HomeMy WebLinkAbout45652-Z �o�g�FF01K�oGy Town of Southold 4/13/2021
P.O.Box 1179
0
o • 53095 Main Rd
Southold,New York 11971
CERTIFICATE OF OCCUPANCY
No: 41949 Date: 4/13/2021
THIS CERTIFIES that the building SOLAR PANEL
Location of Property: 775 Farmveu Rd,Mattituck
SCTM#: 473889 Sec/Block/Lot: 121.-7-5
Subdivision: Filed Map No. Lot No.
conforms substantially to the Application for Building Permit heretofore filed in this office dated
12/21/2020 pursuant to which Building Permit No. 45652 dated 1/7/2021
was issued,and conforms to all of the requirements of the applicable provisions of the law. The occupancy for
which this certificate is issued is:
roof-mounted solar panels as applied for.
The certificate is issued to Maul,George&Morgan
of the aforesaid building.
SUFFOLK COUNTY DEPARTMENT OF HEALTH APPROVAL
ELECTRICAL CERTIFICATE,NO. 45652 2/24/2021
PLUMBERS CERTIFICATION DATED
th i d ignature
o�SUFFna,��, TOWN OF SOUTHOLD
a Gyp BUILDING DEPARTMENT
TOWN CLERK'S OFFICE
�y • SOUTHOLD,'NY
BUILDING PERMIT
(THIS PERMIT MUST BE KEPT ON THE PREMISES
WITH ONE SET OF APPROVED PLANS AND SPECIFICATIONS
UNTIL FULL COMPLETION OF THE WORK AUTHORIZED)
Permit#: 45652 Date: 1/7/2021
Permission is hereby granted to:
Maul, George
2095 Elijahs Ln
Mattituck, NY 11952
To: install roof-mounted solar panels as applied for.
At premises located at:
775 Farmveu Rd, Mattituck
SCTM # 473889
Sec/Block/Lot# 121.-7-5
Pursuant to application dated 12/21/2020 and approved by the Building Inspector.
To expire on 7/9/2022.
Fees:
SOLAR PANELS $50.00
CO-ALTERATION TO DWELLING $50.00
ELECTRIC $100.00
ota $200.00
Buil ing Inspector
Form No.6
TOWN OF SOUTHOLD
BUILDING DEPARTMENT
TOWN HALL
765-1802
APPLICATION FOR CERTIFICATE OF OCCUPANCY
This application must be filled in by typewriter or ink and submitted to the Building Department with the following:
A. For new building or new use:
1. Final survey of property with accurate location of all buildings,property lines, streets,and unusual natural or
topographic features.
2. Final Approval from Health Dept.of water supply and sewerage-disposal (S-9 form).
3. Approval of electrical installation from Board of Fire Underwriters.
4. Sworn statement from plumber certifying that the solder used in system contains less than 2/10 of 1%lead.
5. Commercial building, industrial building,multiple residences and similar buildings and installations, a certificate
of Code Compliance from architect or engineer responsible for the building.
6. Submit Planning Board Approval of completed site plan requirements.
B. For existing buildings(prior to April 9, 1957)non-conforming uses,or buildings and"pre-existing"land uses:
1. Accurate survey of property showing all property lines,streets,building and unusual natural or topographic
features.
2. A properly completed application and consent to inspect signed by the applicant.If a Certificate of Occupancy is
denied,the Building Inspector shall state the reasons therefor in writing to the applicant.
C. Fees
1. Certificate of Occupancy-New dwelling$50.00,Additions to dwelling$50.00,Alterations to dwelling$50.00,
Swimming pool$50.00,Accessory building$50.00,Additions to accessory building$50.00,Businesses$50.00.
2. Certificate of Occupancy on Pre-existing Building- $100.00
3. Copy of Certificate of Occupancy-$.25
4. Updated Certificate of Occupancy- $50.00
5. Temporary Certificate of Occupancy-Residential $15.00,Commercial $15.00
Date.
New Construction: Old or Pre-existing Building: X (check one)
Location of Property: 775 Farmveu Road Mattituck
House No. Street Hamlet
Owner or Owners of Property: George Maul
Suffolk County Tax Map No 1000, Section 121 Block 0 7 Lot 005
Subdivision Filed Map. Lot:
Permit No. �(j Date of Permit. Applicant:
Health Dept. Approval: Underwriters Approval:
Planning Board Approval:
Request for: Temporary Certificate Final Certificate: (check one)
Fee Submitted: $ 6
52
Applicant Signature
i
f
i
Building Department Application
AUTHORIZATION
(Where the Applicant is not the Owner)
f
�L— residingat_ 775 Farmveu Road, Mattituck
(Print property owner's name) (Mailing Address)
do hereby authorize Timothy Ivins
(Agent)
Harvest Power LLC to apply on my behalf to the
Southold Building Department.
4� -
(Owners Signature) ( atc
(Print Owner's Name)
s
I
i
4
CONSENT TO INSPECTION
S
the undersigned,do(es)hereby state:
Owner(s)Name(s)
That the undersigned(is) (are)the owner(s)of the premises in the Town of
Southold,located at 775 Farmveu Rd, Mattituck
which is shown and designated on the Suffolk County Tax Map as District 1000,
¢¢ Section 121 , Block 07 ,Lot 005
That the undersigned has have file or cause to be filed an application in the
g (has) ) d, PP
Southold Town Building Inspector's Office for the following:
That the undersigned do(es)hereby give consent to the Building Inspectors of the
Town of Southold to enter upon the above described property, including any and all
buildings located thereon,to conduct such inspections as they may deem necessary with
respect to the aforesaid application, including inspections to determine that said premises
comply with all of the laws,ordinances,rules and regulations of the Town of Southold.
The undersigned, in consenting to such inspections;do(es)so with the knowledge
and understanding that any information obtained in the conduct of such inspections may
be used in subsequent prosecutions for violations of the laws,ordinances, rules or
regulations of the Town of Southold.
Dated: �� $ � _ _
gnature)
(Print Name)
(Signature)
(Print Name)
OF SOU��®�
Town Hall Annex ® Telephone(631)765-1802
54375 Main Road Fax(631)765-9502
P.O.Box 1179
Southold,NY 11971-0959
�� roger.richertatown.southold.ny.us
,t+
®lyCOU ,�
BUILDING DEPARTMENT
TOWN OF SOUTHOLD
CERTIFICATE OF ELECTRICIAL COMPLIANCE
SITE LOCATION
Issued To George Maul
Address: 775 Farmveu Rd City: Mattituck St: New York Zip: 11952
Building Permit#. 45652 Section 121 Block 7 Lot: 5
WAS EXAMINED AND FOUND TO BE IN COMPLIANCE WITH THE NATIONAL ELECTRIC CODE
Contractor: DBA: Harvest Power License No: 54016
SITE DETAILS
Office Use Only
Residential X Indoor X Basement X Service Only
Commerical Outdoor X 1st Floor Pool
New Renovation 2nd Floor Hot Tub
Addition Survey Attic Garage
INVENTORY
Service 1 ph Heat Duplec Recpt Ceiling Fixtures HID Fixtures
Service 3 ph Hot Water GFCI Recpt Wall Fixtures Smoke Detectors
Main Panel A/C Condenser Single Recpt Recessed Fixtures CO Detectors
Sub Panel A/C Blower Range Recpt Fluorescent Fixture Pumps
Transformer Appliances Dryer Recpt Emergency Fixtures Time Clocks
Disconnect Switches Twist Lock Exit Fixtures TVSS
Other Equipment: 16.56 KWDC roof mounted photovoltaic system to include, 46-360 w modules, wit
Enphase micro inverters, rapid shut down, 100a fused disconnect.
Notes.
Inspector Signature: Date: February 24 2021
81-Cert Electrical Compliance Form.xls
` O�apF SOUTyO!
# TOWN, OF SOUTHOLD BUILDING DEPT. '
765-18027
INSPECT=ION 4 ? ,
[ ] FOUNDATION' 1 ST [ ] ROUGH PLBG.
