P P 75CD 75CD 75CD 75CD HALL WAY TYPICAL TOILET 1 ' CLASS ROOM 11' CLASS ROOM 11' CLASS ROOM 11' CLASS ROOM HALL WAY TYPICAL S S S S S C S C S C S C 9'-T (TYPICAL) 9'-T 9'-7' P P P P 75CD 75CD 75CD 75CD SCALE: 1/8" =11 Off S S F F AMP S S c S c S c DRAWN BY: GM P P JOB: PECONIC COM. SCHOOL 75CD 75CD 75CD 75CD SHEET: USPENDED CEILING TILE FAA FACP FAC S C S C S C S C BASEMENT STORAGE 120 VAC GROUND FLOOR 75CD rp "S,ZP H 15CD 15CD FA - I O S FIRE ALARM BUILDING ELEVATION DETAILS S P F BASEMENT FLOOR PLAN SCALE: 1/8"=1' 27 o 11 1 tICD CL CLASS ROC (11'-0"STC TO OFFICE Q C L. F PAAI � /� HALLWAY S�ISI��G (9'-6"STC) r.. - C L. OFFICE - --90 s CLASS ROC (11'-0"STC C L. /�}\ C, S C � 111 TOILET i � I I k'�IIARTITION WALLS NOTTOCEILING TOILET I i II FIRST FLOOR FIRE ALARM PLAN SCALE: 1/8"=1' LIBRARY TOILET Honeywell IntelliKnight 6820-EVS Battery Calculation .OMNr GHr Secondary Power Source Requirements Standby Device1.Control Panel 6820 Control Panel 1 1 1XI 0.190000 1=1 0.190000 1 1 IxI 0.250000 1=1 0.250000 2.Addressable SLC Devices a SK-PHOTO -T x 0.000300 = x 0.000300 = SK-PHOTO-W -T) 16 x 0.000200 = 0.003200 16 x 0.000450 = . 0.007200 SK-HEAT-HT -ROR x 0.000300 = x 0.000300 = SK-HEAT-W HT ROR 2 x 0.000200 = 0.000400 2 x 0.000450 = 0.000900 SK-BEAM x 0.002000 = x 0.002000 = SK-BEAM-T x 0.002000 = x 0.002000 = , SK-DUCT x 0.000300 = x 0.000300 = SK-ACCLIMATE x 0.000300 = x 0.000300 = SK-CONTROL x 0.000375 = x 0.000375 = SK-MONITOR x 0.000375 = x 0.000375 = SK-MINIMON 4 x 0.000375 = 0.001500 4 x 0.000375 = 0.001500 SK-PULL-SA 4 x 0.000375 = 0.001500 4 x 0.000375 = 0.001500 SK-PULL-DA x 0.000375 = x 0.000375 = SK-MONITOR-2 x 0.000750 = x 0.000750- _ SK-MON-10 x 0.003500 = x 0.003500 = SK-RELAY-6 x 0.001450 = x 0.001450 = 'SR-CONTROL-6 x 0.002250 = x 0.002250 SK-RELAY x 0.000255 - x 0.000255 = SK-RELAYMON-2 x 0.001300 = x 0.024000 = SK-ZONE x 0.000270 = x 0.000270 = SK-ZONE-6 x 0.002000 = x 0.002000 = SK-FIRE-CO x 0.000300 = x 0.007200 = 3.SLC Accessory.Bases B200S x 0.000300 = x 0.000300 - B200S-LF x 0.000300 = x 0.000300 = B200SR x 0.000300 = x 0.000300 = B200SR-LF x 0.000300 = x 0.000300 = B224RB x o.b00500 = x 0.000500 = RTS151 x 0.000000 = x 0.007500 = RTS151KEY x 0.000000 IxI, 0.007500 1=1 RA100Z x 1 0.000000 1 jil0.0100001=1. 4.SLC Isolator Devices SK-ISO x 1 0.000450 1=1 jxj0.000450 1=1 ISO-6 x 1 0.002700 1 IxI0.102000 1=1 13224131 x 1 0.000500 1 IxI0.000500 1=1 S.Auxiliary Power Draw-SLC Devices SK-CONTROL Aux.Power x 0.001700 = x 0.007000 = SK-CONTROL-6 Aux.Power) x 0.008000 = x 0.020000 = SK-ZONE Aux.Power x 0.012000 = x 0.090000 = SK-ZONE-6 Aux.Power x 0.050000 = x 0.270000 = B200S(Aux.Power) x 0.000500 = x 0.035000 = B20OS-LF(Aux.Power) x 0.000550 = x 0.140000 = B200SR Aux. Power x 0.000500 i IxI0.035000 = B200SR-LF(Aux.Power) I 1XI 0.001000 1=1 I jxj0.1250OQf 1=1 i18AY o ,DER ARc �5 e 14, 0 n P, 7. "91 0 3g46 0 NFN. Page 1 -- 12/28/2023 r 1 6.Accessory Modules 6815 x 0.078000 = xi 0.078550 = 5860 1 x 0.020000 = 0.020000 1 x 0.025000 = 0.025000 5824 x 0.045000 = x 0.045000 = 5496 x 0.010000 = x 0.010000 = 5895XL x 0.010000 = x 0.010000 = 6855 1XI 0.020000 = x 0.025000 = 6860 x 0.025000 = x 0.050000 = 5865-4 x 0.035000 = x 0.145000 = 5865-3 x 0.035000 = x 0.145000 = 5880 x 0.035000 = x 0.200000 = 5883 x 0.000000 = x 0.220000 = SK-IP-2 x 0.093000 = x 0.136000 = SK-IP-2UD x 0.098000 = x 0.155000 = CELL-MOD x 0.055000 = x 0.100000 = CELL-CAB-SK x 0.055000 = x 0.100000 = WSK-WGI Aux. Power x 0.040000 = x 0.040000 = SLC Power x 0.024000 = x 0.024000 = SK-NIC 1XI 0.0210010 = x 0.021000 = SK-NIC-KIT x 0.021000 = x 0.021000 = SK-FSL x 0.079000 = xj 0.079000 = SK-FML x 0.053000 = x 0.053000 = SK-FFT x 0.120000 = x 0.230000 = EVS-INT50W @25V x 0.052000 = x 0.275000 = EVS-INT50W WATTS USED @25V x 0.000000 = x 0.051300 = EVS-INT50W @70V x 0.052000 = x 0.310000 = EVS-INT50W WATTS USED @70V x 0.000000 = x 0.051800 = EVS-50W x 0.010000 = x 0.010000 = EVS-10OW x 0.010000 = x 0.010000 = EVC-100WBU x 0.010000 = x 0.010000 = EVS-125W 1 x 0.010000 = 0.010000 1 x 0.010000 = 0.010000 EVS-VCM x 0.070000 = x 0.100000 = EVS-SW24 x 0.010000 = x 0.025000 = EVS-LOC x 0.100000 = x 0.150000 = EVS-RCU x 0.090000 = x 0.125000 = SLE-LTE-FIRE 1 x 0.071000 = 0.071000 1 x 0.200000 = 0.200000 Miscellaneous Device 2 x 0.000000 = x 0.000000 = Miscellaneous Device 3 IXI 0.000000 = x 0.000000 = Miscellaneous Device 4 1XI 0.000000 1=1 ix, 0.000000 = 8.Output Circuits NAC 1 0.080000 = 0.080000 0.040000 = 0.040000 NAC 2 0.000000 = 1.712000 = 1.712000 NAC 3 0.000000 = 0.872000 = 0.872000 NAC 4 0.000000 = 0.000000 = 1/0 5 0.000000 = 0.000000 = 1/0 6 0.000000 = 0.000000 = Total Standby Load 0.377600 Total Alarm Load 3.120100 Page 2 12/28/2023 C Honeywell IntelliKnight 6820-EVS Battery Calculation SILENT* Note 1:You are fully responsible for verifying these calculations. ]MIGHT Note 2: Use the dropdowns in the yellow cells to enter values. Calculation in Total Sheet 24 Hours Standby Load Current 0.37760 Amps x 24 - 9.062 AH 5 Minutes Alarm Load Current(Amps) 3.12010 Am s x 0.084 = 0.262 AH - Total Current Load 9.324 AH Multiply by the Derating Factor 1.2 = x 1.20. Total Ampere Hours Required 11.19 AH Recommended Batteries: BAT-12120-12AH Batteries Battery Check The batteries can be charged by the 6820-EVS Charger. The batteries can be housed in the 6820-EVS Cabinet. Current Draw Check Circuit#1 current is within the limitations of the circuit. Circuit#2 current is within the limitations of the circuit. + Circuit#3 current is within the limitations of the circuit. Circuit#4 current is within the limitations of the circuit. Circuit#5 current is within the limitations of the circuit. Circuit#6 current is within the limitations of the circuit. 6820 Control Panel: The output current is within thepanel's limitations. Page 3 12/28/2023 Honeywell ®� IntelliKnight 6820-EVS Circuit Detail GHT NAC 1 ■• Draw Total Qty Alarm ■ CO1224TR 4 x 0.020000 = 0.080000 1 x 0.040000 = 0.040000 x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = Total Standby Load 0.080000 Total Alarm Load 0.040000 NAC 2 Device Qty Non-AlarmDraw TotaQty Alarm Draw Total SPSCRL STROBE @75CD 14 x 0.000000 = 0.000000 14 x 0.107000 = 1.498000 SPSRL STROBE @75CD 2 x 0.000000 = 0.000000 2 x 0.107000 = 0.214000 x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = X1 0.000000 =1 x 0.000000 = x 0.000000. = X1 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = Total Standby Load 1 0.000000 1 Total Alarm Load 1.712000 NAC 3 Device . Draw Total Qty Alarm Draw Total SRK @75CD 1 x 0.000000 = 0.000000 1 x 0.041000 = 0.041000 SCRL @15CD 5 x 0.000000 = 0.000000 5 x 0.158000 = 0.790000 SRL @15CD 1 x 0.000000 = 0.000000 1 x 0.041000 = 0.041000 x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = 1XI 0.000000 =I X1 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = Total Standby Load 0.000000 Total Alarm Load 0.872000 Page 4 12/28/2023 NAC 4 ■ Draw Total Qty Alarm Draw Total x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000• _ 1XI 0.000000 =1 X1 0.000000 = 1XI 0.000000 =1 x 0.000000 = 1XI 0.000000 =1 x 0.000000 = 1XI 0.000000 = x 0.000000 = I-XI 0.000000 = x 0.000000 = .} Total Standby Load 1 0.000000 Total Alarm Load 1 0.000000 1/O 5 Device Qty I Non-AlarmDraw TotalQty Alarm Draw Total x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = s; x 0.000000 = x 000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = 1XI 0.000000 =1 XI 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = Total Standb Load 0.000000 Total Alarm Load 0.000000 1/O 6 Device Qty Non-AlarmDraw TotalDraw Total x 0.000000 = x 0.000000 = , x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 x 0.000000 = x 0.000000 = x 0.000000 = XI 0.000000 = 1XI 0.000000 = x 0.000000 xi 0.000000 = x 0.000000 = x 0.000000 = x 0.000000 = X1 0.000000 = x 0.000000 = Total Standby Load 0.000000 Total Alarm Load 1 0.000000 Page 5 12/28/2023 Honeywell ®� IntelliKnight 6820-EVS EOL Voltage Drop Starting Voltage - 20.4 Volts Minimum Voltage 2 EOL 16 Volts Voltage Drop Warning% MOM : Current Actual Percent Draw Wire Type Resistance Len th Resistance [Voltage EOL Drop Feet(One Circuit Name Amps AWG Ohms/1000 ft. Way) Ohms Volts Percent NAC 1 0.080 #14 Solid 3.07 0: 0.00 20.40 0.00% NAC 2 1.712 #12 Solid 1.93 0 0.00 20.40 0.00% NAC 3 0.872 #12 Solid 1.93 0. 0.00 20.40 0.00% NAC 4 0.000 #12 Solid 1.93 --0 0.00 20.40 0.00% I/O 5 0.000 #12 Solid 1.93 0 0.00 1 20.40 0.00% I/O 6 1 0.000 1#12 Solid 1.93 -0" - 0.00 20.40 0.00% Resistance Table Wire Type Resitance AWG Ohms/1000 ft. #10 Solid 1.21 #10 Stranded 1.24 #12 Solid 1.93 #12 Stranded 1.98 #14 Solid 3.07 #14 Stranded 3.14 #16 Solid 4.89 #16 Stranded 4.99 #18 Solid 7.77 #18 Stranded 7.95 Note:All Resistance values are taken from Table 8 Conductor Properties of the NFPA 70 National Electrical Code.All values are for Direct Current Resistance at 75°C (167°F). f ;Lq Page 6 12/28/2023 Global Project Va u : SILENT Project Name:IPECONIC COMMUNITY SCHOO Standby Hours: 24 Project ID: Alarm Mins:L3 15 Prepared By:F Derating F 1.2 EVS-125W Calculations Date: 12/20/2023 Panel ID: EVS-125W Model: EVS-125W Audio Amplifier Location: Ckt.# Circuit Name Qty Current Draw Standby Alarm EVS-125W I EVS-125w Amplifier 25 Volts' 1 0.075 0.580 EVS-CE4 14 Zone Expander 0.000 0.000 Watts I Enter Number of Watts 4 N/A 0.160 Total Standby Current AMPS 0.075 0.740 Standby Time In Hours 24 0.250 Total Standbv AH Re uired 1.800 0.185 Total Combined AH Required 1.99 Multiply By The Derating Factor 1.20 ' Minimum Battery Am Hours Required 2.38 �Cq�j 121 • - = INN-P-Pppp- PHILADELPHIA COMMERCIAL 520 Shadow 1 825 Texas Bur 1169 Sand Dune +y 2027 Ohlone Oak 2028 Willow Oak .: V 2029 South Bay 5100 Blue Ridge i a i 6040 Honeycomb 7194 Mesa Oak I 7099 Aged Barrel Oak 7100 Seneca Oak 7192 Walnut Hill 7194 Mesa Oak 7195 Native Pecan --------- - hog • PHILADELPHIA COMMERCIAL Style Name Indwell 8 1W Style Number 566oV Construction Light Commercial Luxury Vinyl Tile Class/ASTM F1700 Class III Printed Film Vinyl Tile,Type B (embossed) Attached Underlayment No Finish ExoGuard° U.S. Metric Nominal Dimensions 7 in w,48 in 1 18 cm w,122 cm I Actual Dimensions 7 in w,48 in 1 17.78 cm w,121.92 cm I Wear Layer Thickness 8 mil(o.008 in) 0.2 mm Overall Thickness 0.079 in 2 mm Installation Direct Glue Recommended/ LokWorx+Resilient 7015M(49al)7005M (1 gal)or Required Adhesive S150 5125M Packaging Pieces per box 15 pcs Area per box 34.98 sq ft 3.25 sq m Weight per box 26.01 Ibs 11.8 kg Recommended Installation Method Itt tttt ttt t -� . t t Ashlar Brick Stagger Performance Testing Warranties 5 Year Commercial Limited Environmental Indoor Air Quality FloorScore®Certified Recycled Content Pre-consumer-0%, Post-consumer-0% Specifications are subject to nominal manufacturing variance. Material supply and/or manufacturing processes may necessitate changes without notice. SCSO� :•• .- . IMJ CONVEPSION MAINSTREET 13Y PHILADELPHIA �j 208 Rework 00 Reprise r, '1F b �� Z+....,E'.-.�.�'�'�,,�t'yx. �.k � •x-+^ 4 �c r�.°\. r - r� �� '�z.^'`� c � ��y1'�w�S' yC„ ...cy `' �'�.. ���*- ��`�°"-� � ' •-+� Gg M, gm 506 Replicate - - 'Y'- r �� kSa.'Fs�yt�'�-���--'#+-"-���;�,��..'t�6"�'n��i-•,r tics � �S�'��''��_W�� ��. � {{,� �'3�' v a„ ���a '�.�� �'.K�"-•r� �=��`3Tih'T�a't�`'§'c�..o:��U,$� r� � +c.� v._MEW- i MEN, R 4.o�'�11l'�.�ka.,� 510 Remake 700 Recast .i. 1 � CONVEPSION MAINSTREET 18Y PH I LADE.LPHI„ Style Name CONVERSIONNPIA Style Number 54974 Product Type Carpet Tile Construction Multi-Level Pattern Loop Fiber 100%Eco Solution Q®Nylon Dye Method Solution Dyed Primary Backing Synthetic Secondary Backing Strataworx Traffic Rating Heavy U.S. Metric Product Size 18 in x 36 in 45.72 cm x 91.44 cm Area Per Carton 63 ft2 5.85 m2 Pieces Per Carton 14 Gauge 1/10 in 3937 per 10 cm 1 ai. Stitches 10 per in 37 per 10 cm � Finished Pile Thickness 0.097 in 2.46 mm Average Density 5938 oz/yd3 Total Thickness 0.22 in 5.59 mm Tufted Weight 16 oz/yd2 542.5 g/m2 Recommended Installation Methods Monolithic Ashlar Brick Herringbone Basketweave Half Basketweave Boxed In Stagger Offset Performance Testing Pill Test Pass Radiant Panel Class I NBS Smoke Less than 450 Electrostatic Propensity Less than 3.5 kv CPI Greenlabel Plus GLP2671 ADA Compliance -0.6,meets the recommended static coefficient of friction for ADA walking surfaces and accessible routes Test Reports may be included or listed by the manufacturing/inventory style number as opposed to the noted selling style number. Warranties Carpet Tile 15 year Commercial Limited Warranty with Stain and Color for StrataWorx Environmental Recycled Content Pre-consumer-24%,Post-consumer-<7% patcraft , Socrates II 26 oz. PRODUCT SPECIFICATIONS COLLECTION Socrates I I { STYLE NUMBER 10068 t PRODUCT TYPE Broadloom 11 FIBER TYPE EcoSolution Q® Nylon DYE METHOD 100%Solution Dyed PRIMARY BACKING Synthetic SECONDARY BACKING Ultraloc® TRAFFIC RATING Heavy PROTECTIVE TREATMENTS R2X GSA APPROVED PRODUCT Yes US Units Metric Units PRODUCT SIZE 12 ft 3.66 m GAUGE 1/8 inches 31.50 per 10 cm STITCHES 7 per inches 28.87 per 10 cm FINISHED PILE THICKNESS 0.162 inches 4.11 mm AVERAGE DENSITY 5778 oz/yd3 0.21 g/Cm3 TOTALTHICKNESS 0.31 inches 7.87 mm TUFTED YARN WEIGHT 26 oz/yd2 881.55 g/m2 Performance Testing PI LL TEST Pass RADIANT PANEL Class I NBS SMOKE Less than 450 ELECTROSTATIC PROPENSITY Less than 3.5 kv CRI GREENLABEL PLUS GLP8472 ADA COMPLIANCE >0.6, meets the recommended static coefficient of friction for ADA walking surfaces and accessible routes Test Reports may be included or listed bythe manufacturing/inventory style number as opposed to the noted selling style number. Warranty Lifetime Commercial Limited Please visit patcraft.com for the most current warranty information. PATCRAFT.COM / @PATCRAFTFLOORS / 800.241.4014 ©2023 Shaw Industries Group,Inc.,a Berkshire Hathaway Company TRANSFORM patcraft, ' Socrates 1126 oz. Installation Methods Direct Glue,Stretch-In, Double-Stick Installation Guidelines Maintenance Guidelines Environmental Specifications RECYCLABILITY 100%recyclable Materials gngredoents DOES NOT CONTAIN does not contain PVC,phthalates or PBD/PBDE Recycled Content TOTAL RECYCLED CONTENT(BY WEIGHT) <1% PRE-CONSUMER <1% POST-CONSUMER 0% Meets or exceeds all local and national regulations in country of manufacture.Manufactured in an IS09001&IS014001 certified facility or equivalent Recycled content is calculated using system allocation,mass balance,and direct insertion.The actual recycled content in this product will likelyvary.For more information email info@patcraft.com. Third Party Certifications CRADLE TO CRADLE CERTIFIED® Silver Level (Version 3.1) HEALTH PRODUCT DECLARATION(HPD) Per GHS SDS Disclosure ENVIRONMENTAL PRODUCT 3rd Party Certified in Accordance with IS014044, IS014025& DECLARATI ON(EPD) EN15804 NSF 140 Gold CRI GREEN LABEL PLUS(GLP) GLP22T ENVIRONMENTAL GUARANTEE Pickup&Delivery Available in Americas PRODUCT PACKAGING 100%Recyclable USGBC LEED contributes Nwiff Specifications are subject to nominal manufacturing variances.Material supply and/or manufacturing processes may necessitate specification changes without notice.This carpet is an exclusive design and may not be duplicated in any manner.Use of this design in the creation of another carpet design is also strictly prohibited.Visit patcraft.com/testing for more information. PATCRAFT.COM / @PATCRAFTFLOORS / 800.241.4014 . . . . ©2023 Shaw Industries Group,Inc,a Berkshire Hathaway Company C01224A '^ SYSTEM SENSOR® - - --- !0 CO 1224 Series Carbon Monoxide Detectors with Rea1Test° C : •_�• Technology - C01224T The System Sensor CO1224T, CO 1224TR, and CO1224A �►. .,; , (Canada)Carbon Monoxide(CO)Detectors use a highly P. accurate and reliable electrochemical sensing cell to - C01224TR provide early warning of dangerous CO levels. Features When dangerous amounts of CO are detected,the C01224 A 10-year end-of-life timer Series CO detectors alert residents by sounding and flashing a temp 4 signal alarm.With 24/7 central station monitoring,residents are a RealTest®enables a functional test using canned CO guaranteed protection whether they are away from home,sleeping, A code-required trouble relay or already suffering from the effects of CO. Wiring supervision with SEMS terminals The C01224 Series detectors are designed for system operation. a 12/24 VDC These detectors are fully listed to UL 2075(US models only)and a A low current draw of 20 mA in standby and 40 mA in alarm CSA 6.19-01 (Canada model only)and offer a code-required trouble • Versatile mounting for wall and ceiling relay to send a sensor failure or end-of-life signal to the control panel and the central station.The C01224 Series detectors also Accurate and reliable electrochemical sensing technology use SEMS-type terminal Philips head screws for quicker and more a Optional CO-PLATE CO Detector Replacement Plate to upgrade positive wiring connections and code-required wiring supervision. previously installed competitor detectors to the C01224T or With a low current draw,these detectors enable more devices to be CO1224A. connected to the panel,limiting the need to purchase extra power ' C01224T tested up to 12,000 feet above sea level supplies or more expensive panels.As 12/24 VDC detectors,the CO1224 Series detectors will operate on most industry security and fire alarm control panels. With RealTest®technology,the CO gas sensing cell used in the C01224 Series CO detectors can be tested using a CO gas agent, fully meeting the requirements of NFPA 720:2009(US models only). Simply put the detector into RealTest mode,spray a small amount of CO into the detector per the installation instructions,and within seconds the detector will alarm,indicating successful gas entry.