] FOUNDATION 2ND [ ] INSULATION/CAULKING
[ ] FRAMING /STRAPPING [ ] FINAL
[ ] FIREPLACE"& CHIMNEY [ ] FIRE SAFETY INSPECTION
[ ] FIRE RESISTANT CONSTRUCTION [ ] FIRE RESISTANT PENETRATION
[ ] ELECTRICAL (ROUGH) ELECTRICAL (FINAL)
[ ] CODE VIOLATION [ ] P E C/O
REMARKS:
�17 4��
DATE, 2 _INSPECTOR
`
Graham Associates 1981 Union Blvd. Bay Shore, N.Y. 11706
Building Consultants 0& Expeditors (516) 665-9619 Fax(516) 969-0115
March 9, 3O3l
Town ofSouthold
1 1
�"" . . ��Y '
Building Department �AA --^^
Town Hall Annex
Pl]. Box 1179
Southold,iNY11971
Re: Maul Residence—77SFannveuRd, K8a1tituck, NY119S2
SCTM#1OOO'121-O7-OOS
Permit No.456S3-16.SGkWRooftop Solar Photovoltaic System
ToWhom |tMay Concern,
Please be advised that I have inspected the solar roof array at 775 Farmveu Rd, Mattituck, NY
11952 and have determined that it has been performed in accordance with the manufacturer's
recommendations, and the approved building permit.The installation meets the 2020 NYS Building
Code, 2O1QInternational Code, and ASCE 7'1O.
|fyou have any further questions, donot hesitate tocall.
FIELD INSPEC ION REPOT DANE
FOUNDATION(1ST)•
r
---------------- -------
FOUNDATION
----FOUNDATION(2ND)
ROUGH FRAMING&
PLUMBING
..
i
INS04TION PEA N..Y. � H
STATL ENERGY CODE
FINAL >.
ret-A 1)05
- e r Cir i
m
tz
i
TOWN OF SOUTHOLD BUILDING PERMIT APPLICATION CHECKLIST
BUILDING DEPARTMENT Do you have or need the following,before applying?
TOWN HALL Board of Health
SOUTHOLD,NY 11971 4 sets of Building Plans
TEL: (631)765-1802 Planning Board approval
FAX: (631) 765-9502 �� Survey
Southoldtownny.gov PERMIT NO. Check
Septic Form
N.Y.S.D.E.C.
Trustees
C.O.Application
Flood Permit
Examined '20 Single&Separate
Truss Identification Form
Storm-Water Assessment Form
Contact:
Approved ,20 Mail to:
Disapproved a/c
Phone:
Expiration ,20
for
DEC 2 1 2020 APPLICATION FOR BUILDING PE
Date S , 20
E`,7£,I a7�fr4 INSTRUCTIONS
a. This application MUST be completely filled in by typewriter or in ink and submitted to the Building Inspector with 4
sets of plans, accurate plot plan to scale. Fee according to schedule.
b. Plot plan showing location of lot and of buildings on premises,relationship to adjoining premises or public streets or
areas,and waterways.
c. The work covered by this application may not be commenced before issuance of Building Permit.
d.Upon approval of this application,the Building Inspector will issue a Building Permit to the applicant. Such a permit
shall be kept on the premises available for inspection throughout the work.
e.No building shall be occupied or used in whole or in part for any purpose what so ever until the Building Inspector
issues a Certificate of Occupancy.
f.Every building permit shall expire if the work authorized has not commenced within 12 months after the date of
issuance or has not been completed within 18 months from such date. If no zoning amendments or other regulations affecting the
property have been enacted in the interim,the Building Inspector may authorize, in writing,the extension of the permit for an
addition six months. Thereafter, a new permit shall be required.
APPLICATION IS HEREBY MADE to the Building Department for the issuance of a Building Permit pursuant to the
Building Zone Ordinance of the Town of Southold, Suffolk County,New York,and other applicable Laws,Ordinances or
Regulations,for the construction of buildings, additions, or alterations or for removal or demolition as herein described. The
applicant agrees to comply with all applicable laws, ordinances,building code,housing code,and regulations,and to admit
authorized inspectors on premises and in building for necessary inspections.
Carlo Lanza/Harvest Power LLC
(Signature of applicant or name,if a corporation)
2941 Sunrise Hwy, Islip Terrace 11752
(Mailing address of applicant)
State whether applicant is owner, lessee, agent, architect, engineer, general contractor, electrician, plumber or builder
Agent/Contractor
Name of owner of premises George Maul
(As on the tax roll or latest deed)
If applicant is a corporation, signature of duly authorized officer
(Name and title of corporate officer)
Builders License No. 48165-H
Plumbers License No.
Electricians License No. 54016-ME
Other Trade's License No.
1. Location of land on which proposed work will be done:
775 Farmveu Road Mattituck
House Number Street Hamlet
County Tax Map No. 1000 Section 121 Block 07 Lot 005
Subdivision Filed Map No. Lot
2. State existing use and occupancy of premises and intended use and occupancy of proposed construction:
a. Existing use and occupancy Residence
b. Intended use and occupancy
3. Nature of work(check which applicable):New Building Addition Alteration
Repair Removal Demolition Other Work Solar
(Description)
4. Estimated Cost Fee $200 . 00
(To be paid on filing this application)
5. If dwelling, number of dwelling units Number of dwelling units on each floor
If garage, number of cars
6. If business, commercial or mixed occupancy, specify nature and extent of each type of use.
7. Dimensions of existing structures, if any: Front Rear Depth
Height Number of Stories
Dimensions of same structure with alterations or additions: Front Rear
Depth Height Number of Stories
8. Dimensions of entire new construction: Front Rear Depth
Height Number of Stories
9. Size of lot: Front Rear Depth
10. Date of Purchase Name of Former Owner
11. Zone or use district in which premises are situated
12. Does proposed construction violate any zoning law, ordinance or regulation? YES NO
13. Will lot be re-graded? YES NO Will excess fill be removed from premises?YES NO
775 Farmveu Road
14.Names of Owner of premises George Maul Address Mattituck, NY 11952 phone No. (516) 369-1290
Name of Architect Michael Dunn Address 198, Union Blvd, Bay ShorephoneNo (631,) 665-9619
Name of Contractor Harvest Power Address 2 941 sunrise Hwy Phone No. (6 31) 647-3402
Islip Terrace, NY 11752
15 a. Is this property within 100 feet of a tidal wetland or a freshwater wetland? *YES NO X
* IF YES, SOUTHOLD TOWN TRUSTEES &D.E.C. PERMITS MAY BE REQUIRED.
b. Is this property within 300 feet of a tidal wetland? * YES NO X
* IF YES, D.E.C. PERMITS MAY BE REQUIRED.
16. Provide survey, to scale, with accurate foundation plan and distances to property lines.
17. If elevation at any point on property is at 10 feet or below, must provide topographical data on survey.
18. Are there any covenants and restrictions with respect to this property? * YES NO X
* IF YES, PROVIDE A COPY.
STATE OF NEW YORK)
SS:
COUNTY OF,
tlem being duly sworn,deposes and says that(s)he is the applicant
(Name of individual signing contract)above named,
(S)He is thei
(Contractor,A16t,Corporate Officer,etc.)
of said owner or owners, and is duly authorized to perform or have performed the said work and to make and file this application;
that all statements contained in this application are true to the best of his knowledge and belief,and that the work will be
performed in the manner set forth in the application filed therewith.
Sworn to before me thi - /-
�✓ day of ��iGyW��20
( JULIE OTT
TE OF NEW YORK.
otary ublic No.01 OT6256196 Signature of Applicant
Qualified in Suffolk County
My Commission Expires 02-21-2024
��,11EF01,f`o BUILDING DEPARTMENT- Electrical Inspector
oy� TOWN OF SOUTHOLD
Town Hall Annex - 54375 Main Road - PO Box 1179
• �� Southold, New York 11971-0959
Telephone (631) 765-1802 - FAX(631) 765-9502
roper:richertcWtown.soufhold,ny:'us,
APPLICATION-FOR ELECTRICAL INSPECTION
REQUESTED BY: Julie Ott Date:,,
Company Name: Harvest Power
Name: John D'Aries/Fulton-Electric _Inc.--
License No.: 54016_-ME email: jott@harvestpower.net _
Address: 2941 Sunrise Hwy. , Islip Terrace-,=-MY 11752
Phone No.: (6_31) 647-3402 _!
JOB SITE INFORMATION: (All Information Required)
Name: George Maul
Address: 775 Farmveu Rd, Mattituck, _NY- 11952
Cross Street: Harvest Lane
Phone No.: (516) 369-1290
gPermit#:
Bld _ - _ � - ---- - ----�— --- _--_— - -
_ _ _� �_ �2- -_ email:
T. 7 District: 1000 _ Section: 121 Block__o Lot:_0 0 5 _
BRIEF DESCRIPTION OF WORK(Please Print Clearly)
16 . 56kW Solar Pv System w/_(46)_REC360AA_ Roof-Mounted Panels
Circle All That Apply:
Is job ready for inspection?: YES / NO Rough In Final
Do you need a Temp Certificate?: YES/ NO Issued On
Temp Information: (All information required)
Service-Size 1DPh3 Ph Size: _2 0 0___ _ A #Meters_ - Old Meter#
tNew Service - ire Reconnect- Flood Reconnect-Service Reconnects -Underground - verhead
nderground Laterals 1 2 H Frame Pole Work done on Service?-_ Y N _ -
Additional Infor=mation: _-- -
- - PAYMEN-T_DUE WITH APPLICATION
82-Request for Inspection Form.xls 16)
1 � -zq
l
HARVEST P ® W E R
Harvest Power LLC 2941 Sunrise Hwy , Islip Terrace, NY 11752 Office: 631-647-3402 Fax: 631-647-3404
March 9,2021 T ~_
; s
Town of Southold 4 ;
Building Department MAR 1 1 2021
P.O. Box 1179
Southold,NY 11971 ;
Re: Revised Engineer's Post-Install Letter
Maul Residence—775 Farmveu Rd,Mattituck—BP#45652
Dear Town of Southold Building Department:
Enclosed, please find the revised Engineer's post-install letter including current code
information for the PV solar installation completed at the above referenced residence.
Thank you for your attention to this matter. If you need any further information,please
contact me at(631)647-3402 or via email at joit@harve5Vower.net.
Very truly yours,
6- Q�t_
2_
;xpeditor�
' Ott
Licensed, insured & bonded I License # Nassau County- H0811250000 1 License # Suffolk County 48165-H
r k
APPROVED AS 0 EDS
DATE:
B.P.#
FEE: BY:
NOTIF BUILDING DEPARTMENT AT
765-1802 8 AMSPECTON' FOR, THE
FOLLOWING IN
1. FOUNDATION.= TWO=REQUIRED
FOR POURED-,CONCRETE
2. ROUGH - FRAMING-&,PLUMBING
3. INSULATION-
4. FWAL -, C0 STRUCTION�_MUST
BE COMPLETE FOR"C.O.
ALL CONSTRUCTION -'SHALL,MEET THE
REQUIREMENTS"LOF THE CODES OF NEW
YORK: OR
DESIGN OR CONSTRUCTION Spo�S(BLE ERRORS.
WITH ALL CODES OF
COMPLY STATE &OWN CODES
NEW YORK IONS OF
AS REQUIRED A
SOUTHOLD T N ZBA
SOUTH TOWN PLANNING BOARD
SO OLD TOWN TRUSTEES
N .S.DEC
OCCUPANCY OR
USE IS UNLAWFUL
WITHOUT CERTIFICATE
OF OCCUPANCY
EL.EC'1RICAL INSPECTION REQUIRED
RETA'N STO�t�Ji WATER RUNOFF
PURSUANT TO CHAPTER 236
OF THE TOWN CODE.
Graham Associates 1981 Union Blvd Bay Shore,N.Y. 11706
Building Consultants & Expeditors (631)665-9619 Fax(631)969-0115
December 15, 2020
Town of Southold
Building Department
54375 Rt. 25
Southold, NY 11971
Re: Maul Residence
775 Farmveu Rd.
Mattituck, NY
16.56 kWDC, 13.34 kWAC Rooftop Solar Photovoltaic Systems
To Whom It May Concern,
Please be advised that I have analyzed the existing roof structure at the
above-mentioned premises and have determined that it is adequate to
support the additional load of the solar panels and a 130 mph wind load
without overstress, in accordance with the following:
The 2020 New York State Uniform Fire Prevention and Residential Building
Code; Town of Southold Local Code, Long Island Unified Solar Permit
Initiative, (LIUSPI); and 2020 National Electric Code NFPA 70/2020
National Electric Code including ASCE7-10
If you have any further questions, do not hesitate to call.
sq r
is a
� .FRS
to
. . �
�\
- \ -� � --
. �� �
y�r
f�
All, 2
MJ 1.
� .
` � � - -- - - ---� - ---- - - � - - �
.
. ...
E/PERE\EE
375
RE/
\^ 25 YE�k
� �� P�TUT `
2
&ARR NTY�
POWER ^ �
ELIGIBLE FOR PERFORMANCE
' EC ALPHA : LACK SERIES
PRODUCT OATAS'HE=ET
a 1721±25[6775±01]
281111 802[31 51 455[179] QCERTIFICATIONS
e IEC 61215 2016,IEC 61730 2016,UL 1703,UL 61730
- - -------------------------
❑ j + IEC 62804 PID
\ 1000[39]
IEC 61701 SaltMlst
IEC 62716 Ammonia Resistance
ISO 11925-2 Ignitabdity(Class E)
IEC 62782 Dynamic Mechanlca_I Load
IEC 61215-2 2016 Hailstone(35mm)
m AS4040 2 NCC 2016 Cyclic Wind Load
N ry 150140012004,15090012015,OHSA5180012007,IEC62941
+1 p
11+0+ ! 15take®wa a
O E `R® take rwa WEEE mm Ilan[
[043c us
� �_� I recytlmgs[heme
zo s±o s�f�— I WARRANTY'
[078±008],) ` 1200[47] — { Standard REC ProTrust
InstalledbyanREC Certfied No Yes Yes
y i - -- - 7 Solar Professional
—�-
zz 5[0 9] 621±3[za 5±o l z] System Size All 425 kW 25-SOO kW-�—45[1 51 "q _Product Warranty(yrs) _ 20 ___25 _ _25 _
30[1 181 ty(yrs) 2S 25 25wei Warran rs _
Measurements In mm[in] A Po
Labor Warranty(yrs) 0 25 10
�GENERALDATA Power inYear 1 98% 98% 98%
120 half-cut cells with REC' StaubhMC4PV-KBT4/KST4(4mm2) Annual Degradation 025% 02S% 025%
Celltype heterolunctioncell technology Connectors in accordance with 1EC62852 Power in Year 2S 92% 92% 92%
6 strings of 20 cells in series IP68 onlywhen connected See warranty documents for details Condltionsapply
Glass 32 mm solarglass with Cable 4MM2 solarcablejOm+12m
anti-reflection surface treatment in accordance with EN 50618 MAXIMUM RATINGS
HighlyresistantOperational temperature -40 +85°C
Backsheet Dimensions 1721x1016x30mm(175ml)polymeric construction(black) Maximum system voltage 1000V
Frame Anodized aluminum(black) Weight 19 5 kg Design load(+)snow 4666 Pa(47S kg/m2)'
Maximum test load(+) 7000Pa(713kg/m2)+
Junction box 3-part,3bypass diodes,IP67rated Origin Made inSingapore 2'
in accordance with IEC62790 gDesign load(-)wind 2666 Pa kg/m)
Maximum test load(-) 4000 Pa(407kg/m2)*
ELECTRICAL DATA Product Code*:RECxxxAA Black Max series fuse rating 25A
PowerOutput-PMAx(Wp) 355 360 365 370 37S Max reverse current 25A
-Calculated us Ing a safety factor ofl 5 v
Watt Class Sorting-(W) -0/+5 -0/+5 -0/+S -0/+5 -0/+5 'See installation manua I for mounting instructions
Nom inaIPower Voltage-VmppIV) 364 367 371 374 378
u Nominal Power Current-Impp(A) 977 982 985 99 994 9TEMPERATURERATINGS' UW
1- - Nominal Module Operating Temperature 44°C(±2°C)
in Open Circuit Voltage-V0cIV) 436 439 440 441 442 Temperature coefficient ofPMAx 026%/°C
Short Circuit Current-I (A) 1047 10 49 10 52 1055 1058 ec - - . Temperature coefficient of Voc -0 24%/°C _
Power Density(W/m') 2028S 20S71 20857 21142 21428 Temperature coefficient of Isc 0 04%/°C a
Panel Efficient /0 20 3 20 6 20 9 21 2 21 4
Y(�) The temperature coefficients stated are linearvalues
Power Output-PMAx(Wp) 271 274 278 282 286 LOW LIGHT BEHAVIOUR
a
F NominalPowerVoltage-Vmpp(V) 343 346 350 352 356 Typical low irradiance performance ofmodule at STC o
0
2 Nominal Power Current-IMae(A) 789 7 93 7 96 800 803 0,m --_ ._---.
Z ^�
Open Circuit Voltage-Voc(V) 411 414 415 416 416 N
N
Short Circuit Current-Isc(A) 8 46 8 47 8 50 8 52 8 55 w
I?