(See the reverse page or the user manual for complete instructions.) Agency Listings U <. Note:CO1224T& C01224TR are in full compliance with UL LISTED L 2075 and C01224A is in full compliance with E307195 E304075 ULC CSA 6.19-01. C01224 Series Detectors Carbon Monoxide Detector Specifications Architectural/Engineering Specifications Carbon monoxide(CO)detector shall be a system-connected System Sensor model number C01224T or C01224TR listed to Underwriters Laboratories UL 2075 for Gas and Vapor Detectors and Sensors.The Canadian model C01224A,is ULC listed to CSA 6.19-01,for residential carbon monoxide alarm devices.The detector shall be equipped with a sounder and a trouble relay.The detector's base shall be able to mount to a single-gang electrical box or direct(surface)mount to the wall or ceiling.Wiring connections shall be made by means of SEMS screws.The detector shall provide dual-color LED indication that blinks to indicate normal standby,alarm,or end-of-life.When the sensor supervision is in a trouble condition,the detector shall send a trouble signal to the panel.When the detector gives a trouble or end-of-life signal,the detector shall be replaced.The detector shall provide a means to test CO gas entry into the CO sensing cell.The detector shall provide this with a test mode that accepts CO gas from a test agent and alarms immediately upon sensing CO entry.For the C01224T only, the detector shall perform in the detection of CO up to 12,000 feet above sea level and alarm within the time specified by ANSI/UL 2034 for CO concentrations of 70, 150 and 400 parts per million(ppm),as verified by a Nationally Recognized Test Laboratory. Electrical Specifications Operating Voltage 12/24 VDC Audible Signal 85 dB in alarm Standby Current 20 mA Alarm Current 40 mA(75 mA test) Alarm Contact Ratings 0.5 A @ 30 VDC Trouble Contact Ratings 0.5 A Cad 30 VDC Physical Specifications Size:C01224T&C01224A Length:5.1 in(130 mm),Width: 3.3 in(84 mm),Height:1.3 in(33 mm) Size:C01224TR Diameter:6.0 in(152 mm),Height:1.3 in(33 mm) Approximate Weight C01224T&CO1224A:7 oz(198 g);CO1224TR:11 oz(312 g) Operating Temperature Range 32°F to 1040 F(O°C to 400 C) Operating Humidity Range 22 to 90%RH Input Terminals 14 to 22 AWG Mounting Single-gang back box;surface mount to wall or ceiling Operation Modes Operation Mode Green LED Red LED Sounder Normal(standby) Blink 1 per minute — — Alarm — Blink in temp 4 pattern Sound in temp 4 pattern RealTest®Feature: The System Sensor C01224 Series CO Detectors enable evaluation of the functionality of the CO sensing cell using a canned CO test agent. NOTE:Check with local codes and the AHJ to determine i ---- if a functional gas -- test is desired for an / ? ) installation. Push and hold the Test/Hush button for Spray canned CO agent into the Verify CO sensing at the control panel. two seconds to enter RealTest mode.The detector. The detector will automatically exit green LED will flash once every second to RealTest alarm mode after about 20-60 indicate RealTest mode has started. seconds. Hush Feature: Pushing the Test/Hush button will silence the sounder for 5 minutes(except in RealTest mode). Trouble Feature: When the detector is in a trouble condition,it will send a trouble signal to the panel.End-of-Life Timer: After the detector's internal sensor has reached the end of its life,a trouble signal will be sent to the panel to indicate it is time to replace the detector.An electrochemical CO detector lifespan is about ten years. El The detector must be replaced by the date marked on the inside of the product. CO-PLATE: System Sensor also offers the CO-PLATE CO Detector Replacement Plate to cover the footprint(when necessary) of previously installed competitive carbon monoxide detectors that require replacement. INJ Ordering Information CO-PLATE Part No. Description C01224T 12/24 volt,6-wire system-monitored carbon monoxide detector with RealTest®Technology(US only) C012 4TR 12/24 volt,6-wire system-monitored round carbon monoxide detector with RealTest®Technology(US only) C01224A 12/24 volt,6-wire system-monitored carbon monoxide detector with RealTest®Technology(Canada only) CO-PLATE CO detector replacement plate to cover the footprint of previously installed competitive detectors(US&Canada) SYSTEM US:3825 Ohio Avenue Canada:6581 Kitimat Rd,Unit 6 ©2016 System Sensor.Product specifications subject to St.Charles,IL 60174 Mississauga,Ontario 1_5N 3T6 change without notice.Visit our websites for current product ® 800-SENSOR2 BOO-SENSOR2 Information,including the latest version of this data sheet. SE/1/SOR systemsensor.com systemsensor.ca CODS88600.10/16 UNIQUE ID NUMBER State of New York FOR OFFICE USE O N L Y I2000022174 Department of�State Control DIVISION OF LICENSING SERVICES No. �, � PURSUANT TO THE ROvIS Or45 OF ARTICLE S7 OF 'T�H EFFECTIVE DATE i MO. DAY I YR. GENERAL BUSINESS LAW AS IT RELATES TO THE BUSINESS II �)4 12 OF INSTALLING, SERs.P.ICING, OR MAINI'TA.�:��ING' 'SF-Ct FfjTy I OR FIRE ALARM SYSTEMS. `1 EXPIRATION DATE LIGHTHOUSE SECUR r-' INC MO. I DAY I Y . 1149 OLD COUNTRY r' STE D-5 RIVERHEAL, NY 2 G HAS BEE14 DULY LICENSED TO ENGAGE IN THE BUSINE& OF I1ISTALLIlVG, SERVICING, OR MAINTAINING SECURITY OR FIRE ALARM SYSTEMS F; In Witness Whereof,The Department of State has caused its off cial seat to to hereunto affixed. GUAL I F I ER: SAN TACROC E TH MAS E JR R Csf:;E^ J. F,0DR I G_3E r SECRET"AFt Y I;UOS-1098(Rev,3/01) Or STAT T ;L— 4 Z 6820EVS Intelligent Fire Alarm Control Panel with Emergency Voice System The 6820EVS panels and accessories provide features to meet the requirements for Mass Notification Systems as described in UL 2572 2nd Edition and UL 86410th Edition. The 6820EVS is an intelligent addressable Fire Alarm Control Panel combined with an Emergency Voice System(EVS)and are direct replacements for the 5820XL-EVS FACP. When the EVS features are enabled,they are integrated with the fire alarm and voice evacuation functions of the control panel. The emergencyvoice system operations include an onboard supervised microphone.All-call and non-active call buttons can quickly select all active or non-active output groups.The system also allows for emergency messages over fire. The 6820EVS FACP has one built-in signaling line circuit(SLC),which can support 159 SK detectors and 159 SK modules,or 127 SD protocol devices.Additional SLC loops can be added for a maximum of 1110(SK)or 635(SD)points per panel. The built-in digital alarm communicator/transmitter(DACT)is dual technology,IP and POTS.The POTS transmits system status(alarms,troubles,AC loss,etc.)to a Central Station via the public switched telephone network.The IP communicator's internet monitoring capability sends alarm signals over the Internet saving the monthly cost of two dedicated business telephone tines.Although not required,the secondary telephone line may be retained providing backup communication overthe public switched telephone line.Optional cellular reporting is available. The 6820EVS has six onboard Flexput°circuits that can be configured as notification outputs or auxiliary power.The 6820EVS also has a form-C trouble relay,and two programmable form-C relays,along with powerful features such as drift compensation,pre- trouble maintenance alert,a built-in sensor testto complywith NFPA 72 calibration testing requirements,and a calibration trouble alert. A common communications and annunciation link allows up to 17 panels to be connected via copper or fiber optic cable.A designated panel is configured as the communicator for all panels in the link for convenient single-point communications. FEATURES AND BENEFITS • Single enclosure for both fire and • Selectable strobe synchronization for • Two programmable relays and one fixed emergency voice components Amseco°,System Sensor',Wheelock',and trouble relay • Ability to select EVS messages as priority Gentex°devices • Compatible with SWIFT°wireless devices over fire • Built-in DACTwith IP and optional cellular • Convenient field-upgradeable firmware • 15 Recordable one-minute messages that reporting • Network support for up to 17 sites can be mapped to eight EVS buttons • Built-in USB interface for quick and easy • Network card allows copper network • Capable of producing 520 Hztones to meet programming connection with a multi-mode or single- NFPA 72 requirements • JumpStart°auto programming reduces mode fiber connection • Support for up to 4 LOC consoles and 8 installation time • Real-time clock/calendar with automatic addressable amplifiers • 999 software zones&999 output groups daylight savings control • Expandable SLC loops to 1110(SK)or 635 for flexible design options • History file with 1,000 event capacity (SD)point capacity • 23 preset notification cadence patterns • Six Flexput circuits for NAC outputs or (including ANSI°3.41) auxiliary power • Allows up to 24 SBUS devices • Four programmable function keys Honeywell SILENT' MGHT USER INTERFACE SK COMPATIBLE ADDRESSABLE DEVICES LED INDICATORS Note:SKand SD devices cannot be mixed in the same fire alarm • GeneralAlarm(Red) system. • Supervisory(Yellow) SK-ACCLIMATE:Multi criteria photoelectric smoke detector with thermal 1�51F fixed temperature • System Trouble(Yellow) • System Silenced(Yellow SK-BEAM:Reflected beam smoke detector without test feature • System Power(Green) SK-BEAM-T:Reflected beam smoke detector with test feature KEYPAD OSI-RI-SK:Reflected beam smoke detector,SK protocol • 12-key numeric pad SK-CONTROL:Supervised control module • Acknowledge SK-CONTROL-6:Six circuit supervised control module • Alarm Silence SK-DUCT:Photoelectric duct smoke detector with extended air • System Reset speed range • Drill SK-FIRE-CO:Four criteria fire and carbon monoxide detector • Fl-F4 Programmable Function Keys SK-FIRE-CO-W:Four criteria fire and carbon monoxide detector, white PROGRAMMING SK-HEAT:Fixed thermal detector(135°F) The 6820EVS system offers several options to simplify and expedite SK-H EAT-W:Fixed thermal detector(1351F),white programming.JumpStart°auto programming minimizes SK-HEAT-ROR:Fixed rate of rise detector programming required to start a new system.The built-in keypad,or the remote annunciators give on-site access to current system SK-HEAT-HT:Fixed high temperature heat detector(190°F) programming.System programming can also be accomplished SK-HEAT-HT-W:Fixed high temperature heat detector(190°F), using the Windows°-based Honeywell Fire Software Suite(HFSS). white ORDERING INFORMATION SK-HEAT-ROR-W:Fixed rate of rise detector,white 6820EVS:Addressable fire alarm control panelwith emergency SK-ISO:Fault isolator module voice system,red SK-MINIMON:Mini monitor module COMPATIBLE EVS EQUIPMENT SK-MONITOR:Monitor module EVS-50W:50 Watt amplifier SK-MONITOR-2:Dual input monitor module EVS-125W:125 Watt amplifier SK-MON-10:10-input monitor module EVS-10OW:50/100 Watt amplifier SK-PHOTO:Photoelectric smoke detector EVS-10OWBU:External backup amplifier SK-PHOTO-W:Photoelectric smoke detector,white EVS-INT50W:50/Watt internal amplifier SK-PHOTO-R:Photoelectric detector with remote test capability EVS-CE4:Provides 4 additional audio circuits SK-PHOTO-R-W:Photoelectric detectorwith remote test capability, EVS-RVM:Remote voice module white EVS-SW24:24 switch expander SK-PHOTO-T:Photoelectric smoke detector with fixed heat(135°F) EVS-VCM:Network voice control module SK-PHOTO-T-W:Photoelectric smoke detectorwith fixed thermal heat(13519,white EVS-LOC:Local operator console SK-PTIR-W:Multi criteria photoelectric smoke detectorwith thermal COMPATIBLE SBUS DEVICES 1350F fixed temperature,white 6860:4x40 LCD remote fire annunciator with four programmable SK-PULL-SA Addressable single action pull station buttons,red SK-PULL-DA:Addressable dual action pull station 5860:4x20 LCD remote fire annunciator,gray SK-RELAY:Addressable relay module 5860R:4x20 LCD remote fire annunciator,red SK-RELAY-6:Addressable Six relay control module 6855:420 LCD remote fire annunciator,red SK-RELAYMON-2:Addressable Dual relay/monitor module 5865-3:LED annunciators-display up to 30 LEDs(15 red/15 SK-ZONE:Addressable zone interface module yellow) SK-ZONE-6:Six zone interface module 5865-4:LED annunciators-display up to 30 LEDs(15 red/15 yellow).Keyswitches for silence and reset,and a system trouble LED 5880:LED 1/0 module with 40 programmable LED outputs and eight supervised dry contact inputs 5883:Relay interface.Provides 10 Form C relays 58244:Serial/Parallel printer interface module for printer connection Page 2 of 4—351606:E•3/7/2022 SK BASES SYSTEM EXPANDERS B210LP:6"mounting base 6815:SLC Expanderfor IDP orSK devices B501:4°Flangeless mounting base 5815XL:SLC expander for SD devices B200S:Intelligent sounder base RPS-1000:6A power supply with 6 Flexput circuits&2 Form C B200S-LF:Low-frequency intelligent sounder base relays B224RB:Relay base 5496:6 amp NAC power expander with 4 power-limited output ckts 1322413I:Isolator base OPTIONAL COMMUNICATORS SO COMPATIBLE ADDRESSABLE DEVICES CELL-CAB-SK:Cellular communicator,metal enclosure w/lock& Note:SK and SO devices cannot be mixed in the same fire alarm key system. CELL-MOD:Cellular communicator,plastic enclosure IPGSM-4G:Dual path fire alarm communicator,cellular and/or IP SD505-6AB:Addressable 6"base (primary or backup,selectable) SD505-6113:Addressable 6"short circuit isolator base SK-I13-2:Remote reporting via the Internet.Requires a VisorALARM° SD505-6RB:Addressable 6"relay base receiver at the central station SD505-6SB:Addressable 6"sounder base MISCELLANEOUS ACCESSORIES SD500-AIM:Addressable input module(switch input) SK-NIC:Network Interface Card.Provides a common SD500-ANM:Addressable notification module communications link for the IFP-300 SD500-ARM:Addressable relay module SK-NIC-KIT:Installation Accessory Kit SD505-DTS-K:Remote test switch/LED indicator for the SK-FML:Fiber-Optic Multi Mode,transmitter and receiver SD505-DUCTR SK-FSL:Fiber-Optic Single Mode SD505-DUCT:Addressable Duct Smoke Detector RBB:Remote battery box accessory cabinet SD505-DUCTR:Addressable Duct Detector housing with relay base SK-SCK:Seismic compliance kit used to fasten batteries to the fire SD505-HEAT:Absolute temperature heat detector.Trip point range panel from 1351F-1501F(0°C-3710 SOFTWARE SOLUTIONS SD500-LIM:Addressable Line isolator module SKST:Silent Knight Selection Tool provides the installer or design SD500-MIM:Addressable Mini input monitor module(switch input) architectwith a Windows°-based software system configuration tool to create a detailed bill of material(BOM)and battery SD505-PHOTO:Photoelectric smoke detector calculations SD500-PS/-PSDA:Addressable Single or dual action pull station HFSS:Honeywell Fire Software Suite provides remote and local SD500-SDM:Addressable smoke detector module panel programming,detector status,event history and additional SWIFT WIRELESS DEVICES data.Databases can be uploaded/downloaded via the panel's USB port using a flash drive.Requires a PC running Microsoft' Note:SWIFT is only compatible with System Sensor(SK)devices.It Windows'. is not compatible with Hochiki(SD)devices. WSK-WGI:Wireless gateway WSK-PHOTO:Wireless photoelectric smoke detector with B501W base WSK-PHOTO-T:Wireless photoelectric smoke detector with fixed thermal detection(135°F)and B501W base W-SYNC:Wireless sync module WSK-HEAT:Wireless,fixed heat detector(135°F)with B501W base WSK-HEAT-ROR:Wireless rate-of-rise heat detector and B501W base WSK-MONITOR:Wireless monitor module WSK-RELAY:Wireless relay module WSK-PULL-DA:Wireless pull station WAV-RL,WAV-WL,WAV-CRL,WAV-CWL:Wireless AV bases W-USB:Wireless USB radio/antenna dongle that plugs into the USB port ofa PC running SWIFT Tools SWIFTTools:Programming and diagnostic utility forthe,wireless gateway and devices.Available for download from www.farenhyt.com 351606:E•3/7/2022 — Page 3 of 4 _0 4 6820EVS TECHNICAL SPECIFICATIONS SYSTEM CAPACITY TEMPERATURE AND HUMIDITY Intelligent Signaling Line Circuits:1 RANGES ' ' • (expandable) This system meets NFPA requirements for Silent KnightO, Addressable device capacity:1110(SK)or operation at 0—49°C(32-120°F)and at a • trademarks 635(SD) relative humidity 93%±2%RH(non- of • - International condensing)at 32°C±2°C(90°F±3°F). A . -. Programmable software zones:999 However,the useful life of the system's of Potter Electric Signal Company, Output circuits:6(expandable) standby batteries and the electronic LLC - W is a registered SBUS devices:24(16 annunciators,8 LED components may be adversely affected by modules) extreme temperature ranges and humidity. trademarkofGentexCorporation. Therefore,it is recommended that this Hochikil is , registered trademark LOC units:4 system and its peripherals be installed in an . . Corporation.Wheelock" Addressable amplifiers(total watts):8 environment with a normal room is a • Cooper F. (1000) temperature of 15—271 C/60—80° trademark Technologies Company.ANSI"is a ELECTRICAL STANDARDS AND CODES registered trademark AC Power:120VAC,60Hz,3.3A The 6820 complies with the following American Standby Current:190 mA standards and codes: Institute,Inc.VisorALARMO Alarm Current:250 mA NFPA 72 registered trademark o - .. NFPA13 Corporation. Microsoft" Flexput Circuits:Terminal block provides connections for(six Class B orthree ClassA) NFPA 15 •• registered NACs or auxiliary power.Power-limited, NFPA 16 trademarks of • ' ft supervised circuitry.Maximum current per NFPA 70 Corporation. circuit:3 A.Cannot exceed 6A total for all UL 864 10th Edition circuits.End-of-line resistor:4.7k ohm,'/z This document is not •' • be watt for Class B NACs UL2572 2nd Edition -• forinstallation purposes. Communication Loop:Supervised and Central station;remote Signaling;Local try to keep our product information power-limited,Class A or Class B,32VDC, Protective Signaling Systems;Auxiliary up-to-date • accurate.We cannot 150mA Protected Premises Unit;Water Deluge releasing service.Suitable for automatic, cover specific Two Programmable Relays and One Fixed manual,waterflow,sprinkler supervisory anticipate all requirements.All Trouble Relay:Contact rating:2.5 A C 27.4 (DACTnnn-coded)signaling services specifications •change VDC(resistive),Form C Battery:Cabinet holds maximum of two 18 AGENCY LISTINGS ANDwithoutnotice. AH batteries APPROVALS origin:Country of Battery Charger Capacity:7-35 AH UL Listed: S2766 PHYSICAL CSFM:7165-0559:0500 Dimensions:21.6"W x 28.1"H x 5.1"D FDNY: COA#6249 (54.9cm W x 71.4cm H x 13.Ocm D) FM:Approved Weight:50 lbs.