Values at standard test conditions(STC air mass AM I S,irradiance 1000 W/m2,tempera Lure 25'C),based on a production spread with ¢
a tolerance ofP_,Va,&Is,±3%within one wait class Nom Ina l mo dule op era ung l empera lure(NMOT air mass AM 15,Irradiance
800 W/m2,tempera ture 20'C,windspeed I m/s)*Where xxx indicates the nominal power class(p,.)atSTC above m Irradiance(W/m2)`°
REC Group is an international pioneering solar energy company dedicated to empowering
` ' ti 11+ consumers with clean,affordable solar power in order to facilitate global energy transitmns
Committed to quality and Innovation,REC offers photovoltaic modules with leading high quality, �'. _
backed by an exceptional low warranty claims rate of less than 10Oppm Founded in Norway in 1996, wwwrecgr0upc0m^
REC employs 2,000 people and has an annual solar panel capacity of 18 GW With over 10 GW-
} b y Installed worldwide,REC=is empowering more than 16 million people with clean solar energy REC Q '❑�
Group is a Bluestar Elkem company with headquarters In Norway,operational headquarters in
Singapore,and regional bases in North America.Eur6pe andAsia-Pacific- } 4 ,
Data Sheet
Enphase Microinverters
Region US
The high-powered smart grid-ready
Enphase Enphase IQ 7 MlcroTM and Enphase IQ 7+ MlcroTM
7 and I + dramatically simplify the Installation process while
achieving the highest system efficiency.
Microinverters Part of the Enphase IQ System,the IQ 7 and
IQ 7+ Mlcroinverters Integrate seamlessly with
the Enphase IQ Envoy'"', Enphase Q Aggregator'M
Enphase IQ BatteryTM, and the Enphase Enlighten TM
monitoring and analysis software.
IQ Series Mlcroinverters extend the reliability
standards set forth by previous generations and
undergo over a million hours of power-on testing,
enabling Enphase to provide an Industry-leading
warranty of up to 25 years
Easy to Install
• Lightweight and simple
Faster installation with improved,lighter two-wire cabling
• Built-in rapid shutdown compliant(NEC 2014&2017)
I ' Productive and Reliable
• Optimized for high powered 60-cell and 72-cell*modules
More than a million hours of testing
• Class II double-insulated enclosure
• UL listed
m
Smart Grid Ready
• Complies with advanced grid support,voltage and
frequency ride-through requirements
w
$ti Remotely updates to respond to changing
grid requirements
Configurable for varying grid profiles
Meets CA Rule 21 (UL 1741-SA)
U� *The IQ 7+Micro is required to support 72-cell modules
To learn more about Enphase offerings,visit enphase.corn �* H S
Enphase IQ 7 and EQ 7+ Microinverters
INPUT DATA(DC) IQ7-60-2-US IQ7PLUS-72-2-US
Commonly used module pairings' 235 W-350 W+ 235W-440W+_
Module compatibility 60-cell PV modules only 60-cell and 72-cell PV modules
Maximum input DC voltage 48V 60V
Peak power tracking voltage 27 V-37 V 27V-45V
Operating range 16 V-48 V 16V-60V
Min/Max start voltage 22 V/48 V 22 V/60 V
Max DC short circuit current(module Isc) 15A 15A
Overvoltage class DC port II II
DC port backfeed current 0 A 0 A
PV array configuration 1 x 1 ungrounded array,No additional DC side protection required,
AC side protection requires max 20A per branch circuit
OUTPUT DATA(AC) IQ 7 Microinverter IQ 7+Microinverter
Peak output power 250 VA 295 VA
Maximum continuous output power 240 VA 290 VA
Nominal(L-L)voltage/range2 240 V/ 208V/ 240 V/ 208V/
211-264 V 183-229 V 211-264 V 183-229 V
Maximum continuous output current 1 0 A 1 15 A 1 21 A 1 39A
-- -- - - -- - - - - - -- - - - - -- --- ---- -- -------- -- -- - - - - -
Nominal frequency 60 Hz 60 Hz
Extended frequency range 47-68 Hz 47-68 Hz
- - - - - - - -- -- -- - -- - - --- - - -- - -- -- - -- -
AC short circuit fault current over 3 cycles 5 8 Arms 5 8 Arms
Maximum units per 20 A(L-L)branch circuit3 16(240 VAC) 13(240 VAC)
13(208 VAC) 11 (208 VAC)
-- - - - - -- - -- -- ---- - --- - - - -- - - - -- - - - - - - -
Overvoltage class AC port III III
AC port backfeed current 0 A 0 A
Power factor setting 10 1.0
Power factor(adjustable) 0.7 leading 0 7 lagging 0 7 leading 0 7 lagging
EFFICIENCY @240 V @208 V @240 V @208 V
Peak CEC efficiency 97.6% 976% 975% 973%
CEC weighted efficiency 970% 970% 970% 970%
MECHANICAL DATA IQ 7 Microinverter
Ambient temperature range -40°C to+65°C
Relative humidity range 4%to 100%(condensing)
Connector type MC4(or Amphenol H4 UTX with additional Q-DCC-5 adapter)
Dimensions(WxHxD) 212 mm x175 mm x 30 2 mm(without bracket)
Weight 1 08 kg(2.38 lbs)
Cooling Natural convection-No fans
Approved for wet locations Yes
Pollution degree PD3
Enclosure Class II double-insulated,corrosion resistant polymeric enclosure
Environmental category/UV exposure rating NEMA Type 6/outdoor
FEATURES
Communication Power Line Communication(PLC)
Monitoring Enlighten Manager and MyEnlighten monitoring options
Both options require installation of an Enphase IQ Envoy
Disconnecting means The AC and DC connectors have been evaluated and approved by UL for use as the load-break
disconnect required by NEC 690.
Compliance CA Rule 21 (UL 1741-SA)
UL 62109-1,UL1741/IEEE1547,FCC Part 15 Class B, ICES-0003 Class B,
CAN/CSA-C222 NO 1071-01
This product is UL Listed as PV Rapid Shut Down Equipment and conforms with NEC-2014 and
NEC-2017 section 69012 and C221-2015 Rule 64-218 Rapid Shutdown of PV Systems,for AC
and DC conductors,when installed according manufacturer's instructions
1 No enforced DC/AC ratio See the compatibility calculator at https//enphase cam/en-us/support/module-compatibility
2 Nominal voltage range can be extended beyond nominal if required by the utility
3 Limits may vary Refer to local requirements to define the number of micro!nverters per branch in your area
To learn more about Enphase offerings,visit enphase.com E N P- /QS E
2018 Enphase Energy All rights reserved All itademarks of brands used ale the propel ty of Enphase Energy,Inc op
2018-02-08
i
t
PHOTOVOLTAIC ROOF MOUNT SYSTEM
46 MODULES-ROOF MOUNTED - 16.56 kWDC, 13.34 kWAC
775 FARMVEU RD,MATTITUCK, NY 11952, USA HARVESTPO ER
HARVEST POWER LLC
SYSTEM SUMMARY: 2sa1 SUNRISE
Y HIGHWAY
GOVERNING CODES: SHEET INDEX TETEL:(801)9893585
(N)46-REC SOLAR REC360AA(360W)MODULES 2017 NATIONAL ELECTRICAL CODE(NEC) PV-0 COVER SHEET websrte:www.harvestpowernet
(N)46-ENPHASE IQ7PLUS-72-2-US MICRO-INVERTERS 2020 NEW YORK STATE UNIFORM CODE PV-1 SITE PLAN WITH ROOF PLAN
(N)JUNCTION BOX 2020 NEW YORK STATE RESIDENTIAL BUILDING CODE PV-2 ATTACHMENT DETAILS
(E)200A MAIN SERVICE PANEL WITH(E) 150A MAIN BREAKER PV-3 SINGLE LINE DIAGRAM
(N) 100A FUSED AC DISCONNECT PV-4 PLACARDS&WARNING LABELS
(N)ENPHASE IQ COMBINER BOX PV-5 ADDITIONAL NOTES
PV-6+ EQUIPMENT SPEC SHEETS
DESIGN CRITERIA:
ROOF TYPE:-ASPHALT SHINGLE VERSION
NUMBER OF LAYERS:-01 DESCRIPTION DATE REV
ROOF FRAME:-2"X8"RAFTERS 16"O.C. BLDG.PERMIT 12/15!2020 0
STORY:-ONE STORY
SNOW LOAD:-25 PSF
WIND SPEED:-130 MPH
WIND EXPOSURE:-B
GENERAL NOTES:
1. INSTALLATION IN ACCORDANCE WITH MANUFACTURER
ARRAY LOCATIONS . '`� -�" � � C)
RECOMMENDATIONS. 9<, �:/ Macanvmeyards� � 1 \ —1
2. ENGINEER TO INSPECT PROJECT AFTER INSTALLATION
__k;_, �\ PROJECT SITE
AND CERTIFY COMPLIANCE.
3. PROJECT TO BE INSTALLED WITH CODE COMPLIANT - �� rvorm rant p
' Church of Christ
RACKING INSTRUCTIONS FOR UNI-RAC SOLAR MOUNT
Juniper-HIIII
SYSTEM. l a I �� J E
4. FOLLOW BALLASTING SCHEDULE ON ROOF PLAN. K pve tit
OENIX `Sound' Cedar House
5. HARVEST POWER, LLC.,THE SOLAR INSTALLATION �" ARLEY��__
:��3 K \ on Sound B&B
CONTRACTOR, COMPLIES WITH ALL LICENSING&ALL . ` ;, >.,�1.ty �'� �EMPIRE STATE JR 1 +i
RELATED REQUIREMENTS OF THE GOVERNING ° :_' y _ Tempoi ily elosnd \` 1` Q O Z Q
MUNICIPALITIES AND THE LOCAL ELECTRIC UTILITY a '°" \ �� C:)
0
AHJ'S. Nr _ =
6. THIS PROJECT WILL COMPLY WITH THE CURRENT NEC J N O X:
REQUIREMENTS INCLUDING ARTICLE 690 SOLAR LO O C7
" s �'
PHOTOVOLTAIC PV SYSTEMS. �' \ Q ti Z 0
7. THE ROOF WILL HAVE NO MORE THAN A SINGLE LAYER 5
OF ROOF COVERING IN ADDITION TO THE SOLAR s;� `> ,� ¢a 7,75Farmveu t > >_ O J
r� 2 Rd,Mattltuck NY_ ;` t LIJ O LL
EQUIPMENT. a t= 9 \�. (D Z 0
8. INSTALLATION WILL BE FLUSH-MOUNTED, PARALLEL Q Y W Z
TO AND NO MORE THAN 6.5"ABOVE ROOF ! �,-. y `� (n
9. MAINTAIN A MINIMUM OF 18"CLEARANCE AT RIDGE ,' \ W C:) a
AND AT ONE GABLE EAVE. LO
I--
10. THIS DESIGN COMPLIES WITH 130 MPH WIND 0 ti
- - �
REQUIREMENTS OF THE RESIDENTIAL CODE OF N.Y.S Z
AND ASCE 7-16. Q J =
11. WHEREVER THE ROOF PLAN DOES NOT COMPLY WITH Q ? Q
ACCESS AND VENTILATION REQUIREMENTS OF THE
UNIFORM CODE, HARVEST POWER PROPOSES THAT
ALTERNATIVE VENTILATION METHODS WILL BE Y
EMPLOYED. REVIEW AND APPROVAL SHALL BE AT THE ,�,: `', SHEET NAME
DISCRETION OF THE MUNICIPALITY IN WHICH THIS r• "3 •
DOCUMENT HAS BEEN FILED. COVER SHEET
12. THE DESIGN PLANS COMPLY WITH THE 2020 NEW
YORK STATE UNIFORM FIRE PREVENTION AND AERIAL PHOTO VICINITY MAP
� SHEET NUMBER
RESIDENTIAL BUILDING CODE. 1 SCALE: NTS 2 SCALE: NTS -o
j Pv
MODULE TYPE, DIMENSIONS & WEIGHT ROOF ACCESS AREA: '
SHALL BE LOCATED IN AREAS THAT DO NOT REQUIRE THE 'C��\�`G -OHO
f,UMBER OF MODULES=46 MODULES PLACEMENT OF GROUND OVER OPENINGS SUCH AS x'
U
MODULE TYPE=REC SOLAR REC360AA(360W)MODULES WINDOWS OR DOORS,AND LOCATED AT STRONG POINTSOQ�G� 'o
MODULE WEIGHT=43 LBS/19.5 KG. In
OF BUILDING CONSTRUCTION IN LOCATIONS WHERE THE Qom/
MODULE DIMENSIONS= 67.8"X 40.0"= 18.83 SF ACCESS POINT DOES NOT CONFLICT WITH OVERHEAD /
UNIT WEIGHT OF ARRAY=2.28 PSF OBSTRUCTIONS SUCH AS TREE LIMBS,WIRES OR SIGNS. I—IAF2VESTPOaR
\� HARVEST POWER LLC
/ 2941 SUNRISE HIGHWAY ISLIP
/ TERRACE,NY 11752
/ TEL (801)989-3585
website.www.harvesfpowernet
/
ROOF#2 p6 �
(18) REC360AA(360W) 5. r/r ;
RAFTERS=2"x8"@16"O.0 / 4 C � \ VERSION
60°AZIMUTH,24°TILT DESCRIPTION DATE REV
ONE-STORY HOUSE / \ BLDG.PERMIT 12/15/2020 a
(E)TREE(TYP.) /4 rr
(E)POOL
(46) ENPHASE IQ7PLUS-72-2-US
MICRO-INVERTERS ,r ((Y
/r /
ev
/ ! J 'p '
ly
Yo
\ �� ,�� •• •• / (N)JUNCTION BOX � Q
4 � •'.•' • ` � �>;' �3�yoy / \ (N)3/4"EMT CONDUIT j 04 0 E—
,� • / RUN 1/2"ABOVE ROOF Q = Lo O Z
• \ 0
ROOF#1 4 ; '� r�, `� W 0 0 fA
J c c� �� / \ Lu > c:) LL
(28) REC360AA(360W) \ �� (� �� ` �> / ,� \ z , 0 0
RAFTERS=2"x8"@16"O.0 �\ �. , ��/ \ (E)200A MAIN SERVICE PANEL Y W Z
240 AZIMUTH,24 TILT cp. EXISTING r QL. U (�
DRIVEWAY (E)STRUCTURE \ WITH (E) 150A MAIN BREAKER 0 L 0 D..
(BASEMENT) W U O
SEE ENLARGE 0 }
VIEW ON PV-1/2 I ¢ a �J--
o
0 ; �s � a0
710 .01
(E) UTILITY METER
(N) 100A FUSED AC DISCONNECT SHEET NAME
Q 6 / SITE PLAN WITH
(N) IQ COMBINER 3S ROOF PLAN
\
SITE PLAN WITH ROOF PLAN ENLARGE VIEW �� // SHEET NUMBER
SCALE:SCALE: 1/32"= 1'-0" SCALE. NTS
a e
ENLARGE VIEW (PV-2/2)
HARVESTEPOWE
HARVEST POWER LLC
2941 SUNRISE HIGHWAY ISLIP
TERRACE,NY 11752
PV MODULES TEL:(801)989-3585
website•www.harvestpowernet
16, O,
(E)ASPHALT SHINGLE VERSION
ROOF(TYP.) DESCRIPTION DATE REV
BLDG PERMIT 12/15/2020 0
GENERAL NOTES:
1. RAILS TO BE INSTALLED TWO PER PANELS AS SHOWN IN DETAIL. E iC S
2. ALL PENETRATIONS TO BE MADE@ 48"O.C. R ;,
3. BOLTS TOBE INSTALLED INTO RAFTERS.
4. MINIMUM 2"PENETRATION INTO WOOD FOR CODE COMPLIAN
ATTAC H M ENT DETAIL 'AOC UAL ROOF CONDITIONS AND RAFTER(OR SEAM)LOCATION &Y '� z
1 VARY. INSTALL PER MANUFACTURER(S)INSTALLATION GUIDELIN-8 ` r
SCALE: NTS AND ENGINEERED SPANS FOR ATTACHMENTS." C)
NAME
PV MODULES
Lo -3 O
J ❑ N O _
UNIRAC SM LIGHT RAIL rn p U
L-FOOT W o O O
FLASH KIT PRO LLI Z C) J LL.