(22.7 kg.) Seismic:(CA)VMA-45894-05C: Color:Red Honeywell Silent Knight 12 Clintonville Road Northford,CT 06472-1610 Honeywell 203.484.7161 351606 1 E 1 04/22 SILENT- www.silentknight.com ©2022 Honeywell International Inc. 13 KMGHT 5860/586OR Remote Annunciator The 5860/R operates and programs Silent Knight°fire alarm control panels (FACPs).The 5860/R's keypad and display match the built- in annunciator of the FACR o � J• The remote annunciator connects to the control panel via the RS-485 system bus.When the ® ' ' system is in normal operation and has AC power,the Power LED is lit and all other LEDs are ty " off.The other LEDs turn on as alarms,supervisories,troubles,system silenced,and AC power losses occur. INSTALLATION The 5860/R can be surface or flush mounted.Use the optional trim ring for surface mounts. When flush mounting,an electrical box is optional.If using an electrical box,use a 4S, single-gang,or double-gang box. COMPATIBILITY The 5860/R is compatible with the following Silent Knight FACPs: • 6820/6820EVS • 6808 • 6700 • 5820XL/5820XL-EVS • 5808 • 5700 FEATURES AND BENEFITS • UL listed.Complies with UL 864,10th • Initiate and end fire drills with a single key • Available in red or gray color Edition;UL 2572,2nd Edition;and NFPA 72 press • Accepts user codes or fire fighter's key • 80-character backlit LCD display(4 lines • View current status by alarms, • Support for simultaneous use of multiple with 20 characters on each line) supervisories,or troubles 5860/Rs • Tactile/audible feedback • On-board piezo sounder audibly indicates • Wiring lengths up to 6000 ft.(1.83 km)from • RS-485 SBUS interface to panel alarms,troubles,and supervisories the FACP • Larger keypad buttons for system reset and • Five status LEDs for;alarms,supervisory, silence trouble,silence and AC power indications Honeywell SILENT' KNIGHT 5860/586OR TECHNICAL SPECIFICATIONS PHYSICAL ORDERING INFORMATION Dimensions:9.1"W x 7.4"H x 1.5"D 5860R:Red four line LCD Remote Honeywell,"and Silent Knight,"are (23.1 cm W x 18.8 cm H x3.8 cm D) Annunciatorwith 20 characters per line. registeredtrademarks of • c ll Shipping Weight:2.8 lbs(1.3 kg) 5860:Gray four line LCD Remote International,Inc, Color:Red or Gray Annunciator with 20 characters per line. This document is not • •- ENVIRONMENTAL OPTIONAL ACCESSORIES .• purposes. 5860TR:Red Trim Ring for surface try to keep our product inf. • Operating Temperature:32°F to 120°F mounting. up-to-date and accurate. cannot (0°C to 49°C) 5860TG:Gray Trim Ring for surface cover all specificapplications Humidity:10%to 93%relative humidity mounting. anticipate (noncondensing) STANDARDS AND CODES specifications • "subjectto change ELECTRICAL The 5860/R complies with the following without notice. Operating Voltage:24 VDC standards/codes: Country of origin: U.S.A. Standby Current:20 mA • UL 864,loth Edition:Standard for Control Alarm Current:25 mA Units for Fire Alarm Systems Maximum Wiring Distance:6,000 ft.(1.83 • UL 2572,2nd Edition:Standard for Mass km)from FACP(depending on wire gauge Notification Systems and number of devices on the SBUS) • NFPA 72:National Fire Alarm and Signaling SYSTEM Code Maximum No.of 5860/Rs per System: AGENCY LISTINGS AND • 8 for 5700 or 6700 APPROVALS • 12 for 5808 or 6808 • UL Listed • 16 for 5820XL/EVS or 6820/EVS • FDNY-COA(TBD) Honeywell Silent Knight 12 Clintonville Road Northford,CT 06472-1610 Honeywell 203.484.7161 350224 1 1 111/21 ®SELFNT" www.sitentknight.com ©2021 Honeywell International Inc. KNIGHT tar' r1 'r"P, Commercial Fire Alarm Cellular &tor^IP .' COMMERCIAL.FIRE.CELCULAR,&IP, .' FIr&Aldrm LTE Co.mmun:icato:rs • Universal full event sole&dual path cellular&/or IP UL and NFPA 72 Fire Code-Compliant,the Starl-ink commercial fire alarm reporting from any panel brand, Series Wireless Commercial Fire Alarm Sole Path&Dual virtually anywhere Path Communicators provide universal support for any brand 12V to 24V fire alarm control panel,reporting in • Code-compliant,replaces 2POTs lines per FACP saves Contact ID and 4/2. With broadest Verizon LTE coverage thousands of dollars per year over the leased landlines footprint available,via most extensively deployed LTE CAT1, • Supports 12V-24 control panels and FACPs that using proven Starl-ink circuitry,they are also available communicate using Contact ID and 4/2(such as on legacy in mercantile locking metal models.All provide the most panels),as primary or backup economical solution for easy,versatile installation.Also regional compliances,i.e.,CSFM,NYCFD,LAFD and more. • Full data Reporting to any Central Station nationwide, via Verizon®LTE Network,'The Nations largest and most Easy,Universal Installation at Every Application;Panel- reliable LTE network.Rated#1 overall network,proven to Powered Technologr.StarLink Fire Communications are deliver consistently fast speeds ad i more places than any easily connected to any panel or Fire Alarm Control Panel other network"# (FACP)standardly operating between 12V and 24V.Flexible in any application,Starl-ink Fire also comes in standard,or • Communicate critical life and safety alarm reports on Mercantile Models in metal housings,with code-compliant LTE(Long Term Evolution)10+year life,cyber-protected supervision,and choice of power options,Panel-Powered multi-billion dollar cellular network,for maximum life Technology'(powered by the panel),or direct-connect safety&liability protection 120VAC models.Signal Boost circuitry&dual diversity antennae for maximum signal acquisition&null avoidance, • Easiest installation,powered by panel, NO extra power receiving signals simultaneously on both antennae. supply,NO conduit,self supervised on 4 wires Flexible Performance&Reporting Options.Starl-ink • Over-the-Air Upgradeable Communicator Firmware. Fire provides full data reporting,in sole and dual path,as Remote ability for critical/mandatory updates,without a a primary or backup,to any central station of your choice, truck-roll without requiring any special equipment on premises. • Ultra-affordable plans are available to meet various codes Cost-saving models and plans for any code requirement. and requirements,with supervisory check-ins from 200 Substantial savings over monthly dedicated landline charges. seconds,to 5 minutes,to an hour.The units are very easily And,$100 saving incentive for system upgrades from old activated,plans and options are selected,and 24%7 account radios(all makes)and old POTS landlines,as well as new management is provided all through www.napcocomnet.com. installations connected by Napco StarLink Universal Fire Alarm '. verizorn/ Communicators • Sole Path Cellular and Dual Path Cellular&/or IP Models • Choice of plans(varies by model)-check-ins from 200 seconds,to 5-minutes to 1 hour,Verizon LTE Network Patented Signal Boostrm andDual Diversity Antennae M. for maximum signal acquisition&null avoidance, receiving signals simultaneously on both antennae • Money-saving Tradeup incentive credit • Bonus:Full High-Speed Napco Panel remote uploading/downloading • COMPLIANCES:NFPA72 Editions:2016,2013,2010, 2007;UL 864,9th Ed.,UL1610,UL985,UL1023,NYCFD; CSFM;LAFD Star�ilnkMOO NFPA Code-compliant standard or mercantile metal models(right and left respectively), ar nk'Foire'. Commercial Fire Alarm Cellular &[or IP COMMERCIAL FIRE CELLULAR&IP Flre Alarl'1'1 ;LTE..COmmUnlCatOrS . StarLink Fire Specifications Ordering Information STANDARD MODELS: COMMERCIAL FIRE SOLE PATH CELLULAR& • Advanced LTE Dual Diversity Antennae for optimized DUAL PATH CELLULAR&/OR IP("I"MODELS):* performance SLE-LTEVI-FIRE Dual Path Communicator,Cellular&/or IP, • Durable ABS plastic housing includes three keyhole slots for connected by Verizon LTE',ABS.Low current draw,panel- mounting(for commercial application,aligns with triple gang powered technology'(powered by control panel) boxes) SLE-LTEV-FIRE as above,but sole path cellular model • Panel Powered Technology"(powered by panel),Low current SLELTEVI-CFB Commercial Fire Dual Path Mercantile model draw,71 mA standby,200mA transmit in red metal housing on LTE,Verizon LTE Network,powered • Dimensions:5-3/8"x 7-7/8"x 1-7/8"(HxWxD) directly from control panel • Weight:13.5 oz SLETEVI-CFB-PS Commercial Fire Dual Path Mercantile model • 3 LED Indicators-Green,Signal Strength;Amber-Busy/ in red metal housing,LTE,Verizon LTE Network.Direct 120VAC Activation;Red-Trouble Powered(w/provisions for backup battery/charger).Or, • Patented Signal BoostN signal amplification circuit and high- Optional TRF12 plug-in transformer may be used,where codes gain performance antennae permit • Operating Environment:0 to 490 C(32-1200F),up to 93% ACCESSORIES: humidity(non-condensing) Free Commercial Fire Tradeup Trifold • 12V-24V Universal FACP Support,auto-current sensing. Brochures/Mailers/Stuffers(A720)for new v , Support all brands communicating in Contact ID and 4/2 and existing fire accounts SLE-ANTEXT75 Optional extended antenna with, MERCANTILE MODELS(similar to above,with): 75'cable(new conical shape) try 4 a'' • LockingMetal Enclosure with Hinged door& 2 key-slots for g Y SLE-ANTEXT50 As above,with 50'cable wall mounting(LED indicators,inside) SLE-ANTEXT30 As above,with 30'cable • Dimensions: 9-5/8"x 11-3/4"x 3-3/8"D(HxWxD) SLE-DLEXT Optional,as above,for downloading,extends distance • Weight:8 Ibs(max.,power supply models) to Napco panel up to 100' • Electrical Ratings for 120VAC,60Hz TRF12 Optional Plug in AC Transformer,16.5V/20VA(use is • For Models with Power Supply: subject to local code compliance) • Input Voltage: 120VAC Nominal SLE-DLCBL Optional High-Speed Napco Panel Up/download cable • Input Current:400mA maximum • Maximum Charging Current: 200mA _ • Electrical Ratingsfor+12V New! FireLink'' Integrated-Fire Alarm'Control,- • For Models without Power supply: Panel w/StarL'Ink Fire LTE"Built In' ' • Input Voltage: 11-15VDC(power-limited output from listed _- Award winning FL-FACP-revs control panel) FSX Firewolf 8 Zone 24V Conventional- or"s`�. Commercial Fire Alarm Control • Input Current:71 mA with peak RF transmission current of Panel with onboard StarUnk Fire® 200mA Sole Path,Verizon LTECellular • Electrical Ratings for the IN 1 Burg/Fire Input: Alarm communicator and integral menu-driven LCD annunciator,w/ • Input Voltage:9-15VDC 4amp,24V power supply.Optionally 'expandable• Maximum Input Current:U to 2mA from FACP NAC circuit commercial addressable, cb ss points/zones zones via P P '� commercial addressable,wireless or, • Electrical Ratings for IN 2 and IN 3• conventional fire devices(2 onboard NACs providing up to4A notification • Maximum Loop Voltage:15VDC f power).'.Locking,mercantile red I enclosure,(surface or flush mount) • Maximum Loop Current: 1.2mA removable 16"x17"door with • Electrical Ratings for 3 PGM Outputs: 14.25"x16"base.Houses 16Ah batterybackup • Open Collector Outputs: Maximum voltage 3V when active; L ... .....,- _ ._._,__... 15V maximum when not active • Maximum PGM Sink Current:50mA mount StarLink Fire NAPGO COMMERCIAL FIRE CELLULAR&IP • Operating Environment 0 to 490 C(32 120°F),up to 93% humidity(non-condensing) 12V 333 Bayview Ave.,Amityville,NY 11701 USA 161 24V Universal FACP Support,auto-current sensing. 1-800-645-9445 •Fax:1-631-789-9292 NFPA Support all brands communicating in Contact ID and 4/2 www.napcosecurity.com StarUnk,Startink Fire,Firelink Signalil00%PanePowered Technology,Gemini&Gemini Commercial are trademarks of Napco.Vemon,LTE,etc.are trademarks of(heir respective companies.'StarLinkoffers full data cuveage in US from virtually all panel brands reporting in Contact ID or42. FbrfuldetakontheStarUnkudeupinammseeodneunderhVYAww.riapmsemri mm/sta&nk/stadinMppgrade/tPromosubiedtodrangew/opriornotice.LTEKespandaimsarebasedonthoseofarriers.Nedron®rankng,haseciontheRootMehiaUS National RoolSmre®Report 1H2O17. ©NAPCO,NAPCOSecuriV Technologies Inc.(NASDAQ:NSSC) A7342018.9 ECS = 125W SERIES Intelligent 125 Watt Amplifier The ECS-125W is an amplifier compatible with the Farenhyt Emergency Communication System. The ECS-125W is used to amplify audio messages for distribution throughout entire facilities. Since the ECS-125W is designed as a self-contained distributed amplifier,it can be conveniently located near the area of protection to reduce wiring demands.Each ECS- 125W is capable of producing 125-watts of audio power.Up to eight ECS-125W amplifiers can be used on the Emergency Communication System.The ECS-125W has its own power supply with battery backup and includes four speaker circuits which can be expanded to eight speaker circuits when used with the optional ECS-CE4.The ECS-125W is fully supervised by the main panel to identify the trouble conditions. INSTALLATION The ECS-125W Series can be surface-or flush-mounted. COMPATIBILITY The ECS-125W Series is compatible with the following Honeywell Farenhyt Series voice evacuation components: • IFP-300ECS/IFP-300ECSB • IFP-2100ECS/IFP-2100ECSB FEATURES AND BENEFITS • Complies with UL 86410th Edition and UL • Uses an easy-to-install wire harness to • Provides six-wire connection to the ECS 2572 2nd Edition Standards connect the ECS-CE4 audio circuit System: • Meets NFPA 72 standards expander -Two-wires for the voice bus connections • Provides SBUS addressable to support up • Extends remote installations up to 6,000 -Four-wires for the SBUS connections to eight ECS-125W amplifiers per system feet away from the ECS Series panel • Can be surface-or flush-mounted for a total of 1000 watts • Includes its own power supply and backup . Supports 120 VAC or 240 VAC operation • Each ECS-125W amplifier is supervised battery and has four onboard audio circuits • Selectable for 25V or 70.7V operation expandable to eight with the ECS-CE4 • Available in a red or a black cabinet expander for a system total of 64 audio circuits Honeywell Farenhyt Series ECS-125W SERIES TECHNICAL SPECIFICATIONS PHYSICAL ORDERING INFORMATION Flush Mount Dimensions: ECS-125W:Intelligent 125W Amplifier,red ' 14.05"W x 24.75"H x 3.04"D ECS-125WB:Intelligent 125W Amplifier, • - registered (36.08 W x 62.09 H x 8.07 D cm) black tradernark Overall Dimensions: ECS-125WHV:High Voltage(240V)125W International, 16.0"W x 26.25"H x 4.01"D Amplifier (40.06 W x 66.07 H x 10.05 D cm) ACCESSORIES document • intended • •. Color:Red or Black This ENVIRONMENTAL ECS-CE4:Audio Circuit Expander used for installation purposes. RBB:Remote Battery Box accessory _ Operating Temperature:32°F to 120°F cabinet.Use for backup batteries up to to • •ur product • • (0°C to 49°C) 35AH and batteries too large to fit into an • and accurate. cannot Humidity:10%to 93%relative humidity ECS-50W cabinet.SK-SCK:Seismic cover •- applications (non-condensing) Compliance Kit anticipate all requirements. ELECTRICAL STANDARDS AND CODES specifications _ • _ •chan•_ The ECS-125W Series Complies with the without • _ Module Voltage Standby *Alarm following standards and codes. Current Current • UL 864,loth Edition:Standard for Control Units for Fire Alarm Systems Country ECS-125W/B 120V 300mA 2200mA . UL 864,Local Protective Signaling Systems 25V 60 Hz - UL 2572,2nd Edition:Standard for Mass ECS-125WHV 240V 250mA 1250mA Notification Systems 25V 50Hz • UL 1711 *Fully loaded system • NFPA:-NFPA 13 Total Power: -NFPA 70 •Circuit 1:10OW max. -NFPA 72 •Circuit 2-8:50W max. AGENCY LISTINGS AND Main ECS PaneISBUS: APPROVALS Standby Current:10mA . UL Listed:S2766 Alarm Current:10mA • CSFM Approved:7300-0559:0173 Battery Charging Capacity:7—35AH - FDNY:Approved Battery Size:18AH max.allowed in the cabinet.Use the RBB accessory cabinet for larger batteries up to 35AH per system. Voice Integration.Wiring: • Six conductor •Two voice bus • FourSBUS THE FUTURE IS Honeywell Fire Solutions WHAT 12 Clintonville Road WE Northford,CT06472-1610 350772 I G 104-22 MAKE IT 203.484.7161 ©2022 Honeywell International Inc.www.farenhyt.com Honeywell Honeywell SMFM' MGM SK-PULL-SA / SK-PULL-DA Intelligent Pull Stations The SK-PULL-SA is a single action pull station requiring only one motion to activate the station.The SK-PULL-DA is a dual action pull station requiring two motions to active the station.The SK-PULL-SA and SK-PULL-DA are for use with Honeywell Silent Knight Series fire control panel(FACP). 