(E) ASPHALT SHINGLE O Of 04 (!)
O
w QY V-- U) z
ROOF (TYP.) ROOF/ DECK MEMBRANE IO LLj Lo o a O
0 F- I-
BUILDING STRUCTURE 5/16" STAINLESS STEEL LAG BOLT Q d- J =
2.5 MIN. OR 2-1/2" MIN. EMBEDMENT AND SS EPDM Q Q
EMBEDMENT WASHER
SHEET NAME
ATTACHMENT
DETAIL
2 ATTACHMENT DETAIL (ENLARGE VIEW) SHEET NUMBER
SCALE: NTS r V-2
+ a
(46) REC SOLAR REC360AA(360W) MODULES BILL OF MATERIALS
'(46) ENPHASE IQ7PLUS-72-2—US MICRO—INVERTERS EQUIPMENT QTY DESCRIPTION {{ -
(03) BRANCHES OF 12 MODULES & SOLAR PV MODULE 46 REC SOLAR REC360AA(360W)MODULES T
(01) BRANCH OF 10 MODULES INVERTER 46 ENPHASE IQ7PLUS-72-2-US MICRO-INVERTERS
COMBINER BOX 1 ENPHASE IQ COMBINER BOX H�D
SYSTEM SIZE:—46 x 360W= 16.56 kWDC JUNCTION BOX 1 600V,55A MAX,4 INPUTS,MOUNTED ON ROOF FOR WIRE&CONDUIT TRANSITION HARVEST O IE
46 x 290W= 13.3 kWAC AC DISCONNECT 1 100A FUSED, 70Al2P FUSE,240V NEMA 3R,UL LISTED HARVEST POWER LLC
2941 SUNRISE HIGHWAY ISLIP
TERRACE,NY 11752
TEL (801)989-3585
12 MICRO—INVERTERS IN BRANCH CIRCUIT#1 website.www harvestpowernet
BI-DIRECTIONAL
UTILITY METER
1-PHASE,3-W,
120V/240V,60Hz
ti ti ti IF
VERSION
DESCRIPTION DATE REV
BLDG PERMIT 12/15/2020 0
12 MICRO—INVERTERS IN BRANCH CIRCUIT#1 I SUPPLY TAP WITH L ?
JUNCTION TAP BOX _
u 1-
• • • 1 3/4"EMT CONDUIT RUN N 12X12X6
1 (8)#10 AWG THWN-2 JUNCTION
e- 1
(1)#8 AWG THWN-2 GND TAP BOX �" �p�;_r f
ti ti 1
- - - - - - - - - - (N)ENPHASEIQ c �
- - �zw�r
COMBINER BOX 150A
12 MICRO—INVERTERS IN BRANCH CIRCUIT#2 0 o ENVOY MD ./ /
(E)200A MAIN
1 (N)JUNCTION (N)AC DISCONNECT: SERVICE PANEL
BOX 10A 100A FUSED,/w W/(E)150A
1 70A/2P FUSES,240V PROJECT NAME
• • • 20A � MAIN BREAKER
NEMA 3R, UL LISTED, (TOP FED)
70A/2P FUSE ^ � p0 Q 0
^, ^, ^, 1 2A U.) -1 0
— — — — - - - - - - G J N O
— — - - �G - - - — - - G - - - - - - - - D � O
10 MICRO—INVERTERS IN BRANCH CIRCUIT#3 Qtr Z0
� - ti
- - W 0 0 U)
J
• 1 � N W
'miff
1 (3)#4 AWG THWN-2 GROISTING 0 < () Cl U)Z
(1)#8 AWG THWN-2 CU GND SYSTEM Ali O a
1 (4)Q-CABLE 1"EMT CONDUIT Lo
1 (1)#6 BARE COPPER GND ~ O O
- - - - - - - - - - - - � < Q ~ Q
(46)ENPHASE IQ7PLUS-72-2-US _
MICRO-INVERTER
SHEET NAME
TERMINATOR CAP ON LAST CABLE
CONNECTOR AC TRUNK CABLE(TYP)
SINGLE LINE
DIAGRAM
1 SINGLE LINE DIAGRAM SHEET NUMBER
SCALE: NTS PV-3
4"
AwARNING _ AWARNING_
ELECTRICAL SHOCK HAZARD PHOTOVOLTAIC SYSTEM SOLAR PV SYSTEM EQUIPPED
COMBINER PANEL c�flp
WITH RAPID-SHUTDOWN TERMINALS ON LINE AND LOAD DO NOT ADD'LOADS HARVESTPOWER
SIDES MAY BE ENERGIZED IN _ _ _ -_ - _ HARVEST POWER LLC
THE OPEN POSITION LABEL LOCATION: 2941 SUNRISE HIGHWAY ISLIP
PHOTOVOLTAIC AC COMBINER(IF TERRACE,NY 11752
LABEL LOCATION: APPLICABLE). 989-3585
website www.harvestpowernet
INVERTER(S),AC DISCONNECT(S),AC TURN RAPID SHUTDOWN
COMBINER PANEL(IF APPLICABLE). SWITCH TO THE"OFF" SOLAR ELECTRIC
PV PANELS
POSITION TO SHUT DOWN
PV SYSTEM AND REDUCE
SHOCK HAZARD IN THE
ARRAY.
VERSION
FOR SOLAR
DESCRIPTION DATE REV
LABEL LOCATION: BLDG.PERMIT 12/15/2020 0
ON OR NO MORE THAT 1 M(3 FT)FROM THE SERVICE
LABEL LOCATION DISCONNECTING MEANS TO WHICH THE PV SYSTEMS
UTILITY SERVICE ENTRANCE/METER,INVERTER/DC ARE CONNECTED.
DISCONNECT IF REQUIRED BY LOCAL AHJ,OR
OTHER LOCATIONS AS REQUIRED BY LOCAL AHJ.
= AWARNING- . N
POWER SOURCE OUTPUT CONNECTION
DO NOT RELOCATE THIS
OVERCURRENT DEVICE
S$'j
LABEL LOCATION'
ADJACENT TO PV BREAKER AND ESS
OCPD(IF APPLICABLE). Q
BUILDING SUPPLIED BY UTILITY co o Q -j-
_ z)
=
Lo _j O
GRID AND PHOTOVOLTAICJ o (.I o U
® ® ® SYSTEM Q ? m o
® ® <2 > ~o O
OJ )
} o
LABEL LOCATION. C� � z O W O
INTERIOR AND EXTERIOR DC CONDUIT EVERY 10 FT, p w N
AT EACH TURN,ABOVE AND BELOW PENETRATIONS, O LL V Z
O
ON EVERY JB/PULL BOX CONTAINING DC CIRCUITS. p �jJ a O
> ti O
< Z
• • • 1 •
Lf) Q F— Q
• •' '• • 1 (E)MAIN SERVICE PANEL
LABEL LOCATION:
(BASEMENT)( SHEET NAME
(E)UTILITY METER
AC DISCONNECT(S),PHOTOVOLTAIC SYSTEM POINT OF (N)AC DISCONNECT PLACARDS &
INTERCONNECTION. (N)COMBINER BOX WARNING LABELS
LABEL LOCATION- SHEET NUMBER
POINT OF INTERCONNECTION
(PER CODE NEC690.56(B),NEC705 10,225.37,230.2(E)) PV-4
i I
1. EACH MODULE TO BE GROUNDED USING THE SUPPLIED CONNECTION POINT PER
MANUFACTURER'S REQUIREMENTS. ALL SOLAR MODULES, EQUIPMENT, AND
METALLIC COMPONENTS ARE TO BE BONDED. IF THE EXISTING GROUNDING HARVESTPOWER
ELECTRODE SYSTEM CAN NOT BE VERIFIED OR IS ONLY METALLIC WATER PIPING, HARVEST POWER LLC
SUNRISEIT IS THE CONTRACTOR'S RESPONSIBILITY TO INSTALL A SUPPLEMENTAL Z941TERRACEHIG,NY;W721SLIP
GROUNDING ELECTRODE. TEL:w(8 an989
23585
website ww.harvesfpowernet
2. ALL PLAQUES AND SIGNAGE REQUIRED BY THE LATEST EDITION OF NATIONAL
ELECTRICAL CODE. LABEL SHALL BE METALLIC OR PLASTIC, ENGRAVED OR
MACHINE PRINTED IN A CONTRASTING COLOR TO THE PLAQUE. PLAQUE SHALL
BE UV RESISTANT IF EXPOSED TO SUNLIGHT.