4,,PULL I! Extremely easy to operate,the SK-PULL-DA and SK-PULL-SA provide a fast and practical means of manually initiating a fire alarm signal.The FACP recognizes each manual pull station by its specific address saving precious seconds in determining the location of an alarm. i INSTALLATION The SK-PULL-SA and SK-PULL-DA can be surface mounted to an SB-1/0 ~SIC-PULL-SA surface back box or semi-flush mounted on a standard single-gang with a minimum depth of 2.13"(5.40 cm)or double gang or 4"(10.61 cm)square — electrical box.You can also use the optional(System Sensor'PN BG TR) trim ring if the station is being semi-flush mounted. SK-PULL-DA FEATURES & BENEFITS • Installer can open • Key operated test and Meets the Americans • Reliable analog Handle latches in station without reset lock using lock with Disabilities Act communications for down position and the causing an alarm plate actuator Accessibility trouble-free operation word Activated condition Guidelines(ADAAG) appears,clearly • Key matches • Braille text on station • Dual-color LED is compatible FACP controls and operating handle indicating the station visible through handle locks mechanisms has been putted of station blinks green guidelines(Section • Rotary address .1.31131) switches for fast UL Listed,including • Meets ADA 4 to indicate normal UL 38,Standard of operation and remains requirement for 5 tbs ' Shell,door,and handle installation Manually Actuated maximum pull force to steady red in an alarm active molded from durable Signaling System condition LEXAN' • CSFM Listed • MEAListed SK-PULL-SA / SK-PULL-DA Technical Specifications For a complete listing of all compliance approvals and certifications,please visit PHYSICAL ORDERING INFORMATION www.slientknight.com. Dimensions:5.5"H x 4"W x 1.45"D(14 x 10.2 x SK-Pull-SA:Single Action Pull Station 3.7cm) Microsoft,Windows,and SK-Pull-DA:Dual Action Pull Station the Windows Logo are Housing Material:LEXAN polycarbonate resin registered trademarks Bi-Colored LED: ACCESSORIES or trademarks of Blinking Green:Normal BG-TR:Optional trim ring. Microsoft Corporation. Steady Red:Alarm SB-1/0:Surface backbox,indoor/outdoor. Silent Knight°,System Switch:Single pole,single throw(SPST)normally *Unless otherwise noted,specifications apply to Sensor'and Honeywell open(N/O)switch which closes upon activation of SK-Pull-SA and SK-Pull-DA are registered the pull station trademarks of Honeywell COMPATIBILITY International,Inc. ELECTRICAL The SK-PULL-SA AND SK-PULL-DA are This document is not Operating Voltage:15—32VDC compatible with the following Honeywell Silent intended to be used for SLC Standby and Alarm Current:350µA Knight fire alarm control panels: installation purposes.We Wire Gauge:Up to 12AWG(3.1 mm2) 6820:Addressable fire alarm control panel tryto informeepour ptoduct 6820EVS:Addressable fire alarm control panel date and accurate.We ENVIRONMENTAL with an emergency voice system. cannot cover all specific Operating Temperature:320E—120°F(OeC— 6808:Addressable fire alarm control panel applications or anticipate 49°C) 6700:Addressable fire alarm control panel all requirements.All specifications are subject Humidity:l0%-93%non-condensing 5700:Addressable fire alarm control panel to change without notice. 5808:Addressable fire alarm control panel For Technical Support, 5820XL:Addressable fire alarm control panel call800-446-6444. 5820XL-EVS:Addressable fire alarm control panel with an emergency voice system For more information Learn more about Honeywell Silent Knight and other products by visiting www.sitentknight.com 2 Clintonville lvilleR Knight Honeywell 12 Clintonville Road Northford,CT 06472 Doc 3501351 Rev E 111/17 SILENT' 800-328-0103 ©2017 Honeywell International Inc. ®I(NIIGHT 4 �~ S Km H EATmW I Addressable Heat Detectors The Silent Knight° SK-HEAT-W Series heat , detectors are designed for both performance and aesthetics. A new modern, sleek, : contemporary design and advanced thermal technologies make the SK-HEAT-W Series - ideal for both system operation and building design. The series includes a 135°F/571C fixed-temperature,rate-of-rise,and a 1801F/881C fixed high-temperature detectors and are direct replacements forthe SK-HEATSeries heat detectors.The point ID address,set using rotary decimal switches,provide specific detector locations.These thermal detectors provide effective,intelligent property protection in a variety of applications. • SK-HEAT-W offers 135°F fixed thermal detection. • SK-HEAT-ROR-W offers 135°F fixed and rate-of-rise thermal detection. • SK-HEAT-HT-W provides fixed high-temperature detection at 190°F. FEATURES AND BENEFITS • Designed to meet LIL 268 7th Edition • 360°-field viewing angle of the visual alarm • Designed for direct-surface or electrical- • Sleek and stylish contemporary design indicators(two bi-color LEDs);LEDs blink box mounting • Advanced thermal technology for fast green in Normal condition and turn on • Sealed against back pressure response steady red in Alarm • Plugs into separate base for ease of • Fixed temperature model(SK-HEAT-W) . Integral communications and built-in installation and maintenance factory preset to 135°F(57°C) device-type identification • SEMS screws forwiring of the separate base • Rate-of-rise model(SK-HEAT-ROR-W), . Remote test feature from the panel • Optional remote,single-gang LED 15°F(8.3°C)per minute . Built-in functional test switch activated by accessory • High temperature model(SK-HEAT-HT-W) external magnet • Optional sounder,relay,and isolator bases factory preset to 190°F(88°C) . Walk test with address display(an address • Optional flanged surface mounting kit • Addressable by device of 121 will blink the detector LED 12- • Rotary,decimal addressing(Refer to the (pause)-1) Silent Knight panel manuals for device . Low standby current capacity) Built-in tamper-resistant feature Honeywell • Two-wire SLC connection • LEDs blink every time the unit is polled SILBNT' ®KNIGHT APPLICATIONS B200SR-LF-IV:Ivory,Low Frequency Intelligent sounder base for Use thermal detectors for protection of property.For further retrofit applications information,refer to manual 156-6529,Applications Manual for B224RB-WH:White,plug-in System Sensor'relay base System Smoke Detectors,which provides detailed information on B224RB-IV:Ivory,plug-in System Sensor relay base detector spacing,placement,zoning,wiring,and special B224BI-WH:White,plug-in System Sensor isolator detector base applications. INSTALLATION B224BI-IV:Ivory,plug-in System Sensor isolator detector base The SK-HEAT-W Series plug-in intelligent thermal detectors use a ACCESSORIES separate base to simplify installation,service,and maintenance. TR300:White,replacement flange for B210LP or B300-6 bases Installation instructions are shipped with each detector. TR300-IV:Ivory,replacement flange for B210LP or B300-6 bases Mount base(all base types)on an electrical backbox which is at RA100Z(A):Remote 3-32 VDC LED annunciator,mounts to a U.S. least 1.5"(3.81 cm)deep.For a chart of compatible junction boxes, single-gang electrical box,for use with B501 and B300-6 bases see SK-61045. only Note:Because of the inherent supervision provided bythe SLC loop, M02-04-00:Test magnet end-of-line resistors are not required.Wiring"T-taps"or branches M02-09-00:Test magnet with telescoping handle are permitted for Style 4(Class"B")wiring. Note:When using relay or sounder bases,consult the SK-ISO CK300:White,detector color kit,pack of 10 installation sheet 156-3627 for device limitations between isolator CK300-IV:Ivory,detector color kit,pack of 10 modules and isolator bases. CK300-BL:Black,detector color kit,pack of 10 PRODUCT LINE INFORMATION SK-HEAT-W:White,low-profile intelligent 1351Ffixed thermal sensor SK-HEAT-ROR-W:White,low-profile intelligent rate-of-rise thermal sensor SK-HEAT-HT-W:White,low-profile intelligent 190°F fixed thermal sensor B300-6:White,standard flanged low-profile mounting base B300-6-BP:Bulk pack of B300-6,package contains 10 B300-6-IV:Ivory,standard flanged low-profile mounting base B501-WHITE:White,standard European flangeless mounting base B501-BL:Black,standard European flangeless mounting base B501-IV:Ivory,standard European flangeless mounting base B501-WHITE-BP:Bulk pack of B501-WHITE,contains 10 B200S-WH:White,Intelligent,programmable sounder base B200S-IV:Ivory,Intelligent,programmable sounder base B200SR-WH:White,Intelligent sounder base for retrofit applications B200SR-IV:Ivory,Intelligent sounder base for retrofit applications B200S-LF-WH:White,Low Frequency Intelligent,programmable sounderbase B200S-LF4V:Ivory,Low Frequency Intelligent,programmable sounderbase B200SR-LF-WH:White,Low Frequency Intelligent sounder base for retrofit applications Page 2 of 3—351637:13•7/1/2019 SK-HEAT-W SERIES TECHNICAL SPECIFICATIONS PHYSICAUENVI RON MENTAL AGENCY LISTINGS AND Size:2.0"(5.3 cm)high;base determines APPROVALS ' diameter These listings and approvals apply to the are registered trademarks of -13300-6:6.1"(15.6 cm)diameter modules specified inthis document.ln some Honeywell International, -8501:4"(10.2 cm)diameter cases,certain modules or applications mayThis document is o intended o be be listed bycertain approval agencies,or used for installation purposes.We For a complete list of detector bases,see listing may be in process.Consult factory for try t o keep our product info rmation SK-61045. latest fisting status. rate. Operating temperature range:SK-HEAT-W, . UL Listed:56228 cover all specificapplications or SK-HEAT-ROR-W:-4°Fto 100°F . FM Approved anticipate all requirements. (-200Cto3800 • CSFM:7270-0559:0511 specifications are SU bject to change SK-HEAT-HT-W:-4°Fto150°FC-20°Cto without notice. 66°C) Detector spacing:UL approved for 50 ft. Country of origin: (15.24 m)center to center;FM approved for 25 x 25 ft.(7.62 x 7.62 m)spacing Relative humidity:10%—93%non- condensing Thermal ratings:Fixed-temperature set point 135°F(570C),rate-of-rise detection 15°F(8.3°C)per minute,high temperature heat 190°F(88°C) ELECTRICAL SPECIFICATIONS Voltage range:15-32 volts DC peak Standby current(max.avg.):200uA C 24 VDC(one communication every 5 seconds with LED enabled) LED current(max.):4.5mA @ 24 VDC("ON") Honeywell Silent Knight 12 Clintonville Road Northford,CT 06472-1610 Honeywell 203.484.7161 3516371 B 107/19 ®SILENT' www.sllentknlght.com ©2019 Honeywell International Inc. EMGHT c,a C01224A SYSTEMI Az SENSOR® C01224 Series Carbon Monoxide - -- Detectors with RealTest° C : ' • -t Technology Y k C01224T The System Sensor CO1224T CO1224TR, and CO1224A ` w. (Canada) Carbon Monoxide(CO)Detectors use a highly accurate and reliable electrochemical sensing cell to C01224TR provide early warning of dangerous CO levels. Features When dangerous amounts of CO are detected,the CO1224 Series CO detectors alert residents by sounding and flashing a temp • A 10 year end-of-life timer 4 signal alarm.With 24/7 central station monitoring,residents are • RealTest@ enables a functional test using canned CO guaranteed protection whether they are away from home,sleeping, • A code-required trouble relay or already suffering from the effects of CO. • Wiring supervision with SEMS terminals The C01224 Series detectors are designed for system operation. • 12/24 VDC These detectors are fully listed to UL 2075(US models only)and • A low current draw of 20 mA in standby and 40 mA in alarm CSA 6.19-01 (Canada model only)and offer a code-required trouble • Versatile mounting for wall and ceiling relay to send a sensor failure or end-of-life signal to the control panel and the central station.The C01224 Series detectors also • Accurate and reliable electrochemical sensing technology use SEMS-type terminal Philips head screws for quicker and more • Optional CO-PLATE CO Detector Replacement Plate to upgrade positive wiring connections and code-required wiring supervision. previously installed competitor detectors to the C01224T or With a low current draw,these detectors enable more devices to be CO1224A, connected to the panel,limiting the need to purchase extra power • C01224T tested up to 12,000 feet above sea level supplies or more expensive panels.As 12/24 VDC detectors,the C01224 Series detectors will operate on most industry security and fire alarm control panels. With RealTest®technology,the CO gas sensing cell used in the C01224 Series CO detectors can be tested using a CO gas agent, fully meeting the requirements of NFPA 720:2009(US models only). Simply put the detector into RealTest mode,spray a small amount of CO into the detector per the installation instructions,and within seconds the detector will alarm,indicating successful gas entry.(See the reverse page or the user manual for complete instructions.) Agency Listings UNote:CO1224T& LCO1224TR are in full compliance with UL LISTED 2075 and C01224A is in full compliance with E307195 E304075 ULC CSA 6.19-01. C01224 Series Detectors Carbon Monoxide Detector Specifications Arch itectural/Engineering Specifications Carbon monoxide(CO)detector shall be a system-connected System Sensor model number C01224T or C01224TR listed to Underwriters Laboratories UL 2075 for Gas and Vapor Detectors and Sensors.The Canadian model C01224A,is ULC listed to CSA 6.19-01,for residential carbon monoxide alarm devices.The detector shall be equipped with a sounder and a trouble relay.The detector's base shall be able to mount to a single-gang electrical box or direct(surface)mount to the wall or ceiling.Wiring connections shall be made by means of SEMS screws.The detector shall provide dual-color LED indication that blinks to indicate normal standby,alarm,or end-of-life.When the sensor supervision is in a trouble condition,the detector shall send a trouble signal to the panel.When the detector gives a trouble or end-of-life signal,the detector shall be replaced.The detector shall provide a means to test CO gas entry into the CO sensing cell.The detector shall provide this with a test mode that accepts CO gas from a test agent and alarms immediately upon sensing CO entry.For the C01224T only, the detector shall perform in the detection of CO up to 12,000 feet above sea level and alarm within the time specified by ANSI/UL 2034 for CO concentrations of 70, 150 and 400 parts per million(ppm),as verified by a Nationally Recognized Test Laboratory. Electrical Specifications Voltage 12/24 VDC Audible Signal 85 dB in alarm Standby Current 20 mA Alarm Current 40 mA(75 mA test) Alarm Contact Ratings 0.5 A @ 30 VDC Trouble Contact Ratings 0.5 A @ 30 VDC Physical Specifications Size:C01224T&C01224A Length:5.1 in(130 mm),Width: 3.3 in(84 mm),Height: 1.3 in(33 mm) Size:C01224TR Diameter:6.0 in(152 mm),Height: 1.3 in(33 mm) Approximate Weight C01224T&C01224A:7 oz(198 g);C01224TR:11 oz(312 g) Operating Temperature Range 32°F to 104°F(0°C to 40°C) Operating Humidity Range 22 to 90%RH Input Terminals 14 to 22 AWG Mounting Single-gang back box;surface mount to wall or ceiling Operation Modes Operation Mode Green LED Red LED Sounder Normal(standby) Blink 1 per minute — — Alarm — Blink in temp 4 pattern Sound in temp 4 pattern RealTest®Feature: The System Sensor C01224 Series CO Detectors enable evaluation of the functionality of the CO sensing cell using a canned CO test agent. NOTE:Check with local codes and the AHJ to determineif a functional gas test is desired for an installation. ' erg Push and hold the Test(Hush button for Spray canned CO agent into the Verify CO sensing at the control panel. two seconds to enter RealTest mode.The detector. The detector will automatically exit green LED will flash once every second to RealTest alarm mode after about 20-60 indicate RealTest mode has started. seconds. Hush Feature: Pushing the Test/Hush button will silence the sounder for 5 minutes(except in RealTest mode). Trouble Feature: When the detector is in a trouble condition,it will send a trouble signal to the panel. End-of-Life Timer: After the detector's internal sensor has reached the end of its life,a trouble signal will be sent to the panel to indicate it is time to replace the detector.An electrochemical CO detector lifespan is about ten years. The detector must be replaced by the date marked on the inside of the product. CO-PLATE: System Sensor also offers the CO-PLATE CO Detector Replacement Plate to cover the footprint(when necessary) �`w• of previously installed competitive carbon monoxide detectors that require replacement. Ordering Information CO-PLATE DescriptionPart No. C01224T 12/24 volt,6-wire system-monitored carbon monoxide detector with RealTest®Technology(US only) CU1224 R 12/24 volt,6-wire system-monitored round carbon monoxide detector with RealTest®Technology(US only) CO1224A 12/24 volt,6-wire system-monitored carbon monoxide detector with RealTest®Technology(Canada only) CO-PLATE CO detector replacement plate to cover the footprint of previously installed competitive detectors(US&Canada) SYSTEM US:3825 Ohio Avenue Canada:6581 Kitimat Rd,Unit 6 02016 System Sensor.Product specifications subject to St.Charles,IL 60174 Mississauga,Ontario L5N 3T5 change without notice.Visit our websites for current product SENSOR® 800-SENSOR2 800-SENSOR2 Information,including the latest version of this data sheet. systemsensor.com systemsensor.ca CODS88600•10116 Honeywell ®SILENT' KNIGHT SK-MINIMON Intelligent Mini Monitor Module The SK-MINIMON is an addressable monitor modules for use with the Honeywell Silent Knight fire alarm control panels(FACPs).The SK- V °� MINIMON acts as an interface to contact devices,such as waterflow ` switches and pull stations.The SK-MINIMON supports Class B supervised wiring to the load device.Conventional 4-wire smoke detectors can be Y monitored for alarm and trouble conditions The SK-MINIMON can be mounted in a single gang junction box directly , l f behind the monitored device.Its small size and light weight allow it to be i I installed without rigid mounting requirements. i SK-MINIMON - INSTALLATION The SK-MINIMON can be mounted in a single gang junction box directly behind the monitored device.Its small size and Lightweight allow it to be installed without rigid mounting requirements. FEATURES & BENEFITS • Single contact monitor • Rotary address • SK-Minimon support switches for fast for Class B(Style B) installation contact monitor wiring • UL Listed • Small and lightweight • CSFM Listed size allows for flexible . FM Approved mounting options SK-MINIMON Technical Specifications For a complete listing of all compliance approvals and certifications,please visit PHYSICAL ORDERING INFORMATION www.sitentknight.com. Dimensions:2.75"W x 1.3"H x 0.5"D SK-MINIMON:Mini monitoring module Microsoft,Windows,and Weight:1.2 oz(37 g) the Windows Logo are COMPATIBILITY registered trademarks ELECTRICAL The SK-MINIMON is compatible with the or trademarks of Operating Voltage:15-32VDC following Honeywell Silent Knight fire alarm Microsoft Corporation, SLC Standbyand Alarm Current:350 to control panels: I- Silent Knight',System End-of-Line Resistance:47K n 6820:Addressable fire alarm control panel Sensor'and Honeywell' Initiating device circuit wiring resistance:1,500f2 6820EVS:Addressable fire alarm control panel are registered max with an emergency voice system. trademarks of Honeywell SLC loop resistance:4052 max 6808:Addressable fire alarm control panel International,Inc. Wire Length:6"min. 6700:Addressable fire alarm control panel This document is not 5700:Addressable fire alarm control panel intended to be used for ENVIRONMENTAL 5808:Addressable fire alarm control panel installation purposes.We try to keep our product Operating Temperature:321F-120°F(0°C- 5820XL:Addressable fire alarm control panel information up-to 49°C) 5820XL-EVS:Addressable fire alarm control panel date and accurate.We Humidity:10%-93%non-condensing with an emergency voice system cannot cover all specific applications or anticipate all requirements.All specifications are subject to change without notice. For Technical Support, cat1800-446-6444. For more information Learn more about Honeywell Silent Knight and other products by visiting www.sitentknight.com Honeyw2Clintelville Silent Knight Honeywell 12 Clintonville Road Northford,CT 06472 Doc 3501331 Rev G 1 11/17 SILENT 800-328-0103 ©2017 Honeywell International Inc. ®KNIGHT SYSTEM �.