3. DC CONDUCTORS SHALL BE RUN IN EMT AND SHALL BE LABELED, "CAUTION DC VERSION
CIRCUIT" OR EQUIV. EVERY 5 FT. DESCRIPTION DATE REV
GPERMIT 12/15/2020 0
4. EXPOSED NON-CURRENT CARRYING METAL PARTS OF ELECTRICAL EQUIPMENT
SHALL BE GROUNDED IN ACCORDANCE WITH 250.134 OR 250.136(A).
5. CONFIRM LINE SIDE VOLTAGE AT ELECTRIC UTILITY SERVICE PRIOR TO ,RICH4
CONNECTING INVERTER. VERIFY SERVICE VOLTAGE IS WITHIN INVERTER
VOLTAGE OPERATIONAL RANGE. D , ° m
6. OUTDOOR EQUIPMENT SHALL BE NEMA-3R RATED OR BETTER.
7. ELECTRICAL CONTRACTOR TO PROVIDE CONDUIT EXPANSION JOINTS AND NAME
ANCHOR CONDUIT RUNS AS REQUIRED PER NEC.
8. ALL WIRING MUST BE PROPERLY SUPPORTED BY DEVICES OR MECHANICAL o Q
MEANS DESIGNED AND LISTED FOR SUCH USE, AND FOR ROOF-MOUNTED Z) U.) _j O
SYSTEMS, WIRING MUST BE PERMANENTLY AND COMPLETELY HELP OFF OF THE J 0 c'i o
ROOF SURFACE. NEC 110.2 - 110.4 / 300.4U-) CD
C,
< ? Z
2w — C) Oc)
9. ALL ROOF PENETRATIONS MUST BE FLASHED. SIMPLY CAULKING DOES NOT w > Z N _j LO
SUFFICE. O Q 1 0 co Z
w tiC:)
o a
O � �
~ H Z
< Q1= a
SHEET NAME
ADDITIONAL NOTES
SHEET NUMBER
PV-5
y 5 3L
'!t
I
.9u
ASRM�0 � :•• � AHARVEST HARVEST
�•trn, �, POWER 1",
2941 SUNRISE HIGHWAY ISLIP
WER LLC
294 SUNR SE H
TERRACE,NY 11752
:�
1)989-3585
websitewwwharvestpoweEnet
,1 , � 1' '1 1/ 1 1 I I •I 1' •I 1 •• 1 1 1 �- �` •�?MIT
,,O,PTIm,2t6le OhIIP01dE
1 1 . 11 I 11 1 I 1• I . 1 I • / I 1 '1 1
INTEGRATED BONDING&PRE-ASSEMBLED:PARTS _: #. T r;
1• 1 • •I 1, I 1 • •• • Components are pre-assem letl-and-optrmized`ie retluce irista1latron steps nd save
1 1• I I I .� �,, INTEGRATED BONDING
lao trme 0 newgrouing;&bonding rocess:ehmmates•copperw,r a ntlgroundtng.
•• •• ._k:x -; k = .= lrr : zaMID'CLA'MP _'
1 I 1 I' 1 /• I/ ._ 1 1 I' / '/ 'I '. '1. 1f: ¢is Utrlizethemicromve[termountwdh'rvnte%
1 1 /I I•, strajrs ar�bentlmg`jum era tp reduce cos ;L ,
' I •I •1 1 1 - management clrp"foran easier mstallair n s " � 's � y - ' '
END a VERSATILITY a
CAPS ONE PRODUCT MANY�APPLICATIONS ��
Qurckjy 'e, dduIe flush-to he ronJ or at voosrre tdt angle Change motluleF� � INTEGRATED`B.ONDING'
_ -
101+� �. s ., r SPL CE BAR _
oneritafmnt.porirariandscapewhrtesecunnga.argovartetWof'framedmoduleson` '� - —_—
Y, fla luvrteep pitched roofs ajlibleln mllandl ark anodize8lfinis
- to outperfor r prpjects6nancla and+aesthetc'asplratronsd
r�
.4
10 A1� DkkFF��NN{{yD1 Y
• .. . _ - K� ,r DESIGN PLATFORM AT YOUR SER�YICE ' ' A`"• �= H`• a;=
INTEGRA'TEDBONDING ,,,
z Creating a brtpfanateuafsers fust.a;few chcks�a"wthU Briilder z powrl I online,a L z
sem ..-,Firhirt.;, :rte., , � ,® LFOOTw/T=BOLT r,.
tooltha sr mlinestheprecessof es'gnm acotle,comp(rantsolarmountf1; s stem.
" p d recal pfe erences and'project aufomatrcalty ^y,l
- - aveilmeb. yea in,a ser ro le an ,•� nor ' ,».� f•"
• r. hen,,you�ag n.You vrll enjoy the abili �har�e r,�ectswrth.cus ome s',there's no � j } � '�"� w:
Yl
ee&to'p•nf e5dlls:a d=se'd°to atlistribo`for�just�I`ck and share •�::«, = ,� � ,�_
1 I FRONT ' : : :r x« INTEGRATED_ BDNDING* r °� z � �:. -•
•
f� �I,�I 9F f j��. ��i 1F I;•� Ip1,1 I., � !� I�' I;' TRIM -' ��.." • � ��' �' MICROINV'ERTER MOUNT'iN/ •, ..; � ���. .�
1• 1 � ■ •k � W,IRE M�A MEN'T � '�`
-_ a k
-
�'~_^ MECHA ICA 0 II G �; -
k •
.� STfMtFIREC�SIFlC TIO I 'L' � � -
1`="-�__ • ;s,,rr, SY... 5-.:u-y, 1 r,K4f, ,.ter- `ti::,_ - ,.?/ #�'i 1 �" a • CNT -
--
�. 3' Y Lo
-
,v
�, N1{R� C' ' . 'EyR4 ` VICE MEANS �HE GHEST E�IEL 0 RODU' T ful8211
RT - . co
-
"�;`;f-�,r.-^'dk' :,�
RIO' UJ
R
L : :. .. ; r : ., .-,a -`"'- .�s:�il'..,, __ -,a-`,. - .:.Z:.c_. _ x`L,�-::,,- t -n a.::,y a z
,1. , ,r : r, r r :. ems. ,'., w CD
1 I s 1 1 1. ,OMATCREO„- ?a G RTIF1EUl” r4i kENGINEERiNG . . y�BANIiABLE -
`s'y�k� PE JENEE' =�f�QilALi'TY ?"a E CELEENCE• -t. ' s `��OS "' DOOOh1EN ATION -
w y 3f i YIARTJ�ANTi f #T
1 1 1 1 •1 I 1. 1 I I I I I• .1 .1 1 1 .'t'rri 1�>'">�'�K5 � � � r� •F y ��•:i _q�^sem� +tiT��' � ^� i
•',C ._., ... 9T✓.__;. i., �t -�.a.:+r�',� v r`:. r-....}_....t K» f^ K.•.�s�s. - a
TEBHNIC.AL SUPPORT CERTIFIED QUALITY PROVIDER BAN ABLE WARRANTY,
U rrac' technical su�po team Is dedicated do answecfng ;rq
c is onlylPY mounhrig-vendor th ISO ce `fie%ns, Dont cave you project o cimnce, r irac has tfie,=`firoahe�l
�'r
i3. ues ibn�aUdmssrc rsspes n'eal�time. An,:online 15:lal0OL2O15'-and OHSA 18001:2007 _ )ren 'ib,6aek our products and ieduoe'you r :°Flave•peace-.
means'we deliver the to hest standards for Cd` a mmtl'.°I�ewi ou are'recelvin`prntluds:of exceptanal
.+E =
' r
.e.