� SENSOR® = r. Indoor Selectable- a°' Output Speaker - l - - Strobes and Dual 5 Voltage Evacuation �,� Speakers for Ceiling Applications ; . System Sensor L-Series selectable-output speaker strobes and dual-voltage evacuation speakers can reduce ground faults and enable faster installation with lower current draw = and modern aesthetics. System Sensor L-Series of speakers and speaker strobes reduce costly ground faults using a plug-in design and universal Features mounting plate that allow the installer to pre-wire mounting plates, • Plug-in design and protective cover reduce ground faults dress the wires,and confirm wiring continuity before plugging in the speakers. In addition,a protective plastic cover prevents nicked • Universal mounting plate with an onboard shorting spring tests wires by covering exposed speaker components. wiring continuity before installation • No extension ring required These devices also enable faster installations by providing instant • Field selectable candela settings on ceiling units: feedback to ensure that wiring is properly connected,rotary switches 15,30,75,95, 115, 150,and 177 to select voltage and power settings,and 7 field-selectable candela • Automatic selection of 12-or 24-volt operation settings for both wall and ceiling speaker strobes. at 15 and 30 candela The low total harmonic distortion of the SP speaker offers high fidelity • Rotary switch simplifies field selection of speaker voltage(25 sound output while still offering high volume sound output for use in and 70.7 Vrms)and power settings(1/4,1/2, 1 and 2 watts) high ambient noise applications. • Speakers offer high fidelity and high volume sound output L-Series makes installation easy • 520 Hz+/-10%square wave tone capable with compatible FACP .Attach a universal mounting plate to a 4 x 4 x 21/8 inch back box. • Compatible with System Sensor synchronization protocol Flush-mount applications do not require an extension ring. • Electrical compatibility with existing SpectrAlert and SpectrAlert •Connect the notification appliance circuit or speaker wiring to the Advance products terminals on the mounting plate. •Attach the speaker or speaker strobe to the mounting plate by • Tamper resistant construction inserting the product tabs into the mounting plate grooves.Hinge • Updated modern aesthetics the device into position to lock the product pins into the mounting plate terminals.The device will temporarily hold in place with a Agency Listings catch until it is secured with a captured mounting screw. SIGNALING LISTED APPROVED 54048 FM approved except 7320-1653 0505 for ALERT models 3057493 AVDS866-03.03/23/2018•Page 1 L-Series Speaker and Speaker Strobe Specifications Specifications L-Series speaker and speaker strobes shall mount to a 4 x 4 x 21/6-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate.Also,L-Series speaker strobes,when used with the SynceCircuitTM Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the SynceCircuit Module,12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 320F and 120°F from a regulated DC,or full-wave rectified,unfiltered power supply.Speaker strobes shall have field-selectable candela settings including 15,30,75,95,115,150,177. Speaker The speaker shall be a System Sensor L-Series model dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms.It should be listed to UL 1480 and shall be approved for fire protective service.The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 320F and 120°F.The speaker shall have power taps and voltage that are selected by rotary switches. Speaker Strobe combination The speaker strobe shall be a System Sensor L-Series model listed to UL1480 and UL 1971 and be approved for fire protective signaling systems.The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch,and shall have a frequency range of 400 to 4,000 Hz.The speaker shall have power taps that are selected by rotary switch.The strobe shall comply with the NFPA 72 requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Synchronization Module The module shall be a System Sensor SynceCircuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize SpectrAlert strobes at 1 Hz.The module shall mount to a 4"/16 x 411/16 x 21/6-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical Specifications Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Dimensions,Ceiling-Mount Diameter Depth SPC Speaker 6.8 in,173 mm 1.0 in,25 mm With Surface Mount Back Box 6.9 in, 176 mm 3.5 in,89 mm SPSC Speaker Strobe 6.8 in, 173 mm 2.8 in,73 mm With Surface Mount Back Box 6.9 in, 176 mm 5.37 in,136 mm 'When using 12AWG, 14 AWG,or adding extra wires in the box,a deeper box or extension ring is recommended. Electrical/Operating Nominal Voltage(speakers) 25 Volts or 70.7 Volts(nominal) Maximum Supervisory Voltage(speakers) 50 VDC Strobe Flash Rate 1 flash per second Nominal Voltage(strobes) Regulated 12 VDC or regulated 24 VDC/FWR 1,2 Operating Voltage Range(includes fire 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) alarm panels with built in sync) Operating Voltage with MDL3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) Frequency Range 400 to 4,000 Hz3 Power 1/4,1/2,1,2 watts 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.Strobe products will operate at 12 V nominal only for 15 and 30 cd. 3.520 Hz+/-10%square wave tone capable with compatible FACP. AV03866-03.03/23/2018•Page 2 Surface Mounting o o O i� o m A0504-01 `Eel t A0520-01 Ceiling Speaker with Surface Mount Back Box Ceiling Speaker Strobe with Surface Mount Back Box o 0Oo 0 0 p O o 0 A0542-00 Ceiling Speaker Strobe with Trim Ring and 4"Square Electrical Box L-Series Ordering Information Ceiling Mount White Red Description SPCWL SPCRL Speaker only SPSCWL SPSCRL Speaker Strobe SPSCWL-P — Plain,Speaker Strobe SPSCWL-SP — Fuego,Speaker Strobe SPSCWL-CLR-ALERT — Alert,Speaker Strobe,Clear Lens Accessories White Red Description SBBCWL SBBCWL Universal Ceiling Surface Mount Back Box TRC-2W TRC-2 Universal Ceiling Trim Ring SYSTEM 3825 Ohio Avenue•St.Charles, IL 60174 ©2018 System Sensor. Phone:800-SENSOR2•Fax:630-377-6495 Product specifications subject to change without notice.Visit systemsensorcom SENSOR for current product information,Including the latest version of this data sheet www.systemsensor.com AVDS866-03.03/23/2018 �+ NNW UL Current Draw Data StrobeUL Max. 8 to 17.5 Volts 16 to 33 Volts Candela DC DC FWR 15 87 41 60 30 153 63 86 75 NA 111 142 95 NA 134 164 115 NA 158 191 150 NA 189 228 177 NA 226 264 SpeakerOutput Setting UL Reverberant(dBA @10 ft) UL Anechoic(dBA @10 ft) 1/4 W 79 79 1/2 W 82 82 1 W 85 85 -2 W 88 88 OutputCeiling-Mount Speaker Strobe Sound Setting UL Reverberant(dBA @10 ft) UL Anechoic(dBA @10 ft) 1/4 W 77 77 112 W 80 80 1 W 83 83 2 W 86 86 L-Series Dimensions W 3 69'd (173 mm) (tSAmm) (41.66 mm) II �)�111 1 1, III R7 A0543-00 Ceiling Speaker 6.6'di.. mm) (4t66 mm) (173 mm) 1.76' (44.7mm) Fh A0544-00 Ceiling Speaker Strobe AVOS866-03.03/23/2018•Page 3 SYSTEM t� SENSOR® Indoor Selectable- i Output Horns, ; ler ":kt' rt;j �t! Strobes, and -- - _ Horn Strobes for Wall Applications ( E, System Sensor L-Series audible visible notificationm$, -j, products are rich with features guaranteed to cut e . o$ JR. installation times and maximize profits with lower current draw and modern aesthetics. Features • Updated Modern Aesthetics The System Sensor L-Series offers the most versatile and • Small profile devices for Horns and Horn Strobes easy-to-use line of horns,strobes,and horn strobes in the industry • Plug-in design with minimal intrusion into the back box with lower current draws and modern aesthetics.With white and red • Tamper-resistant construction plastic housings,standard and compact devices,and plain,FIRE, and FUEGO-printed devices,System Sensor L-Series can • Automatic selection of 12-or 24-volt operation at 15 and 30 meet virtually any application requirement. candela • Field-selectable candela settings on wall units: The L-Series line of wall-mount horns,strobes,and horn strobes 15,30,75,95, 110, 135,and 185 include a variety of features that increase their application versatility • Horn rated at 88+dBA at 16 volts while simplifying installation.All devices feature plug-in designs • Rotary switch for horn tone and two volume selections with minimal intrusion into the back box,making installations fast and foolproof while virtually eliminating costly and time-consuming • Mounting plate for all standard and all compact wall units ground faults. • Mounting plate shorting spring checks wiring continuity before device installation To further simplify installation and protect devices from construction • Electrically compatible with legacy SpectrAlert and SpectrAlert damage,the L-Series utilizes a universal mounting plate for all Advance devices models with an onboard shorting spring,so installers can test wiring • Compatible with MDL3 sync module continuity before the device is installed. • Strobes and Horn Strobes listed for wall mounting only Installers can also easily adapt devices to a suit a wide range • Horns listed for wall or ceiling use of application requirements using field-selectable candela settings, automatic selection of 12-or 24-volt operation,and a rotary switch for horn tones with two volume selections. Agency Listings SIGNALING & LISTED APPXOVEO S5512 FM approved except 7125-1653:0504 S4011 for ALERT models 7135-1653.0503 3057383,3057072 AVDS865-05.2/22/2018•Page 1 L-Series Specifications Arch itecVEngi neer Specifications General L-Series standard horns,strobes,and horn strobes shall mount to a standard 2 x 4 x 17/8-inch back box,4 x 4 x 1'/2-inch back box,4-inch octagon back box,or double-gang back box.L-Series compact products shall mount to a single-gang 2 x 4 x 17/8-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products for all standard models and a separate universal mounting plate shall be used for mounting wall compact models.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,L-Series products,when used with the Sync•Circuit-Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module,12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts.Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15,30,75,95,110, 135,and 185. Strobe The strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor SynceCircuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize Strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 411/16 x 4"/16 x 21/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC or regulated 24 DC/FWR' Operating Voltage Range2 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(Including lens) 5.6"L x 4.7"W x 1.91-D(143 mm L x 119 mm W x 49 mm D) Compact Wall-Mount Dimensions(including lens) 5.26"L x 3.46"W x 1.91"D(133 mm L x 88 mm W x 49 mm D) Horn Dimensions 5.6-L x 4.7-W x 1.25"D(143 mm L x 119 mm W x 32 mm D) Compact Horn Dimensions 5.25"L x 3.45"W x 1.25"D(133 mm L x 88 mm W x 32 mm D) 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.Strobe products will operate at 12 V nominal only for 15 cd and 30 cd. AVDS865-05.2/2212018-Page 2 UL Current Draw Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-175 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC DC FWR Sound Pattem dB DC DC FWR Candela 15 88 43 60 Temporal High 39 44 54 Range 30 143 63 83 Temporal Low 28 32 54 75 N/A 107 136 Non-Temporal High 43 47 54 95 N/A 121 155 Non-Temporal Low 29 32 54 110 N/A 148 179 3.1 KHz Temporal High 39 41 54 135 N/A 172 209 3.1 KHz Temporal Low 29 32 54 185 N/A 222 257 3.1 KHz Non-Temporal High 42 43 54 3.1 KHz Non-Temporal Low 28 29 54 Coded High 43 47 54 3.1 KHz Coded High 42 43 54 UIL Max.Current Draw(mA RMS),Wall Horn Strobe,Candela Range(15-185 cd) 8-17.5 Volts 16-33 Volts DC Input 15cd 30cd 15cd 30cd 75cd 95cd 110cd 135cd 185cd Temporal High 98 158 54 74 121 142 162 196 245 Temporal Low 93 154 44 65 111 133 157 184 235 Non-Temporal High 106 166 73 94 139 160 182 211 262 Non-Temportal Low 93 156 51 71 119 139 162 190 239 3.1 K Temporal High 93 156 53 73 119 140 164 190 242 3.1 K Temporal Low 91 154 45 66 112 133 160 185 235 3.11K Non-Temporal High 99 162 69 90 135 157 175 208 261 3.1 K Non-Temporal Low 93 156 52 72 119 138 162 192 242 16-33 Volts FWR Input 15cd 30cd 75cd 95cd 110cd 135cd 185cd Temporal High 83 107 156 177 198 234 287 Temporal Low 68 91 145 165 185 223 271 Non-Temporal High 111 135 185 207 230 264 316 Non-Temportal Low 79 104 157 175 197 235 283 3.1 K Temporal High 81 105 155 177 196 234 284 3.1 K Temporal Low 68 90 145 166 186 222 276 3.1 K Non-Temporal High 104 131 177 204 230• 264 326 3.1 K Non-Temporal Low 77 102 156 177 199 234 291 Horn Tones and Sound Output Data StrobeHorn and Horn • .: 6-17.5 16-33 Switch Volts Volts Position Sound Pattern dB DC DC FWR 1 Temporal High 84 89 89 2 Temporal Low 75 83 83 3 Non-Temporal High 85 90 90 4 Non-Temporal Low 76 84 84 5 3.1 KHz Temporal High 83 88 88 6 3.1 KHz Temporal Low 76 82 82 7 3.1 KHz Non-Temporal High 84 89 89 8 3.1 KHz Non-Temporal Low 77 83 83 9* Coded High 85 90 90 10* 3.1 KHz Coded High 84 89 89. *Settings 9 and 10 are not available on 2-wire horn strobes.Temporal coding must be provided by the NAC.If the NAC voltage is held constant,the horn output remains constantly on. AVDS865-05.2/22/2018•Page 3 L-Series Dimensions 121" 3Afi" 31" 48.5 mm 39 mm Lu' 3M. 155" 88 mm 1.25° 32 mm (9,1 CM) (3.9 CM) 32 mm 0 0 I!P o 5ZV? d�t,,,,0;0,4 5.38° 133.9 mm 5.27" 0 ��00 (13.7 cm) O 133.9 mm 00000000000 L L4 0 0 0 A0548-00 A0547-00 A0557-00 Compact Strobe,Horn Strobe Compact Horn Compact Wall Surface Mount Back Box SBBGRL,SBBGWL 4.79" (11.94 cm) 1.91" 4.7" 1.25° 4b2' (4.85 cm) 119 mm L85' 32 mm (12.24 cm) 1.25" (4.69 cm) (3.18 mm) F ! F ® o Jcm) l 5.67° 5.78" :14. O( 144mm oo 68cm) o°aosa0000 P t4o.4ti .440�40. A0550-00 A0549-00 A0554-01 Strobe,Horn Strobe Horn Wall Surface Mount Back Box SBBRUSBBWL L-Series Ordering Information DescriptionModel - scription Wall Horn Strobes Horns* P2RL 2-Wire,Horn Strobe,Red HRL* Horn,Red P2WL 2-Wire,Horn Strobe,White HWL* Horn,White P2GRL 2-Wire,Compact Horn Strobe,Red HGRL* Compact Horn,Red P2GWL 2-Wire,Comp 2 fils act Horn Strobe,White HGWL* Compact Horn,White P2RL-P 2-Wire,Horn Strobe,Red,Plain Accessories P2WL-P 2-Wire,Horn Strobe,White,Plain TR-2 Universal Wall Trim Ring Red P2RL-SP 2-Wire,Horn Strobe,Red,FUEGO TR-2W Universal Wall Trim Ring White P2WL-SP '2-Wire,Horn Strobe,White,FUEGO SBBRL Wall Surface Mount Back Box,Red P4RL 4-Wire,Horn Strobe,Red SBBWL Wall Surface Mount Back Box,White P4WL 4-Wire,Horn Strobe,White SBBGRL Compact Wall Surface Mount Back Box,Red Wall Strobes SBBGWL Compact Wall Surface Mount Back Box,White SRL Strobe,Red SWL Strobe,White SGRL Compact Strobe,Red SGWL Compact Strobe,White SRL-P Strobe,Red,Plain SWL-P Strobe,White,Plain SRL-SP Strobe,Red,FUEGO SWL-CLR-ALERT Strobe,White,ALERT Notes: All-P models have a plain housing(no"FIRE"marking on cover). All-SP models have"FUEGO"marking on cover. All-ALERT models have"ALERT"marking on cover. *Horn-only models are listed for wall or ceiling use. SYSTEM 3825 Ohio Avenue is St.Charles, IL 60174 ©2018 System Sens- �� SENSOR® Phone:800 SENSOR2•Fax:630 377-6495 Pmrcurreduct tyro product ssrmati to change ngtheltesnotice.sionofthisdatasheet. for current product information,including the latest version of this data sheet. www.systemsensor.com AVDS865-05.2/22/2018 UL Current Draw Data UL Max Strobe Current Draw(mA RMS) 8 to 17.5 Volts 16 to 33 Volts Candela DC DC FWR 15 88 43 60 30 143 63 83 75 N/A 107 136 95 N/A 121 155 110 N/A 148 179 135 N/A 172 209 185 N/A 222 257 Sound Output Speaker ..- 1/4W 1/2W 1 W 2W UL Reverberant(dBA @10 ft) 77 80 83 86 UL Anechoic(dBA @10 ft) 77 80 83 86 Sound Output Speaker 1/4W 1/2W 1W 2W UL Reverberant(dBA @10 ft) 79 82 85 88 UL Anechoic(dBA @10 ft) 79 82 85 88 L-Series Dimensions 0.97° 1.63" (24.64 mm) (41.66 mm) 2.3" 1.63" 5 5" (58 mm) (41.66 mm) (127 mm) (127 mm) 1.39° (35.31 mm) 6.5" 6.51 (165 mm) (165 mm) 0 1 1 BB 10 1. 11,/ 1181p1'lll,1',p01,1 A0555-01 A0556-01 Wall-Mount Speaker Wall-Mount Speaker Strobe AVDS867-03.616/2019•Page 3 Surface Mounting m c ........... AO.A ® ® 0°A`AAAA AAAAgA9 OAAAAAllig.. °°g8 t ® ap16 °8 A'AgAgA9gAgAp A ®®®A AAAAAAAAAAAAAAAAU I's O010!01 U0 Q.0�00 goo, uopa°p°0pov ® ea 9AAA j A � AAAA '1 OOOA '1 ooAo tit oAao � oae�eo. i•r�r�'�i��i'�'''1 a°r'rh'y'6 A0523-01 Wall-Mount Speaker Strobe with SBBSPRU SBBSPWL Surface Mount Back Box L-Series Ordering Information White , Red Description SPWL SPRL Speaker only SPSWL SPSR Speaker Strobe SPSWL-P SPSRL-P Plain Speaker Strobe SPSWL-ALERT — Speaker Strobe,Amber Lens SPSWL-CLR-ALERT — Speaker Strobe Clear Lens SPSRL-SP Speaker Strobe,Fuego Accessories White Red Description RFPW RFP 7 in x 9.5 in Retrofit Plate SBBSPWL SBBSPRL Surface Mount Back Box for Speakers and Speaker Strobes TR-2W TR-2 Wall Mount Trim Ring Notes: All-P models have a plain housing(no"FIRE"marking on the cover) SYSTEM3825 Ohio Avenue•St.Charles, IL 60174 02019 System Sensor. SENSOR' Phone:800-SENSOR2•Fax:630-377-6495 Fforcurre t"pro uctI subject tochangewtheltestvesionofthisdatasheet. for current product Information,including the latest version of this data sheet. www.systemsensor.com AVDS867-03.6/6/2019 wr SYSTEM SENSOR® Outdoor Selectable- Output Horns, Strobes and Horn Strobes for Wall Applications SPECTRAIert SpectrAlert®Advance outdoor audible visible products a u v sa N c E are rich with features that cut installation times and maximize profits. Features SpectrAlert Advance offers the broadest line of outdoor horns, • Weatherproof per NEMA 4X, IP56 strobes,and horn strobes in the industry.With white or red plastic housings,wall or ceiling mounting options,and plain or FIRE-printed • Listed to UL 1638(strobe)and UL 464(horn) devices,SpectrAlert Advance can meet virtually any application • Compatible with System Sensor synchronization protocol and requirement,including indoor,outdoor,wet,and dry applications in legacy SpectrAlert products temperatures from—40oF to 151IF. • Field-selectable candela settings: 15, 15/75,30,75,95, 110, 115, Like the entire SpectrAlert Advance line,outdoor horns,strobes, 135, 150, 177,and 185 and horn strobes for wall applications include a variety of features • Automatic selection of 12-or 24-volt operation at 15 and that increase application flexibility and simplify installation.First, 15/75 candela field-selectable settings,including candela,automatic selection of • Rotary switch for horn tone and three volume selections 12-or 24-volt operation,horn tones,and three volume options enable • Horn rated at 88+dBA at 16 volts installers to easily adapt devices to meet requirements. • Rated from—40°F to 151 IF Next,SpectrAlert Advance devices use a universal mounting plate • Universal mounting plate with an onboard shorting spring that for both wall and ceiling applications.This mounting plate includes tests wiring continuity before devices are installed an onboard shorting spring that ensures wiring continuity before • Plug-in design with minimal intrusion into the back box devices are installed,so installers can verify proper wiring without mounting the devices and exposing them to potential construction • Tamper-resistant construction damage.Once the plates are mounted,all SpectrAlert Advance • Listed for ceiling or wall mounting devices utilize a plug-in design with a single captured screw to speed installation and virtually eliminate costly ground faults. Outdoor devices ship with weatherproof plastic back boxes(metal back boxes are available separately)that accommodate in-and- Agency Listings out wiring for daisy chaining devices.Plastic back boxes feature removable side flanges and improved resistance to saltwater SIGNALING corrosion. Knock-outs located on the back eliminate the need to drill LIS F M MEA holes for screw-in mounting.Plastic and metal weatherproof back boxes come with 3/4-inch top and bottom conduit entries and 3/4-inch 7300-1653 187(outdoor strobes) 54011(chimes,horn strobes,horns) APPROVED approved 7125-1653.188(horn strobes, knock-outs at the back.A screw-in NPT plug with an O-ring gasket chime strobes) S3593(outdoor and alert strobes) 3023572 MEA452-05-E 7135-1653:189(horns,chimes) for a watertight seal is included with each back box. i SpectrAlert Advance Outdoor Horn,Strobe,and Horn Strobe Specifications Architect/Engineer Specifications General SpectrAlert Advance outdoor horns,strobes,and horn strobes shall mount to a weatherproof back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate. Also,SpectrAlert Advance products,when used with the Sync-Circuit'"Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync-Circuit Module,12-volt-rated notification appliance circuit outputs shall operate between 9 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 17 and 33 volts.Outdoor SpectrAlert Advance products shall operate between—40 and 151 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply.Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75,30,75,95, 110, 115,135,150, 177,and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL.The strobe shall be suitable for use in wet environments. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options shall be set by a multiple position switch. On four-wire products,the strobe shall be powered independently of the sounder.The horn or horn strobe models shall operate on a coded or non-coded power supply.The horn strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL. The horn strobe shall be suitable for use in wet environments. Physical/Electrical Specifications Operating Temperature —40°F to 151°F(-40°C to 66°C) Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Range2 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(including lens) 5.6"L x 4.7"W x 2.5"D(142 mm L x 119 mm W x 64 mm D) Horn Dimensions 5.6"L x 4.7-W x 1.3"D(142 mm L x 119 mm W x 33 mm D) Wall-Mount Weatherproof Back Box Dimensions(SA-WBB) 5.7"L x 5.1"W x 2.0"D(145 mm L x 130 mm W x 51 mm D) Notes: 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products will operate at 12 V nominal only for 15 and 15/75 cd. AVDS01201 1 UL Current Draw Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Sound Pattern dB DC FWR DC FWR Standard 15 123 128 66 71 Temporal High 57 55 69 75 Candela 15/75 142 148 77 81 Temporal Medium 44 49 58 69 Range 30 NA NA 94 96 Temporal Low 38 44 44 48 75 NA NA 158 153 Non-Temporal High 57 56 69 75 95 NA NA 181 176 Non-Temporal Medium 42 50 60 69 110 NA NA 202 195 Non-Temporal Low 41 44 50 50 115 NA NA 210 205 Coded High 57 55 69 75 High 135 NA NA 228 207 Coded Medium 44 51 56 69 Candela 150 NA NA 246 220 Coded Low 40 46 52 50 Range 177 NA NA 281 251 185 NA NA 286 258 Strobe,UL Max.Current Draw(mA RMS),2-Wire Horn 8-17.5 Volts 16-33 Volts DC Input 15 15/75 15 15175 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103. 160 184 202 206 Temporal Low 129 151 76 86 101, 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 Strobe,UL Max.Current Draw(mA RMS),2-Wire Horn Candela16-33 Volts 16-33 Volts DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 Candela Derating Horn Tones and Sound Output Data For K series products used at low temperatures,listed Horn and Horn Strobe Output candela ratings must be reduced in accordance with 8--.175 16-33 24-Volt Nominal this table. Switch Sound Volts Volts Reverberant Anechoic Strobe Output(cd) Position Pattern dB DC FWR DC FWR DC FWR DC FWR Listed Candela Candela rating at-40°F 1 Temporal High 78 78 84 84 88 88 99 98 15 2 Temporal Medium 74 74 80 80 86 86 96 96 15/75 Do not use below 32°F 3 Temporal Low 71 73 76 76 83 80 94 89 30 4 Non- High 75 44 Temporal 82 82 88 88 93 92 100 100 95 70 5 Non- Medium 110 110 Temporal 78 78 85 85 90 90 98 98 115 115 6 Non- Low 135 135 Temporal 75 75 81 81 88 84 96 92 150 150 7t Coded High 82 82 88 88 93 92 101 101 177 177 8t Coded Medium 78 78 85 85 90 90 97 98 185 185 9t Coded Low 75 75 81 81 88 85 96 92 tSettings 7,8,and 9 are not available on 2-wire horn strobe. AVDS01201 SpectrAlert Advance Diagrams 4.7" 2.5" 5.6" ° O 0 Wall-Mount Horn Strobes Wall Plastic Weatherproof Back Box Wall-Mount Horn Strobe with Plastic Weatherproof Back Box SpectrAlert Advance Ordering Information ModelDescription Wall Horn Strobes P2RK*t 2-Wire Horn Strobe,Standard cd,Red,Outdoor(includes plastic weatherproof back box) P2RHK*t 2-Wire Horn Strobe,High cd,Red,Outdoor(includes plastic weatherproof back box) P2WK*t 2-Wire Horn Strobe,Standard cd,White,Outdoor(includes plastic weatherproof back box) P2WHK*t 2-Wire Horn Strobe,High cd,White,Outdoor(includes plastic weatherproof back box) P4RKt 4-Wire Horn Strobe,Standard cd,Red,Outdoor(includes plastic weatherproof back box) P4WK 4-Wire Horn Strobe,Standard cd,White,Outdoor(includes plastic weatherproof back box) P2RHK-120 2-Wire Horn Strobe,High cd,Red,Outdoor,120 V(includes plastic weatherproof back box) Wall Strobes SRK*t Strobe,Standard cd,Red,Outdoor(includes plastic weatherproof back box) SRHK*t Strobe,High cd,Red,Outdoor(includes plastic weatherproof back box) SWK*t Strobe,Standard cd,White,Outdoor(includes plastic weatherproof back box) SWHK*t Strobe,High cd,White,Outdoor(includes plastic weatherproof back box) Horns HRKt Horn,Red,Outdoor(includes plastic weatherproof back box) Accessories SA-WBB Red,Metal Weatherproof Back Box SA-WBBW White,Metal Weatherproof Back Box Notes: *Add"-P"to model number for plain housing(no"FIRE"marking on cover),e.g.,P2RK-R t Add%R"to model number for weatherproof replacement device(no back box included),only for use with weatherproof outdoor flush mounting plate,WTP and WTPW. "Standard cd"refers to strobes that include 15,15/75.30,75,95,110,and 115 candela settings."High cd"refers to strobes that include 135,150,177,and 185 candela settings.When replacing standard outdoor units both the device and back box must be replaced. SYSTEM ©t to c System Sensor. SENSOR° 3625 Ohio Avenue•St.Charles,IL 60174 Pfoductsptprod product information, tochanpevnhoutestcersion sthisdatasheet. Phone:800-SENSOR2•Fax:630-377-6495 or current product informal on,including th3/12 latest version of his data sheet. AVD501201•3/12 SYSTEM SENSOR® Indoor Selectable- i Output Strobes and Horn Strobes for =� Ceiling Applications - 'fig ..°1 l System Sensor L-Series audible visible notification products are rich with features guaranteed to cut installation times and maximize profits with lower _ current draw and modern aesthetics. �'l1 Features The System Sensor L-Series offers the most versatile and • Plug-in design with minimal intrusion into the back box easy-to-use line of horns,strobes,and horn strobes in the industry with lower current draws and modern aesthetics.With white and red • Tamper-resistant construction plastic housings,wall and ceiling mounting options,System Sensor • Automatic selection of 12-or 24-volt operation L-Series can meet virtually any application requirement. at 15 and 30 candela • Field-selectable candela settings on ceiling units: The entire L-Series product line of ceiling-mount strobes and horn 15,30,75,95, 115, 150,and 177 strobes include a variety of features that increase their application versatility while simplifying installation.All devices feature a plug-in • Horn rated at 88+dBA at 16 volts design with minimal intrusion into the back box,making installations • Rotary switch for horn tone and two volume selections fast and foolproof while virtually eliminating costly and time- • Universal mounting plate for ceiling units consuming ground faults. • Mounting plate shorting spring feature checks wiring continuity To further simplify installation,the L-Series utilizes a universal before device installation mounting plate so installers can mount them to a wide array of back • Electrically Compatible with legacy SpectrAlert and SpectrAlert boxes.With an onboard shorting spring,installers can test wiring Advance devices continuity before the device is installed. • Compatible with MDL3 sync module Installers can also easily adapt devices to a suit a wide range of • Listed for ceiling mounting only application requirements using field-selectable candela settings, automatic selection of 12-or 24-volt operation,and a rotary switch for horn tones with two volume selections. Agency Listings Sicxauxc & LISTED APPROVED S5512 FM approved except 7125-1653.05D4 S4011 for ALERT models 7135-1653:0503 3057383 AVOS868-02•12/01/2017•Page 3 L-Series Specifications Arch itect/Engi neer Specifications General L-Series ceiling-mount strobes and horn strobes shall mount to a standard 4 x 4 x 1'/2-inch back box,4-inch octagon back box,or double- gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 17/8-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,L-Series products,when used with the Sync•Circuit-Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module,12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts.Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Ceiling strobes and horn strobes shall have field-selectable candela settings including 15,30,75,95, 115,150,and 177. Strobe The strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync-Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize L-Series strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 4 11/16 x 4 11/16 x 2 1/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Specifications Operating Temperature 320F to 120OF(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 VDC or regulated 24 DC/FWR' Operating Voltage Range2 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage Range(MDL3) 8.5 to 17.5V(12 V nominal)or 16.5 to 33 V(24V nominal) Input Terminal Wire Gauge 12 to 18 AWG Ceiling-Mount Dimensions(including lens) 6.8"diameter x 2.5"high(173 mm diameter x 64 mm high) Ceiling-Mount Surface Mount Back Box Skirt Dimensions 6.9"diameter x 3.4"high(175 mm diameter x 86 mm high) (SBBCRL,SBBCWL) Notes: 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products will operate at 12 V nominal only for 15 and 30 cd. AVOS868-02.12/01/2017-Page 2 � r 1��r UL Current Draw Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-17.5 V0lts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC DC FWR Sound Pattern dB DC DC FWR Candela 15 87 41 60 Temporal High 39 44 54 Range 30 153 63 86 Temporal Low 28 32 54 75 N/A 111 142 Non-Temporal High 43 47 54 95 N/A 134 164 Non-Temporal Low 29 32 54 115 N/A 158 191 3.1 KHz Temporal High 39 41 54 150 N/A 189 228 3.1 KHz Temporal Low 29 32 54 177 N/A 226 264 3.1 KHz Non-Temporal High 42 43 54 3.1 KHz Non-Temporal Low 28 29 54 Coded High 43 47 54 3.1 KHz Coded High 42 43 54 UL Max.Current • Range 8-17.5 Volts 16-33 Volts DC Input 15cd 30cd 15cd 30cd 75cd 95cd 115cd 150cd 177cd Temporal High 103 167 71 90 143 165 187 217 254 Temporal Low 96 165 54 71 137 161 185 211 249 Non-Temporal High 106 173 71 90 141 165 187 230 273 Non-Temportal Low 95 166 54 71 124 161 170 216 258 3.1 K Temporal High 111 164 69 94 147 163 184 229 257 3.1 K Temporal Low 103 163 54 88 143 155 185 212 252 3.1 K Non-Temporal High 111 172 69 94 144 164 202 229 271 3.1K Non-Temporal Low 103 169 54 88 131 155 187 217 259 16-33 Volts FWR Input 15cd 30cd 75cd 95cd 115cd 150cd 177cd Temporal High 107 135 179 198 223 254 286 Temporal Low 78 101 151 172 199 229 262 Non-Temporal High 107 135 179 198 223 254 286 Non-Temportal Low 78 101 151 172 199 229 262 3.1 K Temporal High 108 135 179 200 225 255 289 3.1 K Temporal Low 79 101 150 171 196 229 260 3.1 K Non-Temporal High 108 135 179 200 225 255 289 3.1 K Non-Temporal Low 79 101 150 171 196 229 260 Horn Strobe Tones and Sound Output Data StrobeHorn • .: 8-17.5 16-33 Switch Volts Volts Position Sound Pattern dB DC DC FWR 1 Temporal High 84 89 89 2 Temporal Low 75 83 83 3 Non-Temporal High 85 90 90 4 Non-Temporal Low 76 84 84 5 3.1 KHz Temporal High 83 88 88 6 3.1 KHz Temporal Low 76 82 82 7 3.1 KHz Non-Temporal High 84 89 89 8 3.1 KHz Non-Temporal Low 77 83 83 AVDS868-02.12/01/2017•Page 3 L-Series Dimensions 2.47°(62.7 mm) 1.37°(34.8 mm) 6.92°diam. 2.5° 6.83°diam. (175.77 mm) (64 mm) (173 mm) yr.o*ru.r O�� O TR O o O o 0 O ®O O o Q o 0 A0545-00 A0546-00 Ceiling-Mount Horn Strobes Ceiling Surface Mount Back Box 1 � C m ® O F§ �pc��trrt Will �t iilri A0494-01 A0531-01 2-Wire Ceiling Mount Horn Strobes 4-Wire Ceiling Mount Horn Strobes with Ceiling Surface Mount Back Box with Ceiling Surface Mount Back Box L-Series Ordering Information Model Description Model Description Ceiling Horn Strobes Ceiling Strobes PC2RL 2-Wire,Horn Strobe,Red SGRL Strobe,Red PC2WL 2-Wire,Horn Strobe,White SCWL Strobe,White PC4RL 4-Wire,Horn Strobe,Red SCWL-CLR-ALERT Strobe,White,ALERT PC4WL '4-Wire,Horn Strobe,White Accessories TRC-2 Universal Ceiling Trim Ring Red TRC-2W Universal Ceiling Trim Ring White SBBCRL Ceiling Surface Mount Back Box,Red SBBCWL Ceiling Surface Mount Back Box,White For a ceiling-listed horn-only device,see AVDS865"Indoor Selectable- Output Horns,Strobes,and Horn Strobes for Wall Applications". SYSTEM m2017 System Sensor. 3825 Ohio Avenue•St.Charles, IL 60174 Product specifications subject tochange without notice.Visit systemsensorcom SENSORo Phone:800-SENSOR2•Fax:630-377-6495 for current product Information,AVDS868-02- 2/latest 1/2017esbnof hisdata sheet. AVDS866-02.1 2/0112 0 1 7 A SYSTEM - - ; _ _ SENSOR® Indoor Selectable- Output Horns Strobes, and Horn Strobes for Wall Applications � t System Sensor L-Series audible visible notification - products are rich with features guaranteed to cut C-. ; installation times and maximize profits with lower current draw and modern aesthetics. Features .._ _ _ - - -" • Updated Modern Aesthetics The System Sensor L-Series offers the most versatile and • Small profile devices for Horns and Horn Strobes easy-to-use line of horns,strobes,and horn strobes in the industry • Plug-in design with minimal intrusion into the back box with lower current draws and modern aesthetics.With white and red plastic housings,standard and compact devices,and plain,FIRE, • Tamper-resistant construction and FUEGO-printed devices,System Sensor L-Series can • Automatic selection of 12-or 24-volt operation at 15 and 30 meet virtually any application requirement. candela • Field-selectable candela settings on wall units: The L-Series line of wall-mount horns,strobes,and horn strobes 15,30,75,95, 110, 135,and 185 include a variety of features that increase their application versatility • Horn rated at 88+dBA at 16 volts while simplifying installation.All devices feature plug-in designs • Rotary switch for horn tone and two volume selections with minimal intrusion into the back box,making installations fast and foolproof while virtually eliminating costly and time-consuming • Mounting plate for all standard and all compact wall units ground faults. • Mounting plate shorting spring checks wiring continuity before device installation To further simplify installation and protect devices from construction • Electrically compatible with legacy SpectrAlert and SpectrAlert damage,the L-Series utilizes a universal mounting plate for all Advance devices models with an onboard shorting spring,so installers can test wiring • Compatible with MDL3 sync module continuity before the device is installed. • Strobes and Horn Strobes listed for wall mounting only Installers can also easily adapt devices to a suit a wide range • Horns listed for wall or ceiling use of application requirements using field-selectable candela settings, automatic selection of 12-or 24-volt operation,and a rotary switch Agency Listings for horn tones with two volume selections. SIGNALING O F M 0 LISTED APPROVED S5512 FM approved except 7125-1653:0504 S4011 for ALERT models 7135-1653A503 3057383.3057072 AVDS865-05.2/22/2018-Page 1 L-Series Specifications Architect/Engineer Specifications General L-Series standard horns,strobes,and horn strobes shall mount to a standard 2 x 4 x 17/8-inch back box,4 x 4 x 11/2-inch back box,4-inch octagon back box,or double-gang back box.L-Series compact products shall mount to a single-gang 2 x 4 x 1 7/8-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products for all standard models and a separate universal mounting plate shall be used for mounting wall compact models.