NUN
, .,. �. � s m ed letters and technrpl data sheets, great) y orm and fuic'on. ese serfifications demoostraie out, quabty:,SOI/tRMOUtJTt is cpucred by z n ,,Jwe - year
F
NSTALLATLON. SUPERIORAE �HEL a
r ST .. TCS: : . . a. . r � .
_� :.-,. �:.. � m rfies.yo�ermdbn .. od. ro ect ,)aorto roces: .. e><celien e d com d en-to• t class business,racbces.a.. limned mductvraman a-
...............................................
ntlafivc;(5.year rm� a ran . `.: ,
..., .,1. ,.:,, ,.,, ....:. .. ..,_,� .. ,. ,,.-, ,._ •, �.. {,,: � ,.•.. �,_:,: ;�-- .•. .� s!:p-._.- . -. g ._. ,p 1 P�: , g p-_. :...,. .. c,n rpm t ,P 5,�-., p., tY.
�......
'moi• ..�F� c.. ".,.- ,� •, -..�- .:,'.�,. ..,. ":_. "
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 111111 111
i II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII1711111:� _ - -` -r- -•'-
• WON
...�,r•,.+.,w`..s`,1t..�., - :='...)f-Y'?'•�s?`pi.�"'' L.... _.
r:
OPTI, � , , �,� t ..
MIZED C0 _PONENTS . VERSATILITSY �:.�- :,DESIGN �T,OQL`'S • :, UkL�ITY'L�P.ROVI:DER :_� ROTECT ,DURf:R•POTATION TN QUAL+' RAC LING OLDTaONS BAC 'EDB ENGI EE (N •GEL NCE AND A&, IiPE OR;SUP @X GHQ N -,
3
.x•^ip"'" s`..�1-�y �S •-• ::. ,y, :�?•� ..>..;_.�;'-t.. f ;C�a-!.>z '��# a -��''`ti'.Y '.�'�'i r S,°: e _ fig.. - -
, .. .-. ... ........ ... .. . ,. -..-_:._ -. .,, '--fit � ..-;,._ '. -< .i• - 3•_t" :!... .i', -
:
� a
i
A.Hp
HAAVEJTP WIan
Pz/ H HARVEST POWER LLC
2941 SUNRISE HIGHWAY
ISLIP
stru ural structural TERRACE,NY 11752
ENGI�EERS
ENGINEERS TEL (801)989-3585
June 6,2020website www.harvestpowernet
Installation Orientation: See SOLARMOUNT Rail Flush Installation Guide.
Landscape-PV Panel long dimension is parallel to ridge/eave line of roof and the PV
Unirac panel is mounted on the long side.
1411 Broadway Blvd.NE,
Albuquerque,NM 87102 Portrait-PV Panel short dimension is parallel to ridge/eave line of roof and the PV panel
is mounted on the short side.
Attn.:Unirac-Engineering Department Components and Cladding Roof Zones:
Re:Engineering Certification for the Unirac U-Builder 2.0 SOLARMOUNT Flush Rail The Components and Cladding Roof Zones shall be determined based on ASCE 7-05,ASCE 7-10&7-16 Component and VERSION
Cladding design. DESCRIPTION DATE REV
PZSE,Inc.-Structural Engineers has reviewed the Unirac SOLARMOUNT rails,proprietary mounting system constructed BLDG.PERMIT 12/15/2020 0
Notes: 1)U-builder Online tool analysis is only for Unirac SM SOLARMOUNT Rail Flush systems only and do not
from modular parts which is intended for rooftop installation of solar photovoltaic(PV)panels;and has reviewed the U- include roof capacity check.
builder Online tool.This U-Builder software includes analysis for the SOLARMOUNT LIGHT rail,SOLARMOUNT 2)Risk Category II per ASCE 7-16.
STANDARD rail,and SOLARMOUNT HEAVY DUTY rail with Standard and Pro Series hardware. All information,data and 3)Topographic factor,kzt is 1.0.
analysis contained within are based on,and comply with the following codes and typical specifications: 4)Array Edge Factor YE=1.5
1. Minimum Design Loads for Buildings and other Structures,ASCE/SEI 7-05,ASCE/SEI 7-10,ASCE/SEI 7-16 5)Average parapet height is 0.0 ft.
2. 2006-2020 New York State Building Code,by International Code Council,Inc and New York State Department of 6)Wind speeds are LRFD values.
State. 7)Attachment spacing(s)apply to a seismic design category E or less. twd � r
3. 2006-2020 New York State Residential,Code,by International Code Council,Inc and New York State Department
of State. Design Responsibility:
� t
4. 2006-2018 International Building Code,by International Code Council,Inc.w/Provisions from SEAOC PV-2 2017. The U-Builder design software is intended to be used under the responsible charge of a registered design professional Co I ,��'o-�;
5. 2006-2018 International Residential Code,by International Code Council,Inc.w/Provisions from SEAOC PV-2 where required by the authority having jurisdiction.In all cases,this U-builder software should be used under the
2017.
direction of a design professional with sufficient structural engineering knowledge and experience to be able to: o
6. AC428,Acceptance Criteria for Modular Framing Systems Used to Support Photovoltaic(PV)Panels,Novembero �s C ME
1,2012 by ICC-ES. Evaluate whether the U-Builder Software is applicable to the project,and �.� 7 Ro
7. 2015 Aluminum Design Manual,by The Aluminum Association,2015 Understand and determine the appropriate values for all input parameters of the U-Builder software. y0
Q o
Z ❑
Following are typical specifications to meet the above code requirements: This letter certifies that the Unirac SM SOLARMOUNT Rails Flush,when installed according to the U-Builder engineering ? C) O
report and the manufacture specifications,is in compliance with the above codes and'loading criteria.
Design Criteria: Ground Snow Load=0-100(psf) ❑ (V O
Basic Wind'Speed=85-190(mph) This certification excludes evaluation of the following components: ❑ Ln O Q ❑
Height=0-60 ft C:)Roof Mean Hei
g ( ) 1) The structure to support the loads imposed on the building by the array;including,but not limited to:strength Q ❑ � ti Z Q
Roof Pitch=0-45(degrees) and deflection of structural framing members,fastening and/or strength of roofing materials,and/or the effects > �p Q
Exposure Category=B,C&D of snow accumulation on the structure. LLI Z C) (1) ILL
Q
Attachment Spacing: Per U-builder Engineering report. 2) The attachment of the SM SOLARIVIOUNT Rails to the existing structure. W CN LV -
3) The capacity of the solar module frame to resist the loads. olf Q < U V-- (n Z
Cantilever: Maximum cantilever length is L/3,where"L"is the span noted in the U-Builder online d
w C:) Q
tool. This requires additional knowledge of the building and is outside the scope of the certification of this racking system. C7
Clearance: 2"to 10"clear from top of roof to top of PV panel. OF NSW
If you have any questions on the above,do not hesitate to call. �G ,K Zq yo F- Z J =
Tolerance(s): 1.0"tolerance for any specified dimension in this report is allowed for installation. ,t ey �� Q Q
Prepared by: CO a �� * D
PZSE,Inc.—Structural Engineers `_ I
Roseville,CA I, -
Pp$i36�?Q2 SHEET NAME
1478 Stone Point Drive,Suite 190, Roseville,CA 95661 1478 Stone Point Drive,Suite 190, Roseville,CA 95661 AROFESSIONP�
T 916.961.3960 F 916.961.3965 W www.pzse.com T 916.961.3960 F 916.961.3965 W www.pzse.com SPEC SHEETS
Experience I Integrity I Empowerment Experience I Integrity I Empowerment
SHEET NUMBER
PV-7