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,L-Series products,when used with the Sync•Circuit`'Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module,12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts.Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15,30,75,95,110,135,and 185, Strobe The strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service.The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize Strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 411/16 x 411/18 x 21/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC or regulated 24 DC/FWR1 Operating Voltage Range 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(including lens) 5.6-L x 4.7"W x 1.91-D(143 mm L x 119 mm W x 49 mm D) Compact Wall-Mount Dimensions(including lens) 5.26"L x 3.46"W x 1.91"D(133 mm L x 88 mm W x 49 mm D) Horn Dimensions 5.6"L x 4.7"W x 1.25-D(143 mm L x 119 mm W x 32 mm D) Compact Horn Dimensions 5.25"L x 3.45"W x 1.25"D(133 mm L x 88 mm W x 32 mm D) 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.Strobe products will operate at 12 V nominal only for 15 cd and 30 cd. AVDS865-05.2/2 212 0 1 8•Page 2 w \ UL Current Draw Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC DC FWR Sound Pattem dB DC DC FWR Candela 15 88 43 60 Temporal High 39 44 54 Range 30 143 63 83 Temporal Low 28 32 54 75 N/A 107 136 Non-Temporal High 43 47 54 95 N/A 121 155 Non-Temporal Low 29 32 54 110 N/A 148 179 3.1 KHz Temporal High 39 41 54 135 N/A 172 209 3.1 KHz Temporal Low 29 32 54 185 N/A 222 257 3.1 KHz Non-Temporal High 42 43 54 3.1 KHz Non-Temporal Low 28 29 54 Coded High 43 47 54 3.1 KHz Coded High 42 43 54 UL Max.Current Draw(mA RMS),Wall Horn Strobe,Candela Range(15-185 cd) 8-17.5 Volts 16-33 Volts DC Input 15cd 30cd 15cd 30cd 75cd 95cd 110cd 135cd 185cd Temporal High 98 158 54 74 121 142 162 196 245 Temporal Low 93 154 44 65 111 133 157 184 235 Non-Temporal High 106 166 73 94 139 160 182 211 262 Non-Temportal Low 93 156 51 71 119 139 162 190 239 3.1 K Temporal High 93 156 53 73 119 140 164 190 242 3.1 K Temporal Low 91 154 45 66 112 133 160 185 235 3.1K Non-Temporal High 99 162 69 90 135 157 175 208 261 3.1 K Non-Temporal Low 93 156 52 72 119 138 162 192 242 16-33 Volts FWR Input 15cd 30cd 75cd 95cd 110cd 135cd 185cd Temporal High 83 107 156 177 198 234 287 Temporal Low 68 91 145 165 185 223 271 Non-Temporal High 111 135 185 207 230 264 316 Non-Temportal Low 79 104 157 175 197 235 283 3.1 K Temporal High 81 105 155 177 196 234 284 3.1 K Temporal Low 68 90 145 166 186 222 276 3.11K Non-Temporal High 104 131 177 204 230 264 326 3.1 K Non-Temporal Low 77 102 156 177 199 234 291 Horn Tones and Sound Output Data StrobeHorn and Horn • .: 8-17.5 16-33 Switch Volts Volts Position Sound Pattern dB DC DC FWR 1 Temporal High 84 89 89 2 Temporal Low 75 83 83 3 Non-Temporal High 85 90 90 4 Non-Temporal Low 76 84 84 5 3.1 KHz Temporal High 83 88 88 6 3.1 KHz Temporal Low 76 82 82 7 3.1 KHz Non-Temporal High 84 89 89 8 3.1 KHz Non-Temporal Low 77 83 83 9* Coded High 85 90 90 10* 3.1 KHz Coded High 84 89 89 Settings 9 and 10 are not available on 2-wire horn strobes.Temporal coding must be provided by the NAC.If the NAC voltage is held constant,the horn output remains constantly on. AVDS865-05•2/22/2018•Page 3 L-Series Dimensions 191° 3.46° 3A6° 48.5 mm Be mm - - 32 3 155° 125 88 mm 125° I 32 mm (9.1 c a m) (3.9 cm) 32 mm 0 0 F � o 5271 .p 1 4 5.38° 133.9 mm 527' ��p1p 1p (13.7 cm) O 133.9 mm plp/p/p/l/p ao 1 /1/1�1,1,1 O 1IS 1 11 LL— A054B-00 A0547-00 A0557-00 Compact Strobe,Horn Strobe Compact Horn Compact Wall Surface Mount Back Box SBBGRL,SBBGWL 4.78" (11.94 em) 1.91° 4.7° 125, (4.65 cm) 119 mm 32 mm (12.24 cm) 1.9. 1.25" (4.69 cm) (3.16 mm) � p o ® o 5.67" .11 6.67" p 1ppp' 5.78° O (14.4 cm) LJ 144 mm 74.68 cm) 1i1i�i icy 0 0 A0550-00 A0549-00 A0554-01 Strobe,Horn Strobe Horn Wall Surface Mount Back Box SBBRUSBBWL L-Series Ordering Information DescriptionModel Description Model Wall Horn Strobes Horns* P2RL 2-Wire,Horn Strobe,Red HRL* Horn,Red P2WL 2-Wire,Horn Strobe,White HWL* Horn,White P2GRL 2-Wire,Compact Horn Strobe,Red HGRL* Compact Horn,Red P2GWL 2-Wire,Comp 2 fils act Horn Strobe,White HGWL* Compact Horn,White P2RL-P 2-Wire,Horn Strobe,Red,Plain Accessories P2WL-P 2-Wire,Horn Strobe,White,Plain TR-2 Universal Wall Trim Ring Red P2RL-SP 2-Wire,Horn Strobe,Red,FUEGO TR-2W Universal Wall Trim Ring White P2WL-SP 2-Wire,Horn Strobe,White,FUEGO SBBRL Wall Surface Mount Back Box,Red P4RL 4-Wire,Horn Strobe,Red SBBWL Wall Surface Mount Back Box,White P4WL 4-Wire,Horn Strobe,White SBBGRL Compact Wall Surface Mount Back Box,Red Wall Strobes SBBGWL Compact Wall Surface Mount Back Box,White SRL Strobe,Red SWL Strobe,White SGRL Compact Strobe,Red SGWL Compact Strobe,White SRL-P Strobe,Red,Plain SWL-P Strobe,White,Plain SRL-SP Strobe,Red,FUEGO SWL-CLR-ALERT Strobe,White,ALERT Notes: All-P models have a plain housing(no"FIRE"marking on cover). All-SP models have"FUEGO"marking on cover. All-ALERT models have"ALERT'marking on cover. *Horn-only models are listed for wall or ceiling use. SYSTEM 3825 Ohio Avenue•St.Charles,IL 60174 ©2018 System Sensor. SENSOR Phone:800SENSOR2•Fax:630-377-6495 Product rcurrespecifications ductiintonactto change ngtheltestwrionofthisdatasarcom heet. for current product intonation,including the latest version of this date sheet. www.systemsensor.com AVDS865-05.2/22/2018 6820EVS Intelligent Fire Alarm Control Panel with Emergency Voice System The 6820EVS panels and accessories provide features to meet the requirements for Mass Notification Systems as described in UL 2572 2nd Edition and UL 86410th Edition. The 6820EVS is an intelligent addressable Fire Alarm Control Panel combined with an Emergency Voice System(EVS)and are direct replacements for the 5820XL-EVS FACP. When the EVS features are enabled,they are integrated with the fire alarm and voice evacuation functions of the control panel. The emergencyvoice system operations include an onboard supervised microphone.All-call and non-active call buttons can quickly select all active or non-active output groups.The system also allows for emergency messages overfire. The 6820EVS FACP has one built-in signaling line circuit(SLC),which can support 159 SK detectors and 159 SK modules,or 127 SD protocol devices.Additional SLC loops can be added for a maximum of 1110(SK)or 635(SD)points per panel. The built-in digital alarm communicator/transmitter(DACT)is dualtechnology,IP and POTS.The POTS transmits system status(alarms,troubles,AC loss,etc.)to a Central Station via the public switched telephone network.The IP communicator's internet monitoring capability sends alarm signals overthe Internet saving the monthly cost of two dedicated business telephone lines.Although not required,the secondary telephone line may be retained providing backup communication overthe public switched telephone line.Optional cellular reporting is available. The 6820EVS has six onboard Flexput°circuits that can be configured as notification outputs or auxiliary power.The 6820EVS also has a form-C trouble relay,and two programmable form-C relays,along with powerful features such as drift compensation,pre- trouble maintenance alert,a built-in sensortest to complywith NFPA 72 calibration testing requirements,and a calibration trouble alert. A common communications and annunciation link allows up to 17 panels to be connected via copper or fiber optic cable.A designated panel is configured as the communicator for all panels in the link for convenient single-point communications. FEATURES AND BENEFITS • Single enclosure for both fire and • Selectable strobe synchronization for • Two programmable relays and one fixed emergency voice components Amseco°,System Sensor®,Wheelock',and trouble relay • Ability to select EVS messages as priority Gentex°devices • Compatible with SWIFT°wireless devices over fire • Built-in DACT with IP and optional cellular • Convenient field-upgradeable firmware • 15 Recordable one-minute messages that reporting • Network support for up to 17 sites can be mapped to eight EVS buttons • Built-in USB interface for quick and easy • Network card allows copper network • Capable of producing 520 Hztones to meet programming connection with a multi-mode or single- NFPA 72 requirements • JumpStartl auto programming reduces mode fiber connection - • Support for up to 4 LOC consoles and 8 installation time • Real-time clock/calendar with automatic addressable amplifiers • 999 software zones&999 output groups daylight savings control • Expandable SLC loops to 1110(SK)or 635 for flexible design options • History file with 1,000 event capacity (SD)point capacity • 23 preset notification cadence patterns • Six Flexput circuits for NAC outputs or (including ANSI°3.41) auxiliary power • Allows up to 24 SBUS devices • Four programmable function keys. Honeywell SILENT' KNIGHT USER INTERFACE SK COMPATIBLE ADDRESSABLE DEVICES LED INDICATORS Note:SKand SD devices cannot be mixed in the same fire alarm system. • General Alarm(Red) • Supervisory(Yellow) SK-ACCLIMATE:Multi criteria photoelectric smoke detectorwith • System Trouble(Yellow) thermal135o Ffixedtemperature • System Silenced(Yellow SK-BEAM:Reflected beam smoke detector without test feature • System Power(Green) SK-BEAM-T-.Reflected beam smoke detector with test feature KEYPAD OSI-RI-SK:Reflected beam smoke detector,SK protocol • 12-key numeric pad SK-CONTROL:Supervised control module • Acknowledge SK-CONTROL-6:Six circuit supervised control module • Alarm Silence SK-DUCT:Photoelectric duct smoke detector with extended air • System Reset speed range • Drill SK-FIRE-CO:Four criteria fire and carbon monoxide detector • Fl-F4 Programmable Function Keys SK-FIRE-CO-W:Four criteria fire and carbon monoxide detector, white PROGRAMMING SK-HEAT:Fixed thermal detector(135°F) The 6820EVS system offers several options to simplify and expedite SK-HEAT-W:Fixed thermal detector(1350F),white programming.JumpStart°auto programming minimizes SK-HEAT-ROR:Fixed rate of rise detector programming required to start a new system.The built-in keypad,or the remote annunciators give on-site access to current system SK-HEAT-HT:Fixed high temperature heat detector(190°F) programming.System programming can also be accomplished SK-HEAT-HT-W:Fixed high temperature heat detector(1901F), using the Windows®-based Honeywell Fire Software Suite(HFSS). white ORDERING INFORMATION SK-HEAT-ROR-W:Fixed rate of rise detector,white 6820EVS:Addressable fire alarm control panelwith emergency SK-ISO:Fault isolator module voice system,red SK-MINIMON:Mini monitor module COMPATIBLE EVS EQUIPMENT SK-MONITOR:Monitor module EVS-50W:50 Watt amplifier SK-MONITOR-2:Dual input monitor module EVS-125W:125 Watt amplifier SK-MON-10:10-input monitor module EVS-10OW:50/100 Watt amplifier SK-PHOTO:Photoelectric smoke detector EVS-10OWBU:External backup amplifier SK-PHOTO-W:Photoelectric smoke detector,white EVS-INT50W:50/Watt internal amplifier SK-PHOTO-R:Photoelectric detector with remote test capability EVS-CE4:Provides 4 additional audio circuits SK-PHOTO-R-W:Photoelectric detectorwith remote test capability, white EVS-RVM:Remote voice module EVS-SW24:24 switch expander SK-PHOTO-T:Photoelectric smoke detector with fixed heat(135°F) SK-PHOTO-T-W:Photoelectric smoke detectorwith fixed thermal EVS-VCM:Network voice control module heat(1351F),white EVS-LOC:Local operator console SK-PTIR-W:Multi criteria photoelectric smoke detectorwith thermal COMPATIBLE SBUS DEVICES 135°F fixed temperature,white 6860:4x40 LCD remote fire annunciator with four programmable SK-PULL-SA Addressable single action pull station buttons,red SK-PULL-DA:Addressable dual action pull station 5860:4x20 LCD remote fire annunciator,gray SK-RELAY:Addressable relay module 586OR:4x20 LCD remote fire annunciator,red SK-RELAY-6:Addressable Six relay control module 6855:420 LCD remote fire annunciator,red SK-RELAYMON-2:Addressable Dual relay/monitor module 5865-3:LED annunciators-display up to 30 LEDs(15 red/15 SK-ZONE:Addressable zone interface module yellow) SK-ZONE-6:Six zone interface module 5865-4:LED annunciators-display up to 30 LEDs(15 red/15 yellow).Keyswitches forsilence and reset,and a system trouble LED 5880:LED 1/0 module with 40 programmable LED outputs and eight supervised dry contact inputs 5883:Relay interface.Provides 10 Form C relays 5824:Seria VParallel printer interface module for printer connection Page 2 of 4—351606:E•3/7/2022 Aqw"`^ SK BASES SYSTEM EXPANDERS B21OLP:6"mounting base 6815:SLC Expander for IDP or SK devices B501:4'Flangeless mounting base 5815XL:SLC expander for SD devices B20OS:Intelligent sounder base RPS-1000:6A power supply with 6 Flexput circuits&2 Form C B20OS-LF:Low-frequency intelligent sounder base relays B224RB:Relay base 5496:6 amp NAC power expander with 4 power-limited output ckts B224B1:Isolator base OPTIONAL COMMUNICATORS SD COMPATIBLE ADDRESSABLE DEVICES CELL-CAB-SK:Cellular communicator,metal enclosure w/lock& Note:SK and SD devices cannot be mixed in the same fire alarm key system. CELL-MOD:Cellular communicator,plastic enclosure IPGSM-4G:Dual path fire alarm communicator,cellular and/or IP SD505-6AB:Addressable 6'base (primary or backup,selectable) SD505-6113:Addressable 6"short circuit isolator base SK-IP-2:Remote reporting via the Internet.Requires a ViSorALARM° SD505-6RB:Addressable 6"relay base receiver at the central station SD505-6SB:Addressable 6'sounder base MISCELLANEOUS ACCESSORIES SD500-AIM:Addressable input module(switch input) SK-NIC:Network Interface Card.Provides a common SD500-ANM:Addressable notification module communications link forthe IFP-300 SD500-ARM:Addressable relay module SK-NIC-KIT:Installation Accessory Kit SD505-DTS-K:Remote test switch/LED indicator for the SK-FML:Fiber-Optic Multi Mode,transmitter and receiver SD505-DUCTR SK-FSL:Fiber-Optic Single Mode SD505-DUCT:Addressable Duct Smoke Detector RBB:Remote battery box accessory cabinet SD505-DUCTR:Addressable Duct Detector housing with relay base SK-SCK:Seismic compliance kit used to fasten batteries to the fire SD505-HEAT:Absolute temperature heat detector.Trip point range Panel from 1351F-1501F(0°C-371C) SOFTWARE SOLUTIONS SD500-LIM:Addressable Line isolator module SKST:Silent Knight Selection Tool provides the installer or design SD500-MIM:Addressable Mini input monitor module(switch input) architectwith a Windows'-based software system configuration tool to create a detailed bill of material(BOM)and battery SD505-PHOTO:Photoelectric smoke detector calculations SD500-PS/-PSDA:Addressable Single or dual action pull station HFSS:Honeywell Fire Software Suite provides remote and local SD500-SDM:Addressable smoke detector module panel programming,detector status,event history and additional SWIFT WIRELESS DEVICES data.Databases can be uploaded/downloaded via the panel's USB port using a flash drive.Requires a PC running Microsoft' Note:SWIFT is only compatible with System Sensor(SK)devices.It Windows®. is not compatible with Hochiki(SD)devices. WSK-WGI:Wireless gateway WSK-PHOTO:Wireless photoelectric smoke detectorwith B501W base WSK-PHOTO-T:Wireless photoelectric smoke detectorwith fixed thermal detection(135°F)and 8501W base W-SYNC:Wireless sync module WSK-HEAT:Wireless,fixed heat detector(135°F)with B501W base WSK-HEAT-ROR:Wireless rate-of-rise heat detector and B501W base WSK-MONITOR:Wireless monitor module WSK-RELAY:Wireless relay module WSK-PULL-DA:Wireless pull station WAV-RL,WAV-WL,WAV-CRL,WAV-CWL:Wireless AV bases W-USB:Wireless USB radio/antenna dongle that plugs into the USB port of a PC running SWIFT Tools SWIFT Tools:Programming and diagnostic utility for the wireless gateway and devices.Available for download from www.farenhyt.com 351606:E•3/7/2022 — Page 3 of 4 --arm 6820EVS TECHNICAL SPECIFICATIONS SYSTEM CAPACITY TEMPERATURE AND HUMIDITY Intelligent Signaling Line Circuits:1 RANGES (expandable) This system meets NFPA requirements for Silent Knightt,SWIFT",and System Addressable device capacity:1110(SK)or operation at 0—49°C(32-120°F)and at aSensor" trademarks 635(SD) relative humidity 93%±2%RH(non- of + International condensing)at 32°C±2°C(90°F±3°F). Amseco"is a registered trademark Programmable software zones:999 However,the useful life of the system's of • tter Sitectric Signa[Company, Output circuits:6(expandable) standby batteries and the electronic LLC.Gentex"I is a,registered SBUS devices:24(16 annunciators,8 LED components may be adversely affected by modules) extreme temperature ranges and humidity. trademarkofGentexCorporation. Therefore,it is recommended that this HochikiO is , registered trademark LOC units:4 system and its peripherals be installed in an • • • •. . WheelockO Addressable amplifiers(total watts):8 environment with a normal room is a trademark of Cooper (1000) temperature of 15—27'C/60—80°F Technologies Company.ANSI"is a ELECTRICAL STANDARDS AND CODES registered trademark AC Power:120VAC,60Hz,3.3A The 6820 complies with the following American . Standards Standby Current:190 mA standards and codes: Institute,Inc.VisorALARMO' Alarm Current:250 mA NFPA 72 registered trademark of the Teldat Flexput Circuits:Terminal block provides NFPA13 Corporation. • • • connections for(six Class B orthree Class A) NFPA15 •• registered NACs or auxiliary power.Power-limited, NFPA 16 trademarks of • • ft supervised circuitry.Maximum current per NFPA 70 Corporation. circuit:3 A.Cannot exceed 6A total for all UL 86410th Edition circuits.End-of-line resistor:4.7k ohm,1/2 Thisdocument • to be watt for Class B NACs UL2572 2nd Edition used for installation purposes.We Communication Loop:Supervised and Central station;remote Signaling;Local try to keep our product Information power-limited,Class A or Class B,32VDC, Protective Signaling Systems;Auxiliary up-to-date and accurate.We cannot 150mA Protected Premises Unit;Water Deluge releasing service.Suitable for automatic, applicationscover all specific Two Programmable Relays and One Fixed manual,waterflow,sprinkler supervisory anticipate all requirements.A.I.I. Trouble Relay:Contact ratin 27.4 change VDC(resistive),Form C g 2.5 A C (DACTnnn-coded)signaling services specifications are subjectto Battery:Cabinet holds maximum of two 18 AGENCY LISTINGS AND withoutnotice. AH batteries APPROVALS Country of origin: Battery Charger Capacity:7-35 AH UL Listed: S2766 PHYSICAL CSFM:7165-0559:0500 Dimensions:21.6"W x 28.1"H x 5.1"D FDNY: COA#6249 (54.9cm W x 71.4cm H x 13.Ocm D) FM:Approved Weight:50 lbs.(22.7 kg.) Seismic:(CA)VMA-45894-05C: Color:Red Honeywell Silent Knight 12 Clintonville Road Northford,CT06472-1610 Honeywell 203.484.7161 351606 1 E 1 04/22 ®Sn,,�' www.sitentknight.com ©2022 Honeywell International Inc NMGHT 5860/586OR Remote Annunciator The 5860/R operates and programs Silent Knight°fire alarm control panels (FACPs).The 5860/R's keypad and display match the built- in annunciator of the FACP. .y , .a , The remote annunciator connects to the control panel via the RS-485 system bus.When the ® " ' system is in normal operation and has AC power,the Power LED is lit and all other LEDs are " off.The other LEDs turn on as alarms,supervisories,troubles,system silenced,and AC power losses occur. INSTALLATION The 5860/R can be surface orflush mounted.Use the optionaltrim ring forsurface mounts. When flush mounting,an electrical box is optional.If using an electrical box,use a 4S, single-gang,or double-gang box. COMPATIBILITY The 5860/R is compatible with the following Silent Knight FACPs: • 6820/6820EVS • 6808 • 6700 • 5820XL/5820XL-EVS • 5808 • 5700 FEATURES AND BENEFITS • UL listed.Complies with UL 864,loth • Initiate and end fire drills with a single key • Available in red or gray color Edition;UL 2572,2nd Edition;and NFPA 72 press • Accepts user codes or fire fighter's key • 80-character backlit LCD display(4 lines • View current status by alarms, • Support for simultaneous use of multiple with 20 characters on each line) supervisories,or troubles 5860/Rs • Tactile/audible feedback • On-board piezo sounder audibly indicates • Wiring lengths up to 6000 ft.(1.83 km)from • RS-485 SBUS interface to panel alarms,troubles,and supervisories the FACP • Larger keypad buttons for system reset and • Five status LEDs for;alarms,supervisory, silence trouble,silence and AC power indications Honeywell SHINY WQGHT 1 5860/586OR TECHNICAL SPECIFICATIONS PHYSICAL ORDERING INFORMATION v re Dimensions:9.1"W x 7.4"H x 1.5"D 5860R:Red four line LCD Remote ' (23.1 cm W x 18.8 cm H x3.8 cm D) Annunciatorwith 20 characters per line. istered trademarks ' Honeywell International, Shipping Weight:2.8 lbs(1.3 kg) 5860:Gray four line LCD Remote Color:Red or Gray Annunciatorwith 20 characters per line. This document is not intended ENVIRONMENTAL OPTIONAL ACCESSORIES used for , „ . 5860TR:Red Trim Ring for surface try to keep our product information Operating Temperature:32°Fto 120°F mounting. (0°C to 49°C) 5860TG:Gray Trim Ring for surface cover all specific applicationsor Humidity:10%to 93%relative humidity mounting. anticipate all.requirements.ALL (noncondensing) STANDARDS AND CODES specifications are subjectto change ELECTRICAL notice. The 5860/R complies with the following without Operating Voltage:24 VDC standards/codes: Country of origin:U.S.A. Standby Current:20 mA • UL 864,loth Edition:Standard for Control Alarm Current:25 mA Units for Fire Alarm Systems Maximum Wiring Distance:6,000 ft.(1.83 • UL 2572,2nd Edition:Standard for Mass km)from FACP(depending on wire gauge Notification Systems and number of devices on the SBUS) • NFPA 72:National Fire Alarm and Signaling SYSTEM Code Maximum No.of 5860/Rs per System: AGENCY LISTINGS AND • 8 for 5700 or 6700 APPROVALS • 12 for 5808 or 6808 • UL Listed • 16 for 5820XL/EVS or 6820/EVS • FDNY-COA(TBD) Honeywell Silent Knight 12 Clintonville Road Northford,CT06472-1610 Honeywell 203.484.7161 350224 1 1 1 11/21 SKENT' www.si[entknight.com ©2021 Honeywell International Inc. 13 MGHT • tarLnFire, . Commercial Fire Alarm Cellular Wor IP COMMERCIAL FIRE CELLULAR LTE Communicators Fire Alarm I . • Universal full event sole&dual path cellular&/or IP UL and NFPA 72 Fire Code-Compliant,the Starl-ink commercial fire alarm reporting from any panel brand, Series Wireless Commercial Fire Alarm Sole Path&Dual virtually anywhere Path Communicators provide universal support for any brand 12V to 24V fire alarm control panel,reporting in • Code-compliant,replaces 2POTs lines per FACP saves Contact ID and 4/2. With broadest Verizon LTE coverage thousands of dollars per year over the leased landlines footprint available,via most extensively deployed LTE CAT1, • Supports 12V-24 control panels and FACPs that using proven StarLink circuitry,they are also available communicate using Contact ID and 4/2(such as on legacy in mercantile locking metal models.All provide the most panels),as primary or backup economical solution for easy,versatile installation.Also regional compliances,i.e.,CSFM,NYCFD,LAFD and more. • Full data Reporting to any Central Station nationwide, via Verizon®LTE Network,'The Nations largest and most Easy,Universal Installation at Every Application;Panel- reliable LTE network.Rated#1 overall network,proven to Powered Technologr.StarLink Fire Communications are deliver consistently fast speeds ad i more places than any easily connected to any panel or Fire Alarm Control Panel (FACP)standardly operating between 12V and 24V.Flexible other network"t in any application,Starl-ink Fire also comes in standard,or • Communicate critical life and safety alarm reports on Mercantile Models in metal housings,with code-compliant LTE(Long Term Evolution)10+year life,cyber-protected supervision,and choice of power options,Panel-Powered multi-billion dollar cellular network,for maximum life Technology(powered by the panel),or direct-connect safety&liability protection 120VAC models.Signal Boost circuitry&dual diversity antennae for maximum signal acquisition&null avoidance, • Easiest installation,powered by panel,NO extra power receiving signals simultaneously on both antennae. supply,NO conduit,self supervised on 4 wires Flexible Performance&Reporting Options.Starl-ink • Over-the-Air Upgradeable Communicator Firmware. Fire provides full data reporting,in sole and dual path,as Remote ability for critical/mandatory updates,without a a primary or backup,to any central station of your choice, truck-roll without requiring any special equipment on premises. • Ultra-affordable plans are available to meet various codes Cost-saving models and plans for any code requirement. and requirements,with supervisory check-ins from 200 Substantial savings over monthly dedicated landline charges. seconds,to 5 minutes,to an hour.The units are very easily And,$100 saving incentive for system upgrades from old activated,plans and options are selected,and 24/7 account radios(all makes)and old POTS landlines,as well as new management is provided all through www.napcocomnetcom. installations connected by Napco StarLink Universal Tire Alarm verizon✓ Communicators • Sole Path Cellular and Dual Path Cellular&/or IP Models • Choice of plans(varies by model)-check-ins from 200 seconds,to 5-minutes to 1 hour,Verizon LTE Network • Patented Signal Boost1mand Dual Diversity Antennae for maximum signal acquisition&null avoidance, receiving signals simultaneously on both antennae • Money-saving Tradeup incentive credit • Bonus:Full High-Speed Napco Panel remote uploading/downloading • COMPLIANCES:NFPA72 Editions:2016,2013,2010, 2007;UL 864,9th Ed.,UL1610,UL985,UL1023,NYCFD; CSFM;LAFD Star"",'nk i j70 . NFPA Code-compliant standard or mercantile metal models(right and left,respectively). tar In Fir Commercial,Fire Alarm Cellular Wor IP COMMERCIAL FIRE CELLULAR&IP 'Fire Alarm LTE Communicators StarLink Fire Specifications Ordering Information STANDARD MODELS: COMMERCIAL FIRE SOLE PATH CELLULAR& • Advanced LTE Dual Diversity Antennae for optimized DUAL PATH CELLULAR&/OR IP("I"MODELS):* performance SLE-LTEVI-FIRE Dual Path Communicator,Cellular&/or IP, • Durable ABS plastic housing includes three keyhole slots for connected by Verizon LTE",ABS. Low current draw,panel- mounting(for commercial application,aligns with triple gang powered technology'(powered by control panel) boxes) SLE-LTEV-FIRE as above,but sole path cellular model • Panel Powered Technology'(powered by panel),Low current SLELTEVI-CFB Commercial Fire Dual Path Mercantile model draw,71 mAstandby,200mA transmit in red metal housing on LTE,Verizon LTE Network,powered • Dimensions:5-3/8"x 7-7/8"x 1-7/8"(HxWxD) directly from control panel • Weight:13.5 oz SLETEVI-CFB-PS Commercial Fire Dual Path Mercantile model • 3 LED Indicators-Green,Signal Strength;Amber-Busy/ in red metal housing,LTE,Verizon LTE Network.Direct 120VAC Activation;Red-Trouble Powered(w/provisions for backup battery/charger).Or, • Patented Signal BoostTm signal amplification circuit and high- Optional TRF12 plug-in transformer may be used,where codes gain performance antennae permit • Operating Environment:0 to 490 C 32-120° ° �=p g ( F),up to 93/a ACCESSORIES: humidity(non-condensing) Free Commercial Fire Tradeup Trifold • 12V-24V Universal FACP Support,auto-current sensing. Brochures/Mailers/Stuffers(A720)for new r Support all brands communicating in Contact ID and 4/2 and existing fire accounts SLE-ANTEXT75 Optional extended antenna with„ 611®. MERCANTILE MODELS(similar to above,with): 75'cable(new conical shape) • Locking Metal Enclosure with Hinged door& 2 key-slots for SLE-ANTEXT50 As above,with 50'cable wall mounting(LED indicators,inside) SLE-ANTEXT30 As above,with 30'cable • Dimensions: 9-5/8"x 11-3/4"x3-3/8"D(HxWxD) SLE-DLEXT Optional,as above,for downloading,extends distance • Weight:8 Ibs(max.,power supply models) to Napco panel up to 100' • Electrical Ratings for 120VAC,60Hz TRF12 Optional Plug in AC Transformer,16.5V/20VA(use is • For Models with Power Supply: subject to local code compliance) • Input Voltage: 120VAC Nominal SLE-DLCBL Optional High-Speed Napco Panel Up/download cable • Input Current:400mA maximum • Maximum Charging Current: 200mA • Electrical Ratings for+12V New! Firel-MIC Integrated Fire Alarm Control • For Models without Power supply: Panel w/StarLink Fire LTE Built In • Input Voltage: 11-15VDC(power-limited output from listed s _. F Award Winning FL-FACP-LTEVS control panel) esx Firewolf 8 Zone 24V Conventional • Input Current:71 mA with peak RF transmission current of ! 101e Commercial Fire Alarm Control 200mA Panel with onboard StarLink Fire® +` Sole Path,Verizon LTE Cellular • Electrical Ratings for the IN 1 Burg/Fire Input: Alarm Communicator and integral menu-driven LCID annunciator,w/ • Input Voltage:9-15VDC ( 4amp,24V power supply.Optionally • Maximum Input Current:U to 2mA from FACP NAC circuit i expandable up to ss points/zones via P P � commercial addressable,wireless or • Electrical Ratings for IN 2 and IN 3' conventional fire devices(2 onboard NACs providing up to 4A notification • Maximum Loop Voltage:15VDC �' power).Locking,mercantile red • Maximum Loop Current: 1.2mA i, enclosure,(surface or flush mount) removable)Vx1J"door with, • Electrical Ratings for 3 PGM Outputs: i 14.25"x16"base:Houses 16Ah battery backup • Open Collector Outputs: Maximum voltage 3V when active; 15V maximum when not active • Maximum PGM Sink Current:SOmA mount V StarUnk Firs a • Operating Environment 0 to 490 C(32-120°F),up to 93% NAPCO humidity(non-condensing) COMMERCIAL FIRE CELLULAR&IP • 12V-24V Universal FACP Supp g ort,auto-current sensing. 333 BayviewAve.,Amityville,NY 11701 USA 16 1-800-645-9445 •Fax:1-631-789-9292 NFPA Support all brands communicating in Contact ID and 4/2 www.napcosecurity.com Startink StarUnk fire,FreUnk SignalB00%Panel-Powered Technologµ Gemini 6 Gemini Commercial are trademarks of Napco.Veruon,LTE,etc are trademak of theirrespeci a companies.'StarUnk offers full data coverage in US from Inrtualyall panel brands reporting in Contact ID or4/2. ForU details on the ShrUnktradeupincen§R see online under hpJAww.raprose *.com/smrfinVsbdink4gupg2de/tPmmosubjeatodiangew/oprriornotice.LTEkfespandaimsarebasedonthoseof tamers NenmrPranWngbasedonMeRooNetricsUSNationalRootSrore®Report 1H2O17. ©NAPCO,NAPCO Security Technologies Inc.(NASDAQ:NSSC) A7342018.9 ECS = 125W SERIES Intelligent 125 Watt Amplifier The ECS-125W is an amplifier compatible with the Farenhyt Emergency Communication System. The ECS-125W is used to amplify audio messages for distribution throughout entire facilities. Since the ECS-125W is designed as a self-contained distributed amplifier,it can be conveniently located near the area of protection to reduce wiring demands.Each ECS- 125W is capable of producing 125-watts of audio power.Up to eight ECS-125W amplifiers can be used on the Emergency Communication System.The ECS-125W has its own power supply with battery backup and includes four speaker circuits which can be expanded to eight speaker circuits when used with the optional ECS-CE4.The ECS-125W is fully supervised by the main panel to identify the trouble conditions. INSTALLATION The ECS-125W Series can be surface-or flush-mounted. COMPATIBILITY The ECS-125W Series is compatible with the following Honeywell Farenhyt Series voice evacuation components: • IFP-300ECS/IFP-300ECSB • IFP-2100ECS/IFP-2100ECSB FEATURES AND'BENEFITS • Complies with UL 86410th Edition and UL • Uses an easy-to-instaltwire harness to • Provides six-wire connection to the ECS 2572 2nd Edition Standards connect the ECS-CE4 audio circuit System: • Meets NFPA 72 standards expander -Two-wires forthevoice bus connections • Provides SBUS addressable to support up • Extends remote installations up to 6,000 -Four-wires for the SBUS connections to eight ECS-125W amplifiers per system feet away from the ECS Series panel • Can be surface-or flush-mounted for a total of 1000 watts • Includes its own power supply and backup . Supports 120 VAC or 240 VAC operation • Each ECS-125W amplifier is supervised battery and has four onboard audio circuits • Selectable for 25V or 70.7V operation expandable to eight with the ECS-CE4 • Available in a red or a black cabinet expander for a system total of 64 audio circuits Honeywell Farenhyt Series ECS-125W SERIES TECHNICAL SPECIFICATIONS PHYSICAL ORDERING INFORMATION Flush Mount Dimensions: ECS-125W:Intelligent 125W Amplifier,red Farenh ytT1 is a trademark,and 14.05"W x 24.75"H x 3.04"D ECS-125WB:Intelligent 125W Amplifier, • = f I registered (36.08 W x 62.09 H x 8.07 D cm) black trademark . neywell Overall Dimensions: ECS-125WHV:High Voltage(240V)125W InternationaL, 16.0"W x 26.25"H x 4.01"D Amplifier (40.06 W x 66.07 H x 10.05 D cm) ACCESSORIES Color:Red or Black Thisdocument ' intended to be ENVIRONMENTAL ECS-CE4:Audio Circuit Expander purposes. RBB:Remote Battery Box accessory try to keep product information Operating Temperature:32°Fto 120°F cabinet.Use for backup batteries up to (0°C to 49°C) 35AH and batteries too large to fit into an ' cannot Humidity:10%to 93%relative humidity ECS-50W cabinet.SK-SCK:Seismic cover all specificapplicaltions, (non-condensing) Compliance Kit antici pate a[[requirements.All ELECTRICAL STANDARDS AND CODES specificationsare • . ctto change The ECS-125W Series complies with the without notice. Module voltage Standby *Alarm following standards and codes. Current Current • UL 864,loth Edition:Standard for Control Units for Fire Alarm Systems Country• • • ECS-125W/B 120V 300mA 2200mA . UL 864,Local Protective Signaling Systems 25V 60 Hz • UL 2572,2nd Edition:Standard for Mass ECS-125WHV 240V 250mA 1250mA Notification Systems 25V 50Hz • UL 1711 • N FPA: *Fully loaded system -NFPA 13 Total Power: -NFPA 70 •Circuit 1:10OW max. -NFPA 72 • Circuit 2-8:50W max. AGENCY LISTINGS AND Main ECS PaneISBUS: APPROVALS Standby Current:10mA • UL Listed:S2766 Alarm Current:10mA • CSFM Approved:7300-0559:0173 Battery Charging Capacity:7—35AH • FDNY:Approved Battery Size:18AH max.allowed in the cabinet.Use the RBB accessory cabinet for larger batteries up to 35AH per system. Voice Integration Wiring: • Six conductor •Two voice bus • FourSBUS THE FUTURE IS Honeywell Fire Solutions WHAT 12 Clintonville Road WE Northford,CT 06472-1610 350772 I G 104-22 MAKE IT 203.484.7161 ©2022 Honeywell International Inc.www.farenhyt.com